Spatial Characterization and Prioritization of Heavy Metal Contaminated Soil-Water Resources in Peri-Urban Areas of National Capital Territory (NCT), Delhi

Due to rapid industrialization and urbanization during last two decades, contamination of soils by heavy metals is on an increase globally. Lands under peri-urban agriculture are the worst affected. In NCT, Delhi about 14.4% of land area is chemically degraded. In order to take care of this problem, recently the Supreme Court of India ordered to shift various non-confirming (about 39,000 units) industries to regions outside NCT, Delhi. However in spite of this, there have been several reports and parliamentary debates on the phyto-toxicity and extensive accumulation of heavy metals in the region. Literature review revealed that the basis of these debates is a few studies on some point locations in/around Delhi. It was further observed that information on the distribution and extent of heavy metal pollution problem in the region was completely missing. The present study was thus basically aimed at assessing the spatial distribution/extent and type of heavy metal pollution in the study area, for enabling future designing of appropriate site-specific management measures by the decision makers.For this, detailed spatial information on bio-available heavy metal concentrations in the soils and surface/sub-surface waters of NCT (Delhi) was generated through actual soil/water surveys, standard laboratory methods and GIS techniques. The study showed that concentration of all micronutrients (viz. Zn: 0.05–0.18 ppm; Cu: in traces; Fe: 0–0.5 ppm; and Mn: 0–1.2 ppm) and most heavy metals (viz. Ni: 0–0.7 ppm; Pb: 0–0.15 ppm and Cd: in traces) in the surface/sub-surface irrigation waters were well within permissible limits. However Cr concentrations in irrigation waters of Alipur and Shahdara blocks were far above their maximum permissible limit of 1 ppm. It was further observed that Ni and Cr concentrations in the drinking waters of almost entire test area were far above maximum permissible levels of 0.02 and 0.01 ppm, respectively. Bio-available concentrations of several heavy metals (viz. Pb: 0.1–2 ppm; Cd: traces; Ni: 0.05–2 ppm and Cr: 0–0.4 ppm) in the study area soils were also observed to be well within the maximum permissible limits. However there were point Cu contaminations (5–10 ppm) in the sewage-sludge amended soils of vegetable growing areas near south Shahdara block. This was attributed to increased Cu availability due to oxidized acidic conditions generated by over-irrigation of agricultural lands. Available Mn concentrations in Kanjhawala, western Najafgarh and Alipur soils were also observed to be above maximum permissible limit of 10 ppm. This was observed to be mainly due to the geology (i.e. presence of Mn rich sedimentary rocks) and prevalence of reduced acidic conditions, due to paddy cultivation, in these areas. It was further observed that there is acute zinc (Zn) deficiency (< 0.6 ppm) in paddy growing soils of north Kanjhawala, Alipur and some parts of Najafgarh and Shahdara blocks due to extensive leaching of available Zn fractions to lower soil horizons. Similar available Zn deficiencies in high pH (8.5) soils of areas around Bamnoli village in E-Najafgarh block were also observed.     

Trace Metal Levels in Mussels (Mytilus Galloprovincialis L. 1758) from Turkish Aegean Sea Coast

Bio-monitoring of some heavy metal levels (Cd, Pb, Zn, Cu) in whole edible soft parts of Mytilus galloprovincialis (L. 1758) was conducted in Turkish Aegean Sea coast during the period of September 2002–August 2003 seasonally. Moreover, some physico-chemical environmental parameters, also have been analysed in the same region. The values of some physico-chemical environmental parameters in coastal waters of Turkish Aegean Sea were changed between; 9.0–27.0 ^∘C for temperature, 31.93–40.45 psu for salinity, 7.35–8.48 for pH and 4.05–9.50 mg/l for dissolved oxygen. The levels of trace elements in whole edible soft parts including interstitial fluids of Mediterranean mussels M. galloprovincialis (L. 1758), sampled from 6 different regions of Turkish Aegean Sea coast have ranged between; 0.04–0.52 μg Cd/g wet weight, 0.49–1.72 μg Pb/g w.w., 0.95–1.85 Cu/g w.w., 16.11–37.15 μg Zn/g w.w. The highest values for all trace metals (Cd, Pb, Zn, Cu) were measured in inner part of Izmir Bay (station 3) and lowest in Sigacik and Gulluk Bay (station 5, 6). Generally heavy metal levels are lower than the results in soft mussel tissues reported from Mediterranean regions.     

Characterization and Identification of the Sources of Chromium, Zinc, Lead, Cadmium, Nickel, Manganese and Iron in Pm10 Particulates at the Two Sites of Kolkata, India

Monitoring of ambient PM₁₀ (particulate matter which passes through a size selective impactor inlet with a 50% efficiency cut-off at 10 μm aerodynamic diameter) has been done at residential (Kasba) and industrial (Cossipore) sites of an urban region of Kolkata during November 2003 to November 2004. These sites were selected depending on the dominant anthropogenic activities. Metal constituents of atmospheric PM₁₀ deposited on glass fibre filter paper were estimated using Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES). Chromium (Cr), zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), manganese (Mn) and iron (Fe) are the seven toxic trace metals quantified from the measured PM₁₀ concentrations. The 24 h average concentrations of Cr, Zn, Pb, Cd, Ni, Mn and Fe from ninety PM₁₀ particulate samples of Kolkata were found to be 6.9, 506.1, 79.1, 3.3, 7.4, 2.4 and 103.6 ng/m³, respectively. The 24 h average PM₁₀ concentration exceeded national ambient air quality standard (NAAQS) as specified by central pollution control board, India at both residential (Kasba) and industrial (Cossipore) areas with mean concentration of 140.1 and 196.6 μg/m³, respectively. A simultaneous meteorology study was performed to assess the influence of air masses by wind speed, wind direction, rainfall, relative humidity and temperature. The measured toxic trace metals generally showed inverse relationship with wind speed, relative humidity and temperature. Factor analysis, a receptor modeling technique has been used for identification of the possible sources contributing to the PM₁₀. Varimax rotated factor analysis identified four possible sources of measured trace metals comprising solid waste dumping, vehicular traffic with the influence of road dust, road dust and soil dust at residential site (Kasba), while vehicular traffic with the influence of soil dust, road dust, galvanizing and electroplating industry, and tanning industry at industrial site (Cossipore).     

Acid sulfate soils and human health—A Millennium Ecosystem Assessment

Acid sulfate soils have been described as the “nastiest soils on earth” because of their strong acidity, increased mobility of potentially toxic elements and limited bioavailability of nutrients. They only cover a small area of the world's total problem soils, but often have significant adverse effects on agriculture, aquaculture and the environment on a local scale. Their location often coincides with high population density areas along the coasts of many developing countries. As a result, their negative impacts on ecosystems can have serious implications to those least equipped for coping with the low crop yields and reduced water quality that can result from acid sulfate soil disturbance. The Millennium Ecosystem Assessment called on by the United Nations in 2000 emphasised the importance of ecosystems for human health and well-being. These include the service they provide as sources of food and water, through the control of pollution and disease, as well as for the cultural services ecosystems provide. While the problems related to agriculture, aquaculture and the environment have been the focus of many acid sulfate soil management efforts, the connection to human health has largely been ignored. This paper presents the potential health issues of acid sulfate soils, in relation to the ecosystem services identified in the Millennium Ecosystem Assessment. It is recognised that significant implications on food security and livelihood can result, as well as on community cohesiveness and the spread of vector-borne disease. However, the connection between these outcomes and acid sulfate soils is often not obvious and it is therefore argued that the impact of such soils on human well-being needs to be recognised in order to raise awareness among the public and decision makers, to in turn facilitate proper management and avoid potential human ill-health.     

On causes of gigantism in herbaceous plants

Landscape-geochemical features providing for manifestation of gigantism in herbaceous plants have been revealed in natural habitats in the south of Sakhalin and Kunashir islands. Tall herb assemblages have proved to be associated with geochemical landscapes characterized by reducing (gley or hydrogen sulfide) conditions and increased contents of petroleum hydrocarbons and some trace elements (total and movable forms). A hypothesis is put forward that gigantism in herbaceous plants is manifested in zones of active faults, which serve as a kind of conduits supplying endogenous heat, matter, and water to the root systems.     

微量金属元素及其配合物对厨余垃圾甲烷发酵的影响

生物可利用的微量金属元素不仅能够保证污染物以最大的速率转化,而且还可以使某些特殊的转化得以发生,并提高微生物对有毒污染物质的耐受能力。在研究厨余垃圾总固体浓度(total solid, TS)、接种量和C/N比对厨余垃圾厌氧发酵影响的基础上,重点探讨微量金属元素钴及其配合物丝氨酸对厨余垃圾厌氧发酵甲烷产量及关键酶含量的影响。结果表明,当TS为0.5%、接种污泥量为100 mL/L和C/N比为20∶1时,厨余垃圾厌氧发酵的甲烷产率较高,为367 mL/g COD;添加2 μmol/L的微量金属元素钴-配合物丝氨酸时,甲烷产率则提高到432 mL/g COD,相应地,辅酶M的含量由空白实验的41.21 μmol/g VSS提高到54.64 μmol/g VSS,辅酶F₄₂₀的含量由0.31 μmol/g VSS提高到0.48 μmol/g VSS。     

Immobilization of Pb(II), Cd(II) and Ni(II) ions on kaolinite and montmorillonite surfaces from aqueous medium

The present study investigates the immobilization of Pb(II), Cd(II) and Ni(II) on clays (kaolinite and montmorillonite) in aqueous medium through the process of adsorption under a set of variables (concentration of metal ion, amount of clay, pH, time and temperature of interaction). Increasing pH favours the removal of metal ions till they are precipitated as the insoluble hydroxides. The uptake is rapid with maximum adsorption being observed within 180 min for Pb(II) and Ni(II) and 240 min for Cd(II). A number of available models like the Lagergren pseudo first-order kinetics, second-order kinetics, Elovich equation, liquid film diffusion and intra-particle diffusion are utilized to evaluate the kinetics and the mechanism of the immobilization interactions. Two isotherm equations due to Langmuir and Freundlich showed good fits with the experimental data. Kaolinite and montmorillonite have considerable Langmuir monolayer capacity with respect to Pb(II), Cd(II) and Ni(II), the values being in the range of 6.8-11.5mg/g (kaolinite) and 21.1-31.1mg/g (montmorillonite). The Freundlich adsorption capacity follows a similar order. The thermodynamics of the immobilization process indicates the same to be exothermic with Pb(II) and Ni(II), but endothermic with Cd(II). The interactions with Pb(II) and Ni(II) are accompanied by decrease in entropy and Gibbs energy while the endothermic immobilization of Cd(II) is supported by an increase in entropy and an appreciable decrease in Gibbs energy. The results have established good potentiality for kaolinite and montmorillonite to remove heavy metals like Pb(II), Cd(II) and Ni(II) from aqueous medium through adsorption-mediated immobilization.     

Assessment of the phytoextraction potential of high biomass crop plants

A hydroponic screening method was used to identify high biomass crop plants with the ability to accumulate metals. Highest values of shoot accumulation were found in maize cv. Ranchero, rapeseed cv. Karat, and cardoon cv. Peralta for Pb (18 753 mg kg(-1)), Zn (10 916 mg kg(-1)), and Cd (242 mg kg(-1)), respectively. Subsequently, we tested the potential of these three cultivars for the phytoextraction of a metal spiked compost, finding out that, in cardoon and maize plants, increasing Zn and Cd concentrations led to lower values of root and shoot DW. By contrast, rapeseed shoot growth was not significantly affected by Cd concentration. Finally, a metal polluted soil was used to check these cultivars' phytoextraction capacity. Although the soil was phytotoxic enough to prevent the growth of cardoon and rapeseed plants, maize plants phytoextracted 3.7 mg Zn pot(-1). We concluded that the phytoextraction performance of cultivars varies depending on the screening method used.     

Long-term survey of heavy-metal pollution, biofilm contamination and diatom community structure in the Riou Mort watershed, South-West France

In a metal-polluted stream in the Riou Mort watershed in SW France, periphytic biofilm was analyzed for diatom cell densities and taxonomic composition, dry weight and metal bio-accumulation (cadmium and zinc). Periphytic diatom communities were affected by the metal but displayed induced tolerance, seen through structural impact (dominance of small, adnate species) as well as morphological abnormalities particularly in the genera Ulnaria and Fragilaria. Species assemblages were characterized by taxa known to occur in metal-polluted environments, and shifts in the community structure expressed seasonal patterns: high numbers of Eolimna minima, Nitzschia palea and Pinnularia parvulissima were recorded in Summer and Autumn, whereas the species Surirella brebissonii, Achnanthidium minutissimum, Navicula lanceolata and Surirella angusta were dominant in Winter and Spring. Commonly used indices such as the Shannon diversity index and Specific Pollution Sensitivity Index reflected the level of pollution and suggest seasonal periodicity, the lowest diversities being observed in Summer.     

污泥掺烧对燃煤电厂痕量元素排放特性影响

采用EPAMethod29方法、冷原子吸收光谱法和电感耦合等离子体质谱法采集和分析一台超低排放燃煤机组污泥掺烧前后的原燃料、烟气和副产物样品中各痕量元素浓度,研究污泥掺烧对燃煤电厂痕量元素排放特性的影响.结果表明:污泥中富含Zn、Cu元素,浓度分别是煤样中的18.81倍和17.64倍.污泥掺烧使掺配后入炉煤中痕量元素含量普遍升高.污泥掺烧前后整个系统、锅炉系统和全流程大气污染控制设施的痕量元素质量平衡率均在可接受范围内.污泥掺烧对痕量元素的分布特征无明显影响,随粉煤灰排放是痕量元素的主要排放去向.通过烟囱排放到大气环境的痕量元素排放量占比很小,不超过0.43%.污泥掺烧前后SCR入口烟气中痕量元素除Hg外主要以颗粒态形式存在.污泥掺烧后各痕量元素在粉煤灰和底渣中的相对富集系数未显著改变.经过全流程大气污染控制设施协同控制后,污泥掺烧前后烟囱总排口痕量元素排放浓度分别为0～12.76,0～14.97μg/m³.污泥掺烧后痕量元素排放浓度均满足美国燃煤发电机组有害大气污染物排放标准、上海市燃煤耦合污泥电厂大气污染排放标准和生态环境部生活垃圾焚烧污染控制标准的限值要求....