高铁酸钾对水中藻类及其次生嗅味污染物二甲基三硫醚同步去除研究

模拟高藻期碱性水源水,采用高铁酸钾对水中以颤藻和二甲基三硫醚为代表的藻类及微量嗅味污染物进行同步控制研究.在高铁酸钾与聚合氯化铁(PFC)单独混凝对藻类的控制效果对比的基础上,展开了高铁酸钾与高锰酸钾预氧化-PFC联用方法对藻类及嗅味污染物的控制效果对比,探讨了pH、预氧化时间和浊度等条件对控制效果的影响.结果表明,PFC单独混凝除藻率最高为90.6%,以Fe计的等量投加条件下,高铁酸钾控藻效果较PFC混凝好,除藻率可达92.4%.高锰酸钾对PFC具有强化混凝效果,可明显提高除藻率(94.5%).高铁酸钾较高锰酸钾预氧化对二甲基三硫醚的去除效果理想,且氧化时间大大缩短,高铁酸钾氧化时间1 min可去除92.5%二甲基三硫醚,高于高锰酸钾预氧化10 min后达到的去除率(74.6%).     

常规施肥条件下农田不同途径氮素损失的原位研究:以长江中下游地区夏玉米季为例

为了解农田常规施肥条件下的不同途径氮素损失特征,本文通过田间原位试验同步研究了长江中下游地区夏玉米生长季氮肥施用后的农田N2O排放、NH3挥发、氮渗漏和地表径流的变化.结果表明,在复合肥为基肥,尿素为追肥,基追肥氮素水平均为150 kg·hm-2的条件下,整个玉米生长季N2O排放系数为3.3%,NH3挥发损失率为10.2%,氮渗漏和地表径流损失率分别为11.2%和5.1%.此外,基肥施用以氮素渗漏损失为主,而追肥氮素损失以氨挥发和渗漏为主,表明不同途径化肥氮素损失主要受氮肥品种影响,玉米季追肥可改用低氨挥发氮肥品种以减少氮素损失.     

β-In2S3的制备及其太阳光下降解土霉素

利用水热反应法制备β-In2S3纳米颗粒光催化剂,并利用SEM、TEM和XRD等对其进行分析表征;采用土霉素溶液模拟四环素类抗生素废水,探讨In2S3对土霉素的降解效果.结果表明,β-In2S3为立方相纳米颗粒结构,该纳米颗粒由纳米片组成,直径约15~30 nm.以太阳光为辐射光源,In2S3对土霉素具有良好的光催化降解效果,在4 h内对初始浓度为30 mg·L-1的土霉素降解率可达98%以上.降解土霉素后的催化剂在无水乙醇中清洗并烘干,经4次循环利用后,β-In2S3的降解能力仍能达到85%以上,表明β-In2S3光催化剂具有良好的稳定性以及光催化活性.     

微生物燃料电池改性阳极处理PTA废水

探讨了不同改性阳极对微生物燃料电池(microbial fuel cell,MFC)产电性能及其对MFC处理难降解废水能力的影响.以单室空气阴极为基础,利用0.1 g电气石、质量分数75%二氧化锰/埃洛石纳米管(manganese bioxide/halloysite nanotube,MnO_2/HNT)和多壁碳纳米管-羧基(multi-walled carbon nanotube-carboxyl,MWCNT-COOH)对MFC阳极进行修饰.结果表明,不同改性阳极的MFC对含精对苯二甲酸(purified terephthalic acid,PTA)废水的去除率均高于70%,且化学需氧量(chemical oxygen demand,COD)去除率在79%以上.相较于其他几种改性阳极,以MWCNT-COOH改性材料作阳极的MFC产生的最大输出电压最高,获得的最大功率密度最高,分别为529 mV和252.73 mW·m~(-2).     

Ti/SnO_2-Sb阳极-空气阴极电催化降解染料废水

为解决电化学法处理高盐染料废水存在的能耗大、成本高等问题,分别采用溶胶-凝胶法和辊压法制备Ti/SnO_2-Sb阳极和空气阴极,构建了Ti/SnO_2-Sb阳极-空气阴极双极体系(TSSA-ADC)。甲基橙(MO)作为高盐染料废水的典型污染物,考察了电流强度、MO浓度、电解液浓度和初始p H对TSSA-ADC体系和TSSA单阳极体系降解MO的影响。结果表明:与TSSA单阳极体系相比,TSSA-ADC体系具有更好的抗有机负荷冲击、抗盐分冲击、抗酸碱波动能力,能够维护酸碱平衡防止硬度离子结垢。最佳反应条件为电流强度为0.030 A,电解液浓度为3%,MO浓度为100 mg/L,初始pH=6。以MO去除率达到98%为基准,TSSA-ADC体系比TSSA体系可节能74.26%。     

不同污水处理工艺N_2O减排方法研究进展

污水处理过程中产生强温室气体N_2O的问题已经受到广泛关注,如何在保证处理效率的同时实现N_2O有效减排成为水处理领域面临的重要问题。综述了传统生物脱氮除磷工艺和同步硝化反硝化、反硝化除磷、厌氧氨氧化等新型污水处理工艺运行过程中N_2O的产生机理、减排方法和减排量,为相关领域的研究人员提供参考。     

焙烧温度对CeO_2(ZrO_2)/TiO_2选择性催化脱硝性能的影响

采用溶胶-凝胶法并以不同温度焙烧制备一系列CeO_2(ZrO_2)/TiO_2(CZT)催化剂,考察了CZT催化剂固相结构、酸量、比表面积等性能与催化活性的关系。采用XRD、BET、NH3-TPD、H2-TPR以及XPS等表征技术对催化剂进行表征。结果表明:焙烧温度为450℃时CZT催化剂具有最高的催化活性,其在240~400℃的温度窗口内活性均高于90%,且具有较好的抗水和抗硫中毒能力。随着焙烧温度的提高,催化剂表面的Ce和Zr原子进入体相晶格且Ce0.5Zr0.5O2向Ce0.75Zr0.25O2转变,导致催化剂的储释氧能力和氧化还原性能降低。另外,锐钛矿和金红石型TiO_2晶粒尺寸的增加,催化剂的有效比表面积和总酸量降低,因此CZT催化活性随着焙烧温度的提高而有所降低。换言之,大的比表面积、良好的氧化还原性能、表面Ce4+的富集以及酸性位的增多均有利于NH3-SCR活性的提高。     

UV/H_2O_2对氯消毒副产物TCM、DCBM的去除影响因素研究

针对UV/H_2O_2对氯化消毒副产物三氯甲烷(TCM)和一溴二氯甲烷(DCBM)的去除效果及影响因素进行研究,结果表明UV/H_2O_2方法对TCM和DCBM去除效果的影响因素有过氧化氢(H_2O_2)投加量、紫外光照强度、反应p H值和反应物初始浓度。通过不同的反应条件得出:H_2O_2在一定投加量变化范围(10~35 mmol/L)内,随投加量的增加,TCM和DCBM的去除率均呈先上升后下降趋势,H_2O_2最佳投加量分别为25,20 mmol/L;增大紫外光照(UV)强度,TCM和DCBM的去除率均显著提高;随初始p H值的增大,去除率均呈先上升后下降趋势,p H值为7.0时,去除率达到最佳;TCM和DCBM反应初始浓度分别为150,160μg/L时,其去除率最高,在有效时间内去除率分别为95.88%、92.56%。     

Effect of MoO3 on vanadium based catalysts for the selective catalytic reduction of NOx with NH3 at low temperature

The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.     

In-situ synthesis of TiO2 rutile/anatase heterostructure by DC magnetron sputtering at room temperature and thickness effect of outermost rutile layer on photocatalysis

TiO_2 rutile/anatase heterostructure thin films with varying rutile thickness have been in-situ synthesized via DC magnetron sputtering with Ar gas at room temperature. The crystal texture, surface morphology, energy gap and optical properties of the films have been investigated by X-ray diffraction meter, grazing incidence X-ray diffraction meter, Raman spectroscopy, scanning electron microscopy, and UV–visible spectrophotometer, which indicates that the rutile/anatase heterostructure films are successfully fabricated. The further degradation experiments display that the photocatalytic activity can be dramatically affected by the thickness of the outmost rutile layer and the 100 nm thickness exhibits the best performance in all of the TiO_2 thin films. With the increase of the outmost rutile layer, the optical band gap of TiO_2 film displays a systematic decrease slightly. However,the change in photocatalytic activity does not coincide with that in the band gap. The photoresponse and electrochemical properties of the thin films have been characterized to understand the mechanism of the varied photocatalytic activity.