Spatial & temporal variations of PM10 and particle number concentrations in urban air

The size of particles in urban air varies over four orders of magnitude (from 0.001 μm to 10 μm in diameter). In many cities only particle mass concentrations (PM10, i.e. particles <10 μm diameter) is measured. In this paper we analyze how differences in emissions, background concentrations and meteorology affect the temporal and spatial distribution of PM10 and total particle number concentrations (PNC) based on measurements and dispersion modeling in Stockholm, Sweden. PNC at densely trafficked kerbside locations are dominated by ultrafine particles (<0.1 μm diameter) due to vehicle exhaust emissions as verified by high correlation with NOx. But PNC contribute only marginally to PM10, due to the small size of exhaust particles. Instead wear of the road surface is an important factor for the highest PM10 concentrations observed. In Stockholm, road wear increases drastically due to the use of studded tires and traction sand on streets during winter; up to 90% of the locally emitted PM10 may be due to road abrasion. PM10 emissions and concentrations, but not PNC, at kerbside are controlled by road moisture. Annual mean urban background PM10 levels are relatively uniformly distributed over the city, due to the importance of long range transport. For PNC local sources often dominate the concentrations resulting in large temporal and spatial gradients in the concentrations. Despite these differences in the origin of PM10 and PNC, the spatial gradients of annual mean concentrations due to local sources are of equal magnitude due to the common source, namely traffic. Thus, people in different areas experiencing a factor of 2 different annual PM10 exposure due to local sources will also experience a factor of 2 different exposure in terms of PNC. This implies that health impact studies based solely on spatial differences in annual exposure to PM10 may not separate differences in health effects due to ultrafine and coarse particles. On the other hand, health effect assessments based on time series exposure analysis of PM10 and PNC, should be able to observe differences in health effects of ultrafine particles versus coarse particles.     

氨气敏电极法和纳氏试剂分光光度法对地表水中氨氮的比对测试

采用不同质量浓度的氨氮标准样品和实际样品,用氨气敏电极法和纳氏试剂分光光度法进行同步测试。结果表明,2种分析方法在水样氨氮质量浓度在0. 159～2. 81 mg/L范围内具有良好的可比性、精密性和准确性。氨气敏电极法的检出限为0. 03 mg/L,平行6次测定样品的相对标准偏差为0. 4%～4. 2%,加标回收率为85. 0%～110%;纳氏试剂分光光度法的检出限为0. 025 mg/L,平行6次测定样品的相对标准偏差为0. 5%～6. 4%,加标回收率为93. 0%～99. 8%。同时氨气敏电极法在样品预处理、试剂配制和分析时间上要优于纳氏试剂分光光度法。氨气敏电极法能够满足地表水自动监测在线比对实际工作的需求,该方法具有良好的适用性。     

A study on the factor market distortion and the carbon emission scale effect of two-way FDI

Based on the data of 30 Chinese provinces for the period from 2004 to 2015, this paper expounds the carbon emissions effect of two-way foreign direct investment (FDI) from the perspective of scale effect and factor market distortions. This study uses Kaya identity to decompose carbon emission and construct simultaneous equations model to empirically examine the factor market distortion and the carbon emission scale effect of two-way FDI. The results show that the inward foreign direct investment (IFDI) increase regional carbon emission through scale effect and also exacerbates factor market distortion in China, whereas the outward FDI trends reduce carbon emission and reduces factor market distortions in China. The study also shows that human capital, research and development (R&D), trade openness, and capital accumulation are important determinants of two-way FDI. Therefore, the study proposes that IFDI policies should focus on acquiring green technologies. In addition, the domestic enterprises should be encouraged to participate in global business.     

Influencing climate change regulations: examining responses from large-scale firms

Recent climate change projections and a push towards a universal agreement on carbon emission reductions suggest that firms will need to respond to future regulatory changes. This paper employs an influencing strategies lens to examine how large-scale firms might respond to future climate change regulations. The study uses a structured qualitative methodology to explore and explicate the strategic responses from 21 international firms to the proposed emissions trading scheme outlined in Australia's Garnaut Climate Change Review. The results of the analysis show that firms can use pre-emptive influencing strategies in attempts to shape and mould regulatory design parameters, secure high levels of transitional economic support, and shift the balance of public policies and expenditure. Complementary defensive strategies may also target policy makers and regulators with some of the potential negative consequences of the new regulations.     

Comparative study on effect of blending,thermal barrier coating (LHR) and injector nozzle geometry on biodiesel-fuelled engines

Increased petroleum prices, increased threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for internal combustion engines. Evolving suitable technology for addressing energy crisis creates a continued investigation into the search for sustainable and clean-burning renewable fuels. This work investigates suitability of different non-edible-derived biodiesels such as cotton seed oil methyl ester (COME), Honne oil methyl ester (HnOME) and Rubber seed oil methyl ester (RuOME) to four stroke, single cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel blending, thermal barrier coating (TBC) or Low Heat Rejection (LHR) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and RuOME in the modified CI engine. Blends of biodiesels with diesel were varied from 20 to 80% in steps of 20%. Two thermal barrier coatings of partially stabilized zirconium (PSZ) and aluminium oxide (Al₂O₃) were provided on the engine to make it fully adiabatic. Nozzle injectors of 3, 4 and 5 holes, with size of orifice varied from 0.2 to 0.3 mm size were selected for the study. It was concluded that B20 biodiesel blend, PSZ-coated engine and four hole nozzle injector of 0.2 mm size resulted in overall better engine performance with increased brake thermal efficiency (BTE) and reduced HC, CO, smoke emissions for the fuel combinations tested. Combustion analysis to study the effect of biodiesel blends, LHR coatings, injector nozzle geometry on the performance of the biodiesel-fuelled engine has been presented to give more insight into the behaviour of operation.     

An experimental apparatus for testing biodiesels based on a CFR engine—setup and validation with different methyl ester blends

A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NO_X emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.     

A numerical study on the effects of EGR and spark timing to combustion characteristics and NOx emission of a GDI engine

EGR is one of the most significant strategies for reducing especially nitrogen oxides (NO_x) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NO_x emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NO_x emissions.     

家庭部门生活能源消费碳排放:测度与驱动因素研究

本文运用IPCC的二氧化碳排放量测算方法,在省际层面测度了我国家庭部门直接能源消费碳排放,并基于扩展的STIRPAT和Kaya模型,构建家庭部门直接能源消费碳排放影响因子动态面板数据模型,对我国2003-2012年分省面板数据样本及城乡子样本进行系统GMM估计。本文研究表明,第一,我国城乡家庭部门碳排放总量和人均碳排放在近十年都呈快速上升趋势,家庭部门碳排放的空间分布具有明显的地域差异特征,高碳排放地区主要集中在东、中部地区,西部地区的碳排放水平较低;第二,城乡家庭部门生活能源消费的上期碳排放量对本期碳排放产生重要的正向影响,这反映出我国家庭部门碳排放具有显著的惯性特征和路径依赖性,是一种动态自适应机制;人口规模、居民消费水平、能源消费结构、碳排放强度、能源消费强度和城镇化因素,都对我国居民能源消费碳排放总量及人均碳排放具有显著的影响,城乡之间的家庭能源消费碳排放驱动因素存在差异。本文研究得到如下启示及政策含义:家庭部门碳减排将是一个有步骤、分区域的渐进过程,我国碳减排政策应当兼顾消费升级和碳排放的双重目标,努力构建分层次碳减排的适应性预期机制。具体而言,一方面应着眼于引导和激励居民低碳消费,缓解人口规模增加、消费水平提升和城镇化对家庭部门碳减排的压力;另一方面要通过能源价格改革、财政政策和环境规制政策等优化我国能源消费结构,不断降低煤炭消费比重,提高清洁能源的消费。同时,通过技术创新、设备改造等科技手段提高煤炭利用效率,降低碳排放强度,这些政策将更有利于城镇家庭部门碳减排。     

燃煤电厂烟尘超低排放技术措施研究

针对越来越严格的环保要求,介绍了原有的除尘技术,并对除尘器新技术改造方案进行了说明,其中重点对电袋复合代替静电除尘技术、在静电除尘器中增置旋转电极、更改工频电源为高频电源、在电除尘器前加装低温换热器、脱硫后增加湿式电除尘器技术等方案进行比较分析。为了达到超低排放要求,对不同的烟尘超低排放实践工艺进行了说明,并结合东部沿海地区可再生能源发展空间有限的实际情况,提出加快推广超低排放技术在现有燃煤电厂的应用,实现传统煤电产业和环保产业的转型升级。     

沸石用于去除废水中的氨氮

天然沸石及改性沸石对氨氮有很强的选择性吸附能力。介绍了沸石去除废水中氨氮的应用研究,包括在O/A生物处理系统、二级氧化塘处理系统、土地处理系统、湿地系统和堆肥系统等中的应用。分析了氨氮在沸石上发生吸附和离子交换的主要影响因素和规律。为开拓沸石在废水处理中的应用提供科学与技术基础。