微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

IC反应器处理MTO废水的中试研究

中试研究了内循环(IC)反应器处理甲醇制烯烃(MTO)废水的启动和运行过程,同时考察了颗粒污泥的性状及沼气产量的变化情况。试验过程运行稳定,系统抗冲击性强。以絮状污泥为接种污泥,经过131 d的启动和运行,IC反应器的COD去除负荷可达10 kg/(m~3·d)以上,COD去除率可达90%以上。IC反应器中的成熟颗粒污泥形状规则、密实、粒径大、沉降速率快。IC反应器的沼气产量符合理论预期。     

四氨基酞菁钯/γ-Al_2O_3可见光催化降解罗丹明B

采用浸渍法制备了四氨基酞菁钯(PdTAPc)/γ-Al_2O_3负载型光催化剂,采用UV-Vis,FTIR,XRD,SEM技术对其进行了表征,并将其用于罗丹明B的可见光催化降解,考察了光催化剂加入量、溶液pH、H_2O_2加入量、反应温度对罗丹明B降解效果的影响,并对光催化剂的稳定性进行了测试。表征结果显示,PdTAPc以圆片状负载于γ-Al_2O_3上,二者的结构均未发生明显变化。实验结果表明:在光催化剂加入量1.6 g/L、溶液pH 7.0、H_2O_2加入量12 mmol/L、反应温度20℃的优化条件下反应120 min,罗丹明B(质量浓度0.05 g/L)的降解率高达95%;光催化剂具有较高的稳定性,使用4次后罗丹明B的降解率仍高于85%。     

生物滴滤塔处理模拟甲硫醚废气

在常温条件下,采用生物滴滤塔处理模拟甲硫醚废气,考察了气体空床停留时间(EBRT)、容积负荷、喷淋密度及营养液pH对生物滴滤塔性能的影响。实验结果表明:当EBRT为90 s、进气甲硫醚质量浓度为150 mg/m~3、喷淋密度为0.65 m~3/(m~2·h),营养液pH为6.8时,甲硫醚去除率为90%;容积负荷高于15 g/(m~3·h)时,对生物滴滤塔的性能产生抑制作用;EBRT为90 s及60 s时,最佳喷淋密度分别为0.56~0.65 m~3/(m~2·h)及0.65~0.75 m~3/(m~2·h);降解甲硫醚的微生物对pH的变化较敏感,最适营养液pH为6~7。     

采用支持向量机算法优化电化学处理油田污水的工艺参数

采用支持向量机(SVM)算法,将Box-Behnken设计法与支持向量回归算法(SVR)实验参数优化软件相结合,优化电化学去除油田污水COD的工艺参数。通过量子粒子群算法对SVM算法参数进行优化,从建立的回归模型中找到工艺参数的全局最佳点:电解时间60 min,电解电流3 A,三维电极填充料中石英砂质量695 g。模型得到的COD理论最优去除率为92.48%,验证实验得到的COD去除率为91.43%。     

羟基乙叉二膦酸镀铜废液的处理及Cu~(2+)的高附加值资源化回收

采用Na BH4还原法将羟基乙叉二膦酸(HEDP)镀铜废液中的Cu~(2+)制备成纳米铜粉,并采用聚丙烯酰胺(PAM)对还原反应后的废液进行絮凝处理。研究了n(Cu~(2+))∶n(Na BH4)、还原反应温度、还原反应时间及PAM添加量对废液中剩余Cu~(2+)质量浓度的影响,并对回收的纳米铜粉进行了XRD和TEM表征。实验结果表明:当n(Cu~(2+))∶n(Na BH4)=4∶6、还原反应温度为50℃、还原反应时间为2 h时,废液中剩余Cu~(2+)质量浓度降低至1.1 mg/L,Cu~(2+)还原率达99.99%;可获得粒径为20~45 nm的近球型、高纯度、由多晶组成的纳米铜粉;当PAM添加量为10 mg/L时,废液中剩余Cu~(2+)质量浓度降至0.35 mg/L以下,达到GB 21900—2008《电镀污染物排放标准》(小于0.5 mg/L)的要求。     

臭氧氧化法降解聚氯乙烯离心母液废水中3种有机物

以聚氯乙烯离心母液废水中含量较高的3种有机物(聚乙烯醇、异辛醇和α-甲基苯乙烯)作为目标物,考察臭氧氧化工艺对3种有机物的去除效果,同时考察反应时间、臭氧投加量和初始pH对处理效果的影响。实验结果表明,臭氧氧化处理3种废水的最佳反应时间和臭氧投加量分别为:聚乙烯醇25 min,136 mg/L;异辛醇60min,312 mg/L;α-甲基苯乙烯60 min,32 mg/L。在此条件下,3种有机物的去除率分别为98%、85%和95%。此外,碱性条件有助于臭氧氧化工艺对3种有机物的降解。产物分析结果表明,经臭氧氧化,聚乙烯醇断链后进一步反应生成了草酸单乙酯,异辛醇和α-甲基苯乙烯分别生成了和苯乙酮。     

碱激发胶凝材料及其固化Pb^2＋的试验研究

对碱激胶凝材料（碱-偏高岭土、碱-矿渣和碱-粉煤灰）与水-水泥体系固化Ph^2＋进行了试验研究,其中水-水泥体系为对比样。结果表明：对于相同稠度的碱激发胶凝材料,即使Pb^2＋含量达到2．4％,除了碱-粉煤灰的抗压强度略低外,其他都达到30MPa以上,满足填埋或做建筑基材的使用要求;与水泥相比,碱激发胶凝材料能显著降低重金属离子（Ph^2＋）浸出浓度,其规律性与其NH4交换容量大小的规律性一致,与其固化体的抗压强度的大小没有相关性。     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Structure and thermal stability of toxic chromium(VI) species doped onto TiO2 powders through heat treatment

Chromium(VI)-containing sorbents in the form of sludge or solid residue from treatment processes are often landfilled or used as fill materials, therefore the long-term stability of metal binding is important. The reduction of Cr(VI)–Cr(III) through heat treatment may be a useful detoxification method. After heating at 500, 900, 1000, and 1100 °C for 4 h, the transformation of chemical states of chromium on 105 °C-dried, 7.9% Cr(VI)-doped TiO₂ powders was studied on the basis of surface area measurements, scanning electron microscopy (SEM) images, X-ray diffraction (XRD), and extended X-ray absorption fine structure (EXAFS) spectra. It was shown that Cr(VI) was reduced to Cr(III) in the Cr(VI)-doped samples after heating within 500–900 °C. The present results also suggested that the chromium octahedral was bridged to the titanium tetrahedral and was incorporated in TiO₂ minerals formed after 1000 °C treatment.