铁碳促进O3/H2O2体系深度处理准好氧矿化垃圾床渗滤液尾水中难降解有机物

构建了铁碳-O_3/H_2O_2体系降解矿化垃圾床渗滤液尾水中有机物,并考察了体系O_3、铁碳及H_2O_2投加量、初始pH值和反应时间对铁碳-O_3/H_2O_2体系处理渗滤液尾水的影响.结果表明,在铁碳投加量为3 g·L~(-1),O_3投加量为9.798 mg·min~(-1),H_2O_2投加量为2 mL·L~(-1),初始pH值为3的条件下,反应10 min后,渗滤液尾水的COD和UV_(245)分别从711.96 mg·L~(-1)、0.19下降至295.04 mg·L~(-1)、0.10.类比实验结果表明,铁碳-O_3/H_2O_2体系对渗滤液尾水有机物具有较高的去除率,且可生化性得到提高(BOD/COD从0.04增加至0.40).紫外-可见和三维荧光光谱显示,废水中难降解有机物转化为小分子有机化合物且腐殖质的分子缩合度降低.最后,采用SEM-EDS、XRD和XPS技术对铁碳-O_3/H_2O_2体系的反应机理进行了解析,发现铁碳-O_3/H_2O_2反应的机理为铁碳微电解反应、铁氧化物-H_2O_2非均相芬顿反应、O_3/H_2O_2、铁碳-O_3非均相的高级氧化作用和铁基胶体对有机物的吸附沉淀作用.研究表明,铁碳-O_3/H_2O_2体系是一种能够有效去除矿化垃圾床渗滤液尾水中难降解有机物的方法.     

基于铁锰泥的除砷吸附剂性能比较及吸附机理

为解决反冲洗铁锰泥粉末吸附剂（BSPA）使用后难以泥水分离问题,将除铁锰水厂生物滤池产生的反冲洗泥制成颗粒吸附剂（GA）和磁性粉末吸附剂（MPA）,并对BSPA、GA和MPA的除砷性能进行了比较,通过SEM、TED、XRD、BET、FTIR等技术对3种材料进行了表征,寻找3种吸附剂之间除砷性能差异的根源.结果表明,BSPA、GA和MPA对As （V）的最大吸附容量分别为40.980,5.048,8.694mg/g,改性后的吸附材料GA和MPA对砷的吸附能力下降.BSPA是一种以纤铁矿为主的无定形结构混合物,并混有针铁矿和结晶度差的水铁矿,GA的XRD图谱中出现石英晶体和少量赤铁矿晶体的衍射峰,而MPA的主要成分为结晶程度较高的磁赤铁矿.3种材料中均存在有利于吸附的含羟基官能团.BSPA、MPA和GA的比表面积分别为253.150,238.660,43.803m²/g.物相改变且结晶程度增加、表面羟基减少和比表面积降低是导致GA和MPA的砷吸附容量比BSPA低的主要因素.     

新型Fe3O4@α-MnO2活化过一硫酸盐降解水中偶氮染料

采用两步水热法制备了新型磁性纳米Fe₃O₄@α-MnO₂复合材料作为催化剂,用于活化过一硫酸盐（PMS）产生强氧化性的硫酸根自由基（SO₄^-·）氧化降解偶氮染料活性黑5（RBK5）.采用透射电子显微镜（TEM）,X射线粉末衍射仪（XRD）和振动样品磁强计（VSM）对制备的催化剂进行表征,证明成功合成了纳米α-MnO₂包覆Fe₃O₄形态的Fe₃O₄@α-MnO₂催化剂,催化剂的饱和磁化强度为39.89emu/g.Fe₃O₄@α-MnO₂催化剂活化PMS与单一的Fe₃O₄和α-MnO₂活化PMS相比,具有更高的催化效率,说明铁锰双金属存在协同作用.同时研究了催化剂的投加量、PMS的浓度和初始pH值等各种因素对RBK5的降解效率以及反应动力学的影响.实验结果表明,Fe₃O₄@α-MnO₂催化剂活化PMS降解RBK5的过程符合准一级反应动力学,在催化剂投加量为1.2g/L,PMS的浓度为4mmol/L,初始pH值为7.0,反应时间为60min的情况下,浓度为30mg/L的RBK5的降解效率可达到91%,此时RBK5的降解速率常数也达到最高值0.023min^-1.此外,通过加入自由基淬灭剂甲醇、叔丁醇和硝基苯判断了Fe₃O₄@α-MnO₂/PMS体系中起主要氧化降解作用的活性物种为SO₄^-·.     

近10年中国三大经济区太阳总辐射特征及其与O3、PM2.5的关系

采用中国地面气象观测站网2007~2016年的辐射日值数据集和中国空气质量在线监测平台2014~2016年逐日观测数据,分析了京津冀、长三角和珠三角近10a太阳总辐射年际和季节变化,近3a臭氧日最大8h平均（O_{3_8h_max}）和细颗粒物（PM_2.5）的污染过程频次变化,通过不同因子及其不同强度等级的分型统计,探讨PM_2.5、O_{3_8h_max}与太阳总辐射的关系.结果表明：京津冀近10a太阳总辐射显著上升,京津冀春季和珠三角夏季太阳总辐射显著上升.三大经济区PM_2.5污染过程年频次均呈现逐年递减,且从北到南递减;O₃污染过程年频次时间上呈现先减后增,空间上京津冀多于长三角和珠三角.三大经济区O_{3_8h_max}与太阳总辐射相关系数均在0.71以上,有较强的正相关;而PM_2.5与太阳总辐射的相关性具有区域差异性.三大经济区不同季节不同太阳总辐射下O_{3_8h_max}与PM_2.5的相关关系差异显著,其中京津冀春夏秋三季O_{3_8h_max}与PM_2.5在强太阳总辐射下有较好的正相关,冬季则存在一定的负相关;长三角四季两者相关性均较弱;珠三角夏季两者正相关最为显著;不同PM_2.5浓度下O_{3_8h_max}与太阳总辐射的线性拟合效果较好,体现出较强的正相关关系,各经济区拟合曲线的倾向率均随PM_2.5升高而增大.PM_2.5>75μg/m³时拟合优度均达到最大.     

Mesoporous WO3-graphene photocatalyst for photocatalytic degradation of Methylene Blue dye under visible light illumination

Advanced oxidation technologies are a friendly environmental approach for the remediation of industrial wastewaters. Here, one pot synthesis of mesoporous WO_3 and WO_3-graphene oxide(GO) nanocomposites has been performed through the sol–gel method. Then, platinum(Pt) nanoparticles were deposited onto the WO_3 and WO_3-GO nanocomposite through photochemical reduction to produce mesoporous Pt/WO_3 and Pt/WO_3-GO nanocomposites. X-ray diffraction(XRD) findings exhibit a formation of monoclinic and triclinic WO_3 phases. Transmission Electron Microscope(TEM) images of Pt/WO_3-GO nanocomposites exhibited that WO_3 nanoparticles are obviously agglomerated and the particle sizes of Pt and WO_3 are ~ 10 nm and 20–50 nm, respectively. The mesoporous Pt/WO_3 and Pt/WO_3-GO nanocomposites were assessed for photocatalytic degradation of Methylene Blue(MB) as a probe molecule under visible light illumination.The findings showed that mesoporous Pt/WO_3, WO_3-GO and Pt/WO_3-GO nanocomposites exhibited much higher photocatalytic efficiencies than the pure WO_3. The photodegradation rates by mesoporous Pt/WO_3-GO nanocomposites are 3, 2 and 1.15 times greater than those by mesoporous WO_3, WO_3-GO, and Pt/WO_3, respectively. The key factors of the enhanced photocatalytic performance of Pt/WO_3-GO nanocomposites could be explained by the highly freedom electron transfer through the synergetic effect between WO_3 and GO sheets, in addition to the Pt nanoparticles that act as active sites for O2 reduction, which suppresses the electron hole pair recombination in the Pt/WO_3-GO nanocomposites.     

碳量子点掺杂氮化碳提高的光电化学阴极保护性能研究

目的研究g-C_3N_4/C-Dots-M复合材料的光电化学阴极保护性能。方法采用X射线衍射(XRD)、扫描电子显微镜(SEM)和紫外可见漫反射光谱技术对样品的晶体结构、微观形貌和光吸收性能进行表征。通过电化学测试可见光照射下g-C_3N_4/C-Dots-M复合材料光电极偶联316L不锈钢后的光电化学阴极保护电流密度和电位变化曲线,研究材料的光电化学阴极保护性能。结果可见光照射下,该偶联体系的光致混合电位下降至-0.43 V(vs. Ag/AgCl),光电化学阴极保护电流密度达到4.3μA/cm。结论得益于碳量子点优异的电子传导特性,g-C_3N_4/C-Dots-550复合材料的光电化学阴极保护性能比纯g-C_3N_4的明显增强。该复合材料在光电化学阴极保护方面展现了较大的应用潜力。     

DZ125合金HY3包覆型涂层退除研究

目的 研究化学法退除DZ125合金HY3包覆型涂层。方法 采用真空电弧镀技术（AIP）在定向凝固镍基高温合金DZ125上制备包覆型涂层HY3,利用化学方法完全退除基体上的涂层,通过失重法研究对比1#和2#退除溶液退除HY3涂层和DZ125合金的退除速率,采用扫描电镜（SEM）对退除后的HY3涂层和DZ125基体的微观组织进行观察。结果 经过100 min,2#溶液可以将20 ?m左右的HY3涂层完全退除,采用1#溶液需要超过100 min才能完全退除涂层。两种对DZ125合金的腐蚀性很小,对于同一种合金而言,1#溶液和2#溶液对合金的腐蚀速率比值为1︰13。在1#溶液中,合金与涂层腐蚀速率的比值为1︰87.65;在2#退除溶液中,合金与涂层腐蚀速率的比值为1︰6.81。结论 1#溶液更加适合退除DZ125合金上的HY3涂层。     

典型铅锌矿化区不同土地利用类型土壤重金属污染特征与评价

选取云南者海典型铅锌矿区周边冶炼区（A）、粮食主产区（B）、保护区（C）三个区域土壤为研究对象,分析三个区域内林地（LD）和耕地（GD）土壤pH、总碳（TC）、总氮（TN）、总磷（TP）和5种重金属（Hg、Cd、Pb、Zn、Cu）含量,利用典范对应分析（CCA）研究不同土地利用类型下它们之间的关系,基于系统熵值与重金属生物毒性改进灰色聚类评价法对研究区重金属污染程度进行评价。结果表明,A、B、C三区土壤的5种重金属均超过云南省土壤背景值,且含量A区 > B区 > C区,所有土壤样品Hg、Cd、Pb、Zn、Cu平均含量分别为7.24、1.53、1 794、2 892、210 mg/kg;LD土壤重金属含量普遍高于GD。研究区土壤pH总体呈弱酸性,但A区土壤受矿业活动影响呈弱碱性。TC、TN含量和C/N值均表现出LD大于GD,但TP含量表现为GD显著大于LD （P<0.05）。CCA分析表明LD和GD土壤pH与Cd和Cu呈负相关,与Zn和Pb呈正相关,且pH对重金属含量的影响最大;TC、TP与重金属Cd和Cu在LD土壤中呈正相关,在GD土壤中呈负相关。改进灰色聚类评价结果表明重金属污染程度均表现为LD大于GD;A区污染最严重且均呈重度污染,B区次之,C区污染程度最轻。经比较本文改进的灰色聚类评价法在准确性和灵敏度方面优于传统方法。     

Competitive Retention of Lead and Cadmium on an Agricultural Soil

Lead and cadmium contamination of an agricultural soil has been studied using batch and column experiments. Thermodynamics of theretention phenomena may be represented by a Langmuir isotherm foran aqueous metal concentration up to 100 mg L^-1. First order kinetics with respect to the solid phase yield good predictabilityfor both batch and column experiments. Kinetics and thermodynamics of lead retention predominate over those ofcadmium. As a consequence, lead is preferentially retainedand can even displace sorbed cadmium. In the event of anspill involving both metals, cadmium would move further inthe soil and its aqueous concentration downstream could beeven higher than that of the influent solution, increasingpotential risks. A two-region model has been used to fit all the experimental results. Satisfactory predictions for column experiments are obtained with parameters which are consistent with those obtained for the batch experiments, for which sorption is described by a Langmuir isotherm including competitive retention.     

Bioindicator organisms: Heavy metal pollution evaluation in the Ionian Sea (Mediterranean Sea—Italy)

Trace metal concentrations of mercury, cadmium, lead and chromium in Patella caerulea, and Mullus barbatus were investigated to provide information on pollution of Ionian Sea, since these metals have the highest toxic potential. High chromium levels (0.47–0.97 g g^–1 ww) were registered in limpet samples collected from two station near the Gulf of Taranto, while elevated concentration of mercury (0.31–1.50 g g^–1 ww) were found in mullet specimens from Sicily. The metal concentrations recorded at the clean stations may be considered as useful background levels to which to refer for comparison within the Mediterranean area. On the contrary, the high levels of chromium and mercury found respectively in the areas near the Gulf of Taranto and at Capo Passero being of concern in terms of environmental health need frequent monitoring.