市政污泥用于矿区土壤改良的污染风险评估及配比分析

通过土柱淋溶试验,分析了市政污泥在矿山土壤改良中重金属污染风险,探讨了市政污泥用于矿区土壤改良的可行性,并确定了土壤污泥最佳混掺比例。结果表明:景山高岭土矿区土壤除速效磷含量较高外,其余养分含量分级为四—五级,即"低—很低";市政污泥除速效钾含量较低外,其余养分含量分级均远大于一级"很高";永春污水处理厂污泥为B级农用污泥,可施用于油料作物、果树、饲料作物、纤维作物,不能施用于蔬菜、粮食作物;按各处理配比进行污泥的适量施用造成地下水污染风险较小;综合考虑土壤肥力及重金属污染因素,该矿区最佳土壤、市政污泥干重混掺比为5∶2。     

污泥超高温堆肥过程中DOM结构的光谱分析

为了明确超高温堆肥新工艺在促进腐殖化进程中的优势,采用三维荧光光谱(3D-EEM)等光谱学方法研究了污泥超高温堆肥过程中DOM的结构特征及其变化规律.结果表明,堆体≥80℃的超高温阶段持续5 d(最高温度90℃),50℃以上高温阶段达到22 d,反映了堆肥过程中强烈的微生物代谢活性.E253/E203、SUVA280、S275~295等9个紫外-可见光光谱(UV-Vis)指标在0~23 d变化显著,指出DOM的芳香化和堆肥腐殖化程度逐渐增强.3D-EEM光谱结合荧光区域体积积分技术(FRI)分析指出,DOM中蛋白类物质在超高温堆肥过程的0~6 d几乎完全被降解;腐殖酸和富里酸类物质在0~23 d大量形成,堆肥在高温阶段达到完全腐熟,这与种子发芽指数(GI)在23 d所指示的腐熟度评价结果(98.5%)一致.基于多种光谱学指标的相关性分析,PⅤ,n/PⅢ,n与其它光谱学均呈现较好的相关性(r≥0.68),可以作为评价超高温堆肥腐熟度的光谱学指标.上述结果证实了超高温堆肥工艺可加快堆肥腐熟进程、缩短堆肥周期至20 d左右,在有机固废资源化领域具有极大的应用潜力.     

林可霉素菌渣堆肥微生物群落多样性分析

本试验以林可霉素菌渣-猪粪为原料、污泥-猪粪堆肥作对照,研究了林可霉素菌渣堆肥过程中残留林可霉素的降解情况,并基于Illumina Mi Seq高通量测序分析了林可霉素菌渣堆肥过程中微生物菌群的变化.结果表明:通过堆肥处理可以大幅度降解林可霉素菌渣中残留的林可霉素,经过33 d的堆肥处理后,林可霉素的残留量从最初的1 800 mg·kg-1降到483mg·kg-1,降解率高达73%.同时高通量测序结果表明,由于高含量的林可霉素残留,在堆肥初期和高温期林可霉素菌渣堆肥中细菌群落的分布丰度和多样性指数均低于污泥-猪粪堆肥,但真菌群落丰度和多样性均高于污泥-猪粪堆肥.林可霉素菌渣堆肥中细菌主要以Paucisalibacillus、Cerasibacillus、Bacillus、Virgibacillus、Ureibacillus、Paenibacillus、Sinibacillus属为主,而污泥-猪粪堆肥中主要以Truepera、Actinomadura、Pseudosphingobacterium、Pseudomonas、Luteimonas、Ureibacillus属为主,两者堆肥中微生物群落结构存在显著差异.随着堆肥进入腐熟期,林可霉素残留大幅度降解,抗生素对微生物的胁迫减小或解除,林可霉素菌渣-猪粪堆肥和污泥-猪粪堆肥相比,无论是细菌还是真菌,其微生物群落已逐渐趋同.表明堆肥处理可以大幅降解林可霉素残留,增加微生物多样性,有利于实现林可霉素菌渣无害化处理和资源化利用.     

长期储存亚硝化絮状污泥活性的恢复

为探究长期储存亚硝化絮状污泥的脱氮性能,采用CSTR反应器,接种4℃下储存了10个月的亚硝化絮状污泥,考察其活性恢复性能,并采用Mi Seq高通量测序技术分析了污泥中微生物菌群结构的变化情况.结果表明,控制DO为0.4~0.8mg·L~(-1)、pH值8左右、温度为(30±1)℃等条件,长期储存亚硝化絮状污泥的活性可以在15 d内迅速恢复,氨氮去除率和亚硝积累率均达到90%以上;此外,污泥颜色由接种初期的灰黑色迅速恢复至棕黄色,SVI值显著降低,MLVSS/MLSS升高,EPS含量明显增加.随着亚硝化性能的恢复,厌氧、发酵微生物被洗脱,Nitrosomonas等氨氧化细菌相对丰度显著增加,同时,Nitrospria等硝化菌的生长得到了有效抑制.经历长期储存的亚硝化絮状污泥可作为实现短程硝化快速启动的接种污泥,更有利于短程硝化工艺的实际应用.     

Investigation on mechanism of phosphate removal on carbonized sludge adsorbent

For the removal of phosphate (PO₄^3 -) from water, an adsorbent was prepared via carbonization of sewage sludge from a wastewater treatment plant: carbonized sludge adsorbent (CSA). The mechanism of phosphate removal was determined after studying the structure and chemical properties of the CSA and its influence on phosphate removal. The results demonstrate that phosphate adsorption by the CSA can be fitted with the pseudo second-order kinetics and Langmuir isotherm models, indicating that the adsorption is single molecular layer adsorption dominated by chemical reaction. The active sites binding phosphate on the surface are composed of mineral particles containing Si/Ca/Al/Fe. The mineral containing Ca, calcite, is the main factor responsible for phosphate removal. The phosphate removal mechanism is a complex process including crystallization via the interaction between Ca^2 + and PO₄^3 -; formation of precipitates of Ca^2 +, Al^3 +, and PO₄^3 -; and adsorption of PO₄^3 - on some recalcitrant oxides composed of Si/Al/Fe.     

Long-term observations of tropospheric NO2, SO2 and HCHO by MAX-DOAS in Yangtze River Delta area, China

Yangtze River Delta(YRD) area is one of the important economic zones in China. However,this area faces increasing environmental problems. In this study, we use ground-based multi-axis differential optical absorption spectroscopy(MAX-DOAS) network in Eastern China to retrieve variations of NO_2, SO_2, and formaldehyde(HCHO) in the YRD area. Three cities of YRD(Hefei, Nanjing, and Shanghai) were selected for long-term observations. This paper presents technical performance and characteristics of instruments, their distribution in YRD, and results of vertical column densities(VCDs) and profiles of NO_2, SO_2, and HCHO.Average diurnal variations of tropospheric NO_2 and SO_2 in different seasons over the three stations yielded minimum values at noon or in the early afternoon, whereas tropospheric HCHO reached the maximum during midday hours. Slight reduction of the pollutants in weekends occurred in all the three sites. In general trace gas concentrations gradually reduced from Shanghai to Hefei. Tropospheric VCDs of NO_2, SO_2, and HCHO were compared with those from Ozone Monitoring Instrument(OMI) satellite observations, resulting in R~2 of 0.606, 0.5432, and 0.5566, respectively. According to analysis of regional transports of pollutants, pollution process happened in YRD under the north wind with the pollution dissipating in the southeast wind. The feature is significant in exploring transport of tropospheric trace gas pollution in YRD, and provides basis for satellite and model validation.     

Alkali resistance promotion of Ce-doped vanadium-titanic-based NH3-SCR catalysts

The effect of K deactivation on V_2O_5/WO_3-TiO_2 and Ce-doped V_2O_5/WO_3-TiO_2 catalysts in the selective catalytic reduction(SCR) of NOxby NH_3 was studied.Ce-doped V_2O_5/WO_3-TiO_2 showed significantly higher resistance to K deactivation than V_2O_5/WO_3-TiO_2.Ce-doped V_2O_5/WO_3-TiO_2 with K/V = 4(molar ratio) showed 90% NOxconversion at 350°C,whereas in this case V_2O_5/WO_3-TiO_2 showed no activity.The fresh and K-poisoned V_2O_5/WO_3-TiO_2 and Ce-doped V_2O_5/WO_3-TiO_2 catalysts were investigated by means of in situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS),NH_3-temperature progress decomposition(NH_3-TPD),X-ray photoelectron spectroscopy(XPS) and H2-temperature program reduction(H_2-TPR).The effect of Ce doping on the improving resistance to K of V_2O_5/WO_3-TiO_2 were discussed.     

多级AO耦合流离生化工艺流量分配比优化及脱氮机制

为探究进水流量分配比对低温城市污水脱氮效率的影响,并解析多级AO耦合流离生化工艺脱氮规律,实验采用三级AO耦合流离生化工艺,在温度为(10±1)℃、水力停留时间8 h、气水比恒定的条件下处理模拟低C/N值城市污水.系统依次在进水比5∶4∶4(等容积负荷)、3∶2∶1(等停留时间)和25∶15∶6(等污泥负荷)这3种工况下运行.结果表明,该工艺对低温低C/N值污水的处理效果较好,其中在进水比为3∶2∶1的工况下脱氮效率最高,COD、NH+4-N和TN平均去除率分别为87. 44%、96. 63%和76. 81%.进一步对氮的迁移转化规律进行研究发现,制约工艺低温脱氮的主要因素为各级硝化效率,3∶2∶1的进水比合理地分配了进水负荷,各级硝化率均超过85%,为反硝化创造了有利条件,最终获得了较高的脱氮效率,此时系统也具有最高的总生物量.研究结果丰富了多级AO耦合工艺低温脱氮理论,同时为工程设计应用提供参考.     

污水生物处理中抗生素的去除机制及影响因素

环境中的抗生素污染日益严重,其诱导产生的抗生素抗性成为人类健康的重大威胁.通过对世界多地污水处理厂进、出水中抗生素浓度水平的文献调研汇总,发现当前的污水处理工艺不能实现抗生素的有效去除.吸附和生物降解是污水中抗生素的主要去除途径,因此本文深入地分析了吸附的作用机制和不同种类抗生素吸附程度的差异;从生物降解性能、降解菌和降解产物等方面分析抗生素在污水生物处理过程中的生物降解作用;分析讨论了水力停留时间、污泥停留时间、温度和工艺选型(传统活性污泥法、膜生物反应器和生物脱氮工艺)等污水生物处理工艺的运行条件对吸附和生物降解途径的影响,进而解析对抗生素去除效果的影响.菌群组成、生长基质供应情况和微污染物共存情况等因素对污水生物处理中抗生素迁移转化的影响需要更深入地研究.     

pH对污泥厌氧消化过程中抗生素降解迁移的影响

抗生素作为一种新型污染物,可随着城市污水厂中污泥的处理处置单元最终进入环境中,对人类健康造成潜在威胁.以城市污水厂的剩余污泥为研究对象,考察在不同初始p H(p H=5.5、6.5、7.5、8.5、9.5、10.5)条件下,12种抗生素在污泥厌氧消化过程中降解迁移的规律.结果显示,p H为7.5时,总抗生素去除率最高,为55.7%;p H为5.5时,总抗生素去除率最低,仅为21.7%.厌氧消化后,抗生素明显由固相向液相迁移,且总抗生素去除率与其固相迁移至液相的抗生素含量显著相关.