Utilization of MSWI fly ash as partial cement or sand substitute with focus on cementing efficiency and health risk assessment

• Washed MSWI fly ash was used as partial cement or sand substitute. • Sand replacing is beneficial for strength, while cement replacement reduces strength. • Cementing efficiency factor and mortar pore structure explain the strength results. • Health risk assessment was conducted for MSWI fly ash blended cement mortar. • CR and HI contributed by different exposures and heavy metals were analyzed. The strength of cement substituted mortar decreases with the increase in fly ash amount, whereas the strength increases when the fly ash is blended as sand substitute. A mortar with highest strength (compressive strength= 30.2 Mpa; flexural strength= 7.0 Mpa) was obtained when the sand replacement ratio was 0.75%. The k value (cementing efficiency) of fly ash varied between 0.36 and 0.15 for the fly ash fraction in binder between 5% and 25%. The k values of fly ash used for sand replacement were all significantly above that used for cement substitution. The macropores assigned to the gaps between particles decreased when the fly ash was used as sand replacement, providing an explanation for the strength enhancement. The waste-extraction procedure (toxicity-sulphuric acid and nitric acid method (HJ/T 299-2007)) was used to evaluate metal leaching, indicating the reuse possibility of fly ash blended mortar. For the mortar with the mass ratio of fly ash to binder of 0.5%, the carcinogenic risks (CR) and non-carcinogenic hazard quotient (HQ) in sensitive scenario for blended mortar utilization were 9.66 × 10^-7 and 0.06, respectively; these results were both lower than the threshold values, showing an acceptable health risk. The CR (9.89 × 10^-5) and HQ (3.89) of the non-sensitive scenario for fly ash treatment exceeded the acceptable threshold values, indicating health risks to onsite workers. The main contributor to the carcinogenic and non-carcinogenic risk is Cr and Cd, respectively. The CR and HQ from inhalation was the main route of heavy metal exposure.     

Diffusive gradients in thin films using molecularly imprinted polymer binding gels for in situ measurements of antibiotics in urban wastewaters

• Selective molecularly imprinted polymer (MIP) binding gel was prepared. • MIP-DGT showed excellent uptake performance for antibiotics. • In situ measurement of antibiotics in wastewaters via MIP-DGT was developed. • The MIP-DGT method was robust, reliable, and highly sensitive. Urban wastewater is one of main sources for the introduction of antibiotics into the environment. Monitoring the concentrations of antibiotics in wastewater is necessary for estimating the amount of antibiotics discharged into the environment through urban wastewater treatment systems. In this study, we report a novel diffusive gradient in thin films (DGT) method based on molecularly imprinted polymers (MIPs) for in situ measurement of two typical antibiotics, fluoroquinolones (FQs) and sulfonamides (SAs) in urban wastewater. MIPs show specific adsorption toward their templates and their structural analogs, resulting in the selective uptake of the two target antibiotics during MIP-DGT deployment. The uptake performance of the MIP-DGTs was evaluated in the laboratory and was relatively independent of solution pH (4.0–9.0), ionic strength (1–750 mmol/L), and dissolved organic matter (DOM, 0–20 mg/L). MIP-DGT samplers were tested in the effluent of an urban wastewater treatment plant for field trials, where three SA (sulfamethoxazole, sulfapyridine, and trimethoprim) and one FQ (ofloxacin) antibiotics were detected, with concentrations ranging from 25.50 to 117.58 ng/L, which are consistent with the results measured by grab sampling. The total removal efficiency of the antibiotics was 80.1% by the treatment plant. This study demonstrates that MIP-DGT is an effective tool for in situ monitoring of trace antibiotics in complex urban wastewaters.     

Mapping the Spatial Variability of Plant Diversity in a Tropical Forest: Comparison of Spatial Interpolation Methods

Knowledge of the spatial distribution of plant species is essential to conservation and forest managers in order to identify high priority areas such as vulnerable species and habitats, and designate areas for reserves, refuges and other protected areas. A reliable map of the diversity of plant species over the landscape is an invaluable tool for such purposes. In this study, the number of species, the exponent Shannon and the reciprocal Simpson indices, calculated from 141 quadrat sites sampled in a tropical forest were used to compare the performance of several spatial interpolation techniques used to prepare a map of plant diversity, starting from sample (point) data over the landscape. Means of mapped classes, inverse distance functions, kriging and co-kriging, both, applied over the entire studied landscape and also applied within vegetation classes, were the procedures compared. Significant differences in plant diversity indices between classes demonstrated the usefulness of boundaries between vegetation types, mapped through satellite image classification, in stratifying the variability of plant diversity over the landscape. These mapped classes, improved the accuracy of the interpolation methods when they were used as prior information for stratification of the area. Spatial interpolation by co-kriging performed among the poorest interpolators due to the poor correlation between the plant diversity variables and vegetation indices computed by remote sensing and used as covariables. This indicated that the latter are not suitable covariates of plant diversity indices. Finally, a within-class kriging interpolator yielded the most accurate estimates of plant diversity values. This interpolator not only provided the most accurate estimates by accounting for the indices' intra-class variability, but also provided additional useful interpretations of the structure of spatial variability of diversity values through the interpretation of their semi-variograms. This additional role was found very useful in aiding decisions in conservation planning.     

Spatial Characterization and Prioritization of Heavy Metal Contaminated Soil-Water Resources in Peri-Urban Areas of National Capital Territory (NCT), Delhi

Due to rapid industrialization and urbanization during last two decades, contamination of soils by heavy metals is on an increase globally. Lands under peri-urban agriculture are the worst affected. In NCT, Delhi about 14.4% of land area is chemically degraded. In order to take care of this problem, recently the Supreme Court of India ordered to shift various non-confirming (about 39,000 units) industries to regions outside NCT, Delhi. However in spite of this, there have been several reports and parliamentary debates on the phyto-toxicity and extensive accumulation of heavy metals in the region. Literature review revealed that the basis of these debates is a few studies on some point locations in/around Delhi. It was further observed that information on the distribution and extent of heavy metal pollution problem in the region was completely missing. The present study was thus basically aimed at assessing the spatial distribution/extent and type of heavy metal pollution in the study area, for enabling future designing of appropriate site-specific management measures by the decision makers.For this, detailed spatial information on bio-available heavy metal concentrations in the soils and surface/sub-surface waters of NCT (Delhi) was generated through actual soil/water surveys, standard laboratory methods and GIS techniques. The study showed that concentration of all micronutrients (viz. Zn: 0.05–0.18 ppm; Cu: in traces; Fe: 0–0.5 ppm; and Mn: 0–1.2 ppm) and most heavy metals (viz. Ni: 0–0.7 ppm; Pb: 0–0.15 ppm and Cd: in traces) in the surface/sub-surface irrigation waters were well within permissible limits. However Cr concentrations in irrigation waters of Alipur and Shahdara blocks were far above their maximum permissible limit of 1 ppm. It was further observed that Ni and Cr concentrations in the drinking waters of almost entire test area were far above maximum permissible levels of 0.02 and 0.01 ppm, respectively. Bio-available concentrations of several heavy metals (viz. Pb: 0.1–2 ppm; Cd: traces; Ni: 0.05–2 ppm and Cr: 0–0.4 ppm) in the study area soils were also observed to be well within the maximum permissible limits. However there were point Cu contaminations (5–10 ppm) in the sewage-sludge amended soils of vegetable growing areas near south Shahdara block. This was attributed to increased Cu availability due to oxidized acidic conditions generated by over-irrigation of agricultural lands. Available Mn concentrations in Kanjhawala, western Najafgarh and Alipur soils were also observed to be above maximum permissible limit of 10 ppm. This was observed to be mainly due to the geology (i.e. presence of Mn rich sedimentary rocks) and prevalence of reduced acidic conditions, due to paddy cultivation, in these areas. It was further observed that there is acute zinc (Zn) deficiency (< 0.6 ppm) in paddy growing soils of north Kanjhawala, Alipur and some parts of Najafgarh and Shahdara blocks due to extensive leaching of available Zn fractions to lower soil horizons. Similar available Zn deficiencies in high pH (8.5) soils of areas around Bamnoli village in E-Najafgarh block were also observed.     

金属粉尘湿法处理系统的设计和除尘效果分析

为改善金属抛光操作人员的工作环境、降低抛光金属粉尘的爆炸风险,设计一种金属粉尘湿法处理系统,并通过建立多相流动数值模型,探究其内部流场特征与金属粉尘运动规律,分析金属粉尘湿法处理系统的除尘效率。研究结果表明:大粒径的金属粉尘直接重力沉降至水槽中;小粒径(PM10)的金属粉尘易随气流进入风道,进而通过水雾脱除;采用洁净进气源,可以有效降低工人操作环境的粉尘浓度;增加细水雾,可以有效提高金属粉尘湿法处理系统的除尘效率,对PM10的除尘效率从30%提升至82%。     

燃煤电厂超低排放气态污染物监测技术综述

介绍了燃煤电厂超低排放气态污染物监测系统的采样系统和分析单元,分析了其各自的优缺点。对稀释抽取式、冷干抽取式和热湿抽取式3种采样方法,以及非分散红外吸收法(NDIR)、非分散紫外吸收法(NDUV)、紫外差分吸收法(DOAS)、紫外荧光法(UVF)和化学发光法(CL)5种分析方法进行对比。结果表明,冷干抽取式+紫外差分法以及稀释抽取式+紫外荧光法+化学发光法可以较好地符合燃煤电厂超低排放监测的要求。     

3种大型海藻对含铅废水的生物吸附研究

运用批吸附技术研究了海带、裙带菜和条斑紫菜对水溶液中Pb2+的吸附特性。结果表明:pH是影响生物吸附的重要因素,海带和裙带菜吸附Pb2+的适宜pH在3~5之间,紫菜吸附Pb2+的最佳pH为4;在20~40℃范围内,3种海藻对Pb2+的生物吸附非常快,40 min达到吸附平衡,动力学数据符合准二级动力学模型;Langmuir和Freundlich模型成功地拟合了平衡数据。热力学分析表明吸附能够自发进行。红外光谱分析表明,羧基是海带和裙带菜吸附Pb2+的主要官能团。实验结果表明,用这3种海藻吸附剂对水溶液中Pb2+具有较好的吸附性能,海带和裙带菜的吸附容量相近,优于紫菜。     

3种浮床植物系统对富营养化水体净化效果研究

研究了风车草(Cyperus alternifolius)、菖蒲(Acorus calamus)和富贵竹(Dracaena sanderiana)3种浮床植物系统对富营养化水体净化效果,试验共持续35 d。结果表明,在水温24～30℃条件下,风车草和菖蒲生长良好,生物量大,而富贵竹生长较差,生物量增加少;3种植物对NH_4~+-N的去除率分别为76.8%、85.5%和53.6%,对TN的去除率分别为69.1%、66.2%和54.4%,对TP的去除率分别为76.9%、84.6%和61.5%,对PO_4~(3-)-的去除率分别为91.7%、91.7%和75%,对真实色度有明显的去除效果;3种植物对氮磷和真实色度去除效果与对照之间均达到显著差异(P0.05),自然沉淀是浊度去除的主要原因,植物吸收同化作用是NH_4~+-N去除的主要途径,植物吸收是溶解性磷去除的主要途径。试验表明,风车草和菖蒲对富营养化水体中氮磷和真实色度有较好的去除效果,可作为富营养化水体治理的优良物种而推广使用。     

The distribution of Cs, K, Rb and Cs in plants in a Sphagnum-dominated peatland in eastern central Sweden

We record the distribution of ¹³⁷Cs, K, Rb and Cs within individual Sphagnum plants (down to 20 cm depth) as well as ¹³⁷Cs in vascular plants growing on a peatland in eastern central Sweden. In Calluna vulgaris¹³⁷Cs was mainly located within the green parts, whereas Andromeda polifolia, Eriophorum vaginatum and Vaccinium oxycoccos showed higher ¹³⁷Cs activity in roots. Carex rostrata and Menyanthes trifoliata showed variable distribution of ¹³⁷Cs within the plants. The patterns of ¹³⁷Cs activity concentration distribution as well as K, Rb and Cs concentrations within individual Sphagnum plants were rather similar and were usually highest in the capitula and/or in the subapical segments and lowest in the lower dead segments, which suggests continuous relocation of those elements to the actively growing apical part. The ¹³⁷Cs and K showed relatively weak correlations, especially in capitula and living green segments (0-10 cm) of the plant (r = 0.50). The strongest correlations were revealed between ¹³⁷Cs and Rb (r = 0.89), and between ¹³⁷Cs and stable Cs (r = 0.84). This suggests similarities between ¹³⁷Cs and Rb in uptake and relocation within the Sphagnum, but that ¹³⁷Cs differs from K.     

Seasonal and inter-annual variation of Beryllium-7 deposition in birch-tree leaves and grass in the northeast upland area of the Czech Republic

The activity concentrations of Beryllium-7 (⁷Be), a naturally occurring radioisotope produced in the atmosphere, were measured in leaves of birch-trees, above-ground parts of grass, soil and rainwater in the mountain massive Kralicky Sneznik (the northeast of the Czech Republic, altitude about 750 m) in the years of 2005, 2006 and 2007. Dried and ground samples of the plants and soils, and water samples from wet deposition were used to determine the ⁷Be content using a semiconductor gamma spectrometer. The ⁷Be values ranged from 147.0 to 279.6 Bq kg⁻¹, from 48.7 to 740.8 Bq kg⁻¹, from 2.1 to 8.7 Bq kg⁻¹, and from 0.6 to 1.9 Bq kg⁻¹ in birch-tree leaves, grass samples, soils, and rainwater, respectively. Insignificant inter-annual variations but significant increase in the ⁷Be activity concentrations during the spring and summer months were observed in birch-tree leaves and grass samples. The seasonal variation of the ⁷Be concentrations in grass samples correlated (R² = 0.4663 and 0.6489) with precipitation. No similar correlation was found for ⁷Be in birch-tree leaves. Beryllium-7 content in birch-tree leaves and in aerial parts of grass was mainly caused by direct transport of ⁷Be from wet deposition into aerial parts of the observed plants.