超滤处理含聚污水过程中通量衰减机理的研究

研究了超滤处理含聚合物污水过程中操作压力、膜面流速、聚合物浓度、料液流变性、阻力等影响因素对膜通量的影响,并进行理论分析,揭示了通量衰减机理.研究结果表明,通量衰减的机理是聚合物的浓差极化和凝胶层的形成,其次是原油和无机物对膜孔的堵塞.     

分体式膜-生物反应器在废水处理中的工艺条件

对分体式膜-生物反应器(RMBR)处理废水进行了研究.进水COD_Cr:312～584mg/L,RMBR的出水CODCr在运行4d后＜15 mg/L并稳定.向生物反应器添加0.5g/L(混合液)的粉末活性炭(PAC)后出水COD_Cr＜4.22mg/L.膜侧污水流速在0.9～1.9m/s范围内,临界膜通量随膜侧污水流速的增大而增大.添加PAC,组合添加PAC和Al₂(SO₄)₃·18 H₂O均可有效提高临界膜通量.在膜侧流速1.9m/s的条件下,临界膜通量从72L/(m²·h)分别增至76L/(m²·h)和81 L/(m²·h)在22℃～30℃范围内,每升高1℃可提高膜通量1.9%.在连续运行100d中,RMBR可在无任何物理,化学清洗的条件下运行14d而透膜压力无增大,膜通量不降低.对于已污染的膜,水清洗、水碱共间清洗、水碱酸共同清洗可分别恢复至新膜膜通量的47%、83%、94%.     

利用玉米浸泡液产电的微生物燃料电池研究

以玉米淀粉生产过程中的浸泡液（玉米浸泡液）作为接种液和基质,利用“三合一”膜电极的单室空气阴极微生物燃料电池进行试验,采用在线监测电压和废水分析方法对产电功率和化学需氧量（COD）、氨氮进行测定,探讨高COD、高氨氮有机废水产电及废水处理的可行性.结果表明,经过94 d（1个周期）的连续运行（固定外电阻为1 000 Ω）,17 d时输出电压达到最大（525.0 mV）,稳定期最大输出功率可达169.6 mW/m²,此时电池相应的电流密度为440.2 mA/m²,内阻约为350 Ω,开路电压619.5 mV;但燃料电池电子利用效率较低（库仑效率为1.6%）;1个周期结束时浸泡液的COD去除率达到51.6%,氨氮去除率25.8%.本试验利用玉米浸泡液成功获得电能,同时对浸泡液有效地进行了处理,为其资源化利用提供新途径.     

膜生物反应器中进水组成对膜污染的影响

研究了膜生物反应器中进水组成对膜污染的影响. 结果表明, 相对于正常组成来说进水中限氮或限磷引起的膜污染程度更重, 尤以进水中限氮时更为严重. 系统缺氮或缺磷时, 污泥絮体的相对憎水性和膜的憎水性增加, 使得膜和污泥之间的憎水相互作用增强, 加速了污染物在膜表面的沉积和/或吸附. 另外, 进水中限氮或限磷时, 污泥中丝状菌的数量增加, 把颗粒污泥捆扎、束缚在其立体网状结构中, 滤层结构更加致密, 孔隙度减小, 增加了膜污染阻力; 丝状菌的作用还在于它们能够将污染物牢牢地缠绕、固定在膜表面, 加强了膜表面污染物抵御曝气的水力冲刷作用的能力, 从而也加速了膜污染.     

蠕虫在膜生物反应器和活性污泥法中的污泥减量研究

通过长达345d的中试规模试验,研究比较了蠕虫在膜生物反应器(MBR)和活性污泥法(CAS)的生长状况及其导致的污泥减量效果.CAS中的蠕虫生长状况明显优于MBR的蠕虫生长状况.MBR曝气池中平均蠕虫密度(10条·mg-1)远低于CAS曝气池中平均蠕虫密度(71条·mg-1),并且CAS中蠕虫连续保持高密度(>30条·mg-1)生长达172d.CAS中红斑瓢体虫和仙女虫交替成为优势蠕虫.蠕虫生长对MBR的污泥产率(0 40kg·kg-1)和污泥沉降性能(污泥沉降指数133mL·g-1)影响很小,但却能显著减少CAS的污泥产率(0 17kg·kg-1)和改善污泥沉降性能(污泥沉降指数为60mL·g-1).仙女虫比红斑瓢体虫能更大地减少污泥产量和更好地改善污泥沉降性能.蠕虫生长不影响MBR的COD去除率和出水水质,但却显著影响CAS的COD去除率和出水水质.     

反渗透膜面细菌胞外多聚物提取方法研究

城市污水脱盐系统的反渗透(RO)膜面生物污堵问题严重影响了该技术的稳定运行,解析生物污堵机理的关键因素是微生物胞外多聚物(EPS)特征分析,然而目前细菌EPS提取方法多样,无统一标准,制约了EPS分析的可靠性和可对比性.基于此,本文以再生水厂RO膜面污堵物中分离的细菌为对象,采用水浴、超声、离子树脂、碱液4种方法提取EPS,以DOC和DNA含量表征提取的EPS总量和提取过程细胞破裂程度.结果表明,45℃水浴法不造成细胞破裂,提取总量多,是一种有效的提取方法.进一步对比不同提取时间条件下EPS溶液中多糖和蛋白含量变化,以及分子量、荧光特征等,综合认为提取1 h时,提取的EPS中多糖与蛋白相对含量稳定,不同分子量化合物均溶于水中,能客观地反映EPS特征.研究表明,45℃水浴1 h可以作为细菌EPS提取的适用方法应用.     

臭氧耦合陶瓷膜过滤对膜性能及出水消毒副产物的影响

利用臭氧（O₃）-陶瓷膜过滤（CMF）处理常规工艺出水,研究了不同O₃-CMF耦合方式对膜性能和消毒副产物（DBPs）的影响.结果表明,与单独CMF相比,异位O₃-CMF和原位O₃-CMF均可以有效缓解膜污染,原位O₃-CMF控制效果最佳.异位O₃-CMF对进水（常规工艺出水） DOC去除率（26.25%）略高于原位O₃-CMF（22.31%）,但是其SUVA去除率（83.91%）明显低于原位O₃-CMF（93.10%）.羟基自由基（·OH）生成特征表明原位O₃-CMF可促进O₃产生更多的·OH.在O₃、·OH氧化和陶瓷膜截留协同作用下,异位O₃-CMF和原位O₃-CMF出水中总荧光响应强度和相对分子质量大于0.3×10³,有机物含量降低,进而使得出水中含碳消毒副产物（C-DBPs）生成量分别降低了21.86%和32.35%,含氮消毒副产物（N-DBPs）生成量分别降低了16.16%和19.13%.但O₃和·OH氧化后生成的小分子有机物因难以被CM截留导致其在出水中含量增加,进而增加了卤代酮（HKs）、水合氯醛（CH）和三卤硝基甲烷（THNMs）的产生.本研究对于不同O₃-CMF方式下O₃与CM的协同机制的探讨,改善膜性能和提升DBPs前体物的去除具有一定指导意义.     

Potassium carbonate-based ternary transition temperature mixture (deep eutectic analogues) for CO2 absorption: Characterizations and DFT analysis

•Addition of hindered amine increased thermal stability and viscosity of TTTM. •Addition of hindered amine improved the CO₂ absorption performance of TTTM. •Good the CO₂ absorption of recycled solvents after two regenerations. •Important role of amine group in CO₂ absorption of TTTM confirmed by DFT analysis. Is it possible to improve CO₂ solubility in potassium carbonate (K₂CO₃)-based transition temperature mixtures (TTMs)? To assess this possibility, a ternary transition-temperature mixture (TTTM) was prepared by using a hindered amine, 2-amino-2-methyl-1,3-propanediol (AMPD). Fourier transform infrared spectroscopy (FT-IR) was employed to detect the functional groups including hydroxyl, amine, carbonate ion, and aliphatic functional groups in the prepared solvents. From thermogravimetric analysis (TGA), it was found that the addition of AMPD to the binary mixture can increase the thermal stability of TTTM. The viscosity findings showed that TTTM has a higher viscosity than TTM while their difference was decreased by increasing temperature. In addition, Eyring’s absolute rate theory was used to compute the activation parameters (ΔG*, ΔH*, and ΔS*). The CO₂ solubility in liquids was measured at a temperature of 303.15 K and pressures up to 1.8 MPa. The results disclosed that the CO₂ solubility of TTTM was improved by the addition of AMPD. At the pressure of about 1.8 MPa, the CO₂ mole fractions of TTM and TTTM were 0.1697 and 0.2022, respectively. To confirm the experimental data, density functional theory (DFT) was employed. From the DFT analysis, it was found that the TTTM+ CO₂ system has higher interaction energy (|ΔE |) than the TTM+ CO₂ system indicating the higher CO₂ affinity of the former system. This study might help scientists to better understand and to improve CO₂ solubility in these types of solvents by choosing a suitable amine as HBD and finding the best combination of HBA and HBD.     

Transparent exopolymer particles (TEPs)-associated protobiofilm: A neglected contributor to biofouling during membrane filtration

• Bacteria could easily and quickly attached onto TEP to form protobiofilms. • TEP-protobiofilm facilitate the transport of bacteria to membrane surface. • More significant flux decline was observed in the presence of TEP-protobiofilms. • Membrane fouling shows higher sensitivity to protobiofilm not to bacteria level. Transparent exopolymer particles (TEPs) are a class of transparent gel-like polysaccharides, which have been widely detected in almost every kind of feed water to membrane systems, including freshwater, seawater and wastewater. Although TEP have been thought to be related to the membrane fouling, little information is currently available for their influential mechanisms and the pertinence to biofouling development. The present study, thus, aims to explore the impact of TEPs on biofouling development during ultrafiltration. TEP samples were inoculated with bacteria for several hours before filtration and the formation of “protobiofilm” (pre-colonized TEP by bacteria) was examined and its influence on biofouling was determined. It was observed that the bacteria can easily and quickly attach onto TEPs and form protobiofilms. Ultrafiltration experiments further revealed that TEP-protobiofilms served as carriers which facilitated and accelerated transport of bacteria to membrane surface, leading to rapid development of biofouling on the ultrafiltration membrane surfaces. Moreover, compared to the feed water containing independent bacteria and TEPs, more flux decline was observed with TEP-protobiofilms. Consequently, it appeared from this study that TEP-protobiofilms play a vital role in the development of membrane biofouling, but unfortunately, this phenomenon has been often overlooked in the literature. Obviously, these findings in turn may also challenge the current understanding of organic fouling and biofouling as membrane fouling caused by TEP-protobiofilm is a combination of both. It is expected that this study might promote further research in general membrane fouling mechanisms and the development of an effective mitigation strategy.     

加油站地下储油罐压力管理系统的相关研究

在当前普遍采用的加油站真空辅助式第二阶段油气回收系统中,为了避免回收到地下储油罐中的油气再次通过P/V阀排空,必须对其中气相空间的压力实施有效控制。从国外的发展情况来看,地下储油罐的压力管理系统主要分为基于膜分离技术、基于弹性气囊和基于活性炭吸附三大类,其中膜法油气回收装置在国内已经得到了较多关注。首次系统介绍了气囊式压力管理系统的工作原理及其主要结构设计,具体包括管线布局、钢制压力容器壳体、位于容器顶部封头上的接口组件和全部位于容器内的气囊等;同时对另外一种可行方案进行了分析。