新疆油田采出水处理技术

近几年新疆油田研究成功对采出水的处理技术,根据油田采出水水质特点、水处理药剂的反应机理、水处理药剂与原水的混合机理、絮体长大的机理及絮体沉淀的机理,采用了稠油污水微涡旋处理技术,高效水质净化与稳定技术等,处理后的污水又用于回注,降低了运行成本,减少了环境污染。     

序批式生物膜法处理油田采油废水

采用序批式生物膜(SBBR)法处理油田采油废水。研究并开发了特殊活性污泥的培养和驯化方法。在被处理的污水中加入微生物促生剂FYS-5,可迅速培养出处理采油废水的微生物,用此种方法培养出的活性污泥的活性高,去除有毒有害物质的能力强,能够提高处理效率,保持良好的微生物生长状况。在SBBR装置进水COD容积负荷为0.5kg/(m3·d)及进水COD为500mg/L左右的条件下,经过近两个月的连续运转,COD平均去除率超过80%,出水中COD低于100mg/L,符合GB8978-1996《污水综合排放标准》的要求,经过处理的污水可以直接排放。     

页岩气增产采出水处理方法研究

针对页岩气增产采出水易起泡,难以平稳蒸发脱盐的问题,利用"预处理+多效蒸发"处理方法,对井站两种不同性质的采出水进行中试,连续监测各工艺单元处理后水质及蒸发出水水质。结果表明:通过破乳混凝、催化氧化、电荷中和及除硬等步骤,能够完全消除泡排水起泡性;中试稳定运行7d,两种泡排水蒸发出水水质稳定,COD浓度<55mg/L,NH4^+-N浓度<18mg/L,满足GB 8978-1996《污水综合排放标准》一级标准;Cl^-浓度<21mg/L,满足DB 51/190-1993《四川省水污染物排放标准》要求。     

采油废水厌氧处理系统的微生物群落特征

为了深入认识石油烃的厌氧降解过程,利用分子生物学技术分析了大庆油田采油废水处理系统厌氧池和进水中的微生物群落特征。基于DGGE和克隆文库的分析结果均表明,厌氧生物膜中存在的古菌源自于采油废水。厌氧生物膜和采油废水中的古菌主要是产甲烷菌,包括嗜甲基的Methanomethylovorans thermophila和利用氢和甲酸的Methanolinea tarda。值得注意的是,氢营养型的M.tarda在厌氧生物膜中得到了富集。进水和厌氧生物膜中的细菌群落结构明显不同。进水中的主要细菌类群为Epsilonproteobacteria,而生物膜中的主要类群为Nitrospira和Deltaproteobacteria。在厌氧生物膜中发现许多与产甲烷古菌(尤其是氢营养型产甲烷菌)协同降解石油烃类物质的细菌相关克隆:其中一个克隆与Syntrophus具有较高的同源性,该类菌是产甲烷菌介导的厌氧烃降解微生物区系中的关键细菌;许多Deltaproteobacteria克隆属于group TA类群,该类群细菌主要参与芳香族化合物产甲烷菌介导的厌氧降解过程。这些结果表明,在大庆油田采油废水厌氧处理系统中已经建立起由产甲烷菌所介导的厌氧石油烃降解的微生物区系。     

Chemical fate,latitudinal distribution and long-range transport of cyclic volatile methylsiloxanes in the global environment: A modeling assessment

Cyclic volatile methylsiloxanes (cVMS) such as octamethycyclotetrasiloxane (D4), decamethycyclopentasiloxane (D5), and dodecamethylcyclohexasiloxane (D6) are widely used as intermediates in the synthesis of high-molecular weight silicone polymers or as ingredients in the formulation of personal care products. The global environmental fate, latitudinal distribution, and long range transport of those cVMS were analyzed by two multimedia chemical fate models using the best available physicochemical properties as inputs and known persistent organic pollutants (POPs) and highly persistent volatile organic chemicals (“fliers”) as reference. The global transport and accumulation characteristics of cVMS differ from those of typical POPs in three significant ways. First, a large fraction of the released cVMS tends to become airborne and is removed from the global environment by degradation in air, whereas known POPs have a tendency to be distributed and persistent in all media. Secondly, although cVMS can travel a substantial distance in the atmosphere, they have little potential for deposition to surface media in remote regions. This contrasts with a deposition potential of known POPs that exceeds that of cVMS by 4–5 orders of magnitude. Thirdly, cVMS have short global residence times with the majority of the global mass removed within 3 months of the end of release. Global residence times of POPs on the other hand are in years. The persistent fliers resemble the cVMS with respect to the first two attributes, but their global residence times are more like those of the POPs.     

Assessment of decadal changes in sediment contamination in a large connecting channel (Detroit River,North America)

Concentrations of selected heavy metals (Cd, Cu, Hg, Pb, Zn) and organic contaminants (PCBs, PAHs) were investigated in samples from the Detroit River (Great Lakes, North America) in 1999 and 2008/09 collected using a stratified random sampling design. Getis–Ord geospatial analysis was used to further establish locations of areas demonstrating significantly high and low contaminant concentrations in the river. Based on the stratified random sampling design, a majority of the examined metals and organic contaminants demonstrated little or no trends with respect to regional sediment concentrations and river-wide mass balances over the investigated time interval. The Getis–Ord analysis revealed local scales of contaminated and clean areas which did not conform to the original strata used in the geostatistical sampling design. It is suggested that geospatial analyses such as Getis–Ord be used in the design of future sediment quality surveys to refine locations of strata that can simultaneously address sediment recovery over system-wide, regional and local spatial scales.     

Determination of PCDDs,PCDFs, PCBs and HCB emissions from the metallurgical sector in Poland

Background The aim of the project was to measure the actual emissions of PCDD/F, PCBs and HCB from 20 selected metallurgical installations in Poland, in order to update the national inventory of dioxin emission from metallurgical industry for developing a strategy for dioxins and furans emission abatement from the subject facilities (UNEP 2005). Methods Sampling methodology used in this work was developed at the Cracow University of Technology because of the complexity of simultaneous sampling and determining PCDFs, PCDDs, PCB and HCB. For the determination a GC-MS/MS system was used. Results and Discussion Results from the work indicate that the highest dioxins and PCB concentrations were recorded for iron ore sintering plants at 1.10–1.32 ng total¹ TEQ/Nm³ followed by aluminium scrap melting at 0.03–0.66 ng total TEQ/Nm³. The highest HCB concentrations at 613–1491 ng/Nm³ were also recorded for iron ore sintering plants, whereas at aluminium plants the HCB concentrations were in the range of only 10.1–22.7 ng/Nm³. Conclusions The above investigations indicate that secondary aluminium production is the most significant dioxins source, if calculated as emission factor values. However, iron ore sintering plants are operating at much higher production capacity, causing this process to become the major source of dioxins, PCB and HCB pollution to the atmosphere in Poland. Recommendations and Perspectives Based on the performed tests and the environmental reviews of selected plants several recommendations were formulated for the reduction of generation or of emission of these pollutants from iron ore sintering plants, electric arc furnace steel production processes, hot-blast furnace operations, secondary aluminium smelting and primary zinc production from zinc cathodes.     

离子色谱法测定油田采出水中总氮和总磷

油田采出水经光电催化氧化法处理后,有机物和油被充分降解,用离子色谱法测定 NO3-、PO3-4,5次测定结果的 RSD为3．1％～5．8％。该方法测定出水中 NO3-、PO3-4质量浓度可代表除油处理后原水中总氮、总磷质量浓度,与分光光度法测定原水中总磷、总氮的结果相比,重现性好、耗时少。     

QSPR for prediction of subcooled vapor pressures (log PL) of polychlorinated trans-azobenzenes

In this study the values of subcooled vapor pressures (log P_L) were estimated for 209 trans chloroazobenzenes (Ct-ABs) that fill some gaps in analytical and experimental data on these compounds. There are 209 chloro derivatives of trans azobenzenes that are relatively stable and more environmentally relevant than 209 chloro cis congeners. The calculations models were based on the Quantitative Structure-Property Relationship (QSPR) scheme using the semi-empirical method (PM6) in molecular package (MOPAC) software and density functional theory (DFT) method using B3LYP functional and 6-311++G** basis set) in Gaussian 03 software method and the artificial neural networks (ANNs) prediction. The values of log P_L predicted by models used varied between ?3.94 to ?2.66 for Mono-; ?4.85 to ?2.97 for Di-; ?5.18 to ?3.17 for Tri-; ?6.02 to ?3.77 for Tetra-; ?6.64 to ?4.64 for Penta-; ?7.36 to ?4.76 for Hexa-; ?7.54 to ?5.79 for Hepta-; ?7.75 to ?6.64 for Octa-; ?7.89 to ?7.44 for Nona-Ct-Abs; and ?8.09 and ?8.13 for Deca-Ct-AB. Based on these values Ct-ABs can be grouped localized among relatively low (log P_L ?4 to ?2) and low (log P_L < ?4) mobile Persistent Organic Pollutants (POPs). Both the calculation methods employed were characterized by similar prediction ability of subcooled vapor pressure values of Ct-ABs, while those of PM6 are much more efficient due to a cheaper hardware used and around 300-fold less time spent on calculations.     

气氛含氧量对DDT热处理特性的影响

滴滴涕属于有机氯农药,其所含成分DDTs在环境中难以降解,并具有生物毒性。利用高温管式炉研究气氛中含氧量对滴滴涕热处理特性的影响,为研发废弃滴滴涕高温热处理技术提供理论依据。实验结果表明,在600℃时,滴滴涕去除率最高为含氧量21%时的70.48%;在900℃条件下,当含氧量为21%时DDT去除率≥99%;在1 200℃条件下,当含氧量≥12%时DDT去除率≥99.9%。在滴滴涕热处理残渣中,o,p’-DDT占DDTs总量的比例在3个温度段中都随含氧量的增加而增长,DDT则都随含氧量增加而减少,且上述变化随温度升高而幅度加大。在尾气中,p,p’-DDE占DDTs总量的比例在3个温度段中都随含氧量增加而递增,在1 200℃条件下尤为明显。