糖蜜酒精厂环境保护验收清洁生产评价研究

糖蜜是糖厂榨糖后的副产品,含有可发酵性的糖45％∽52％,是直接用于发酵生产酒精的较好的原料.文章以广西某糖蜜酒精厂为例,在调查了解酒精厂生产工艺与装备、资源能源利用指标、污染物产生指标、废物回收利用率和环境管理要求等五个方面的基础上,认真细致分析环境保护竣工验收监测数据及生产报表数据,按照（HJ 581-2010）《清洁生产标准酒精制造业》（国家环境保护部）的要求对酒精厂清洁生产水平进行评价,并根据评价结果提出进一步提高清洁生产水平的建议和要求.     

生活污水处理厂污泥处置技术研究

针对生活污水处理厂污泥处置技术,介绍了国内外污泥的处理现状,提出了传统的污泥处置技术,主要是海洋倾倒,污泥消化技术法,污泥堆肥技术法,污泥的土地利用和污泥的有效利用法,给出林地利用与绿化利用随着污泥量的增长,污泥的处置越来越来受到人们的关注。介绍了国内外污泥处理现状和传统污泥处理处置方法,分析了污泥稳定和资源化处置技术及应用进展,提出了污泥堆肥和堆肥后污泥的土地利用是符合中国国情的污泥处置与资源化利用途径。     

三峡水库消落带土壤与优势植物淹水后对土-水系统汞形态的影响

三峡库区消落带落干期植被生长茂盛,蓄水后消落带被淹没,土壤-植物系统在长时间淹水情况下,随着体系内物理化学性质的改变,汞形态也会发生变化,从而对库区水生生态系统中汞含量以及形态带来一定的影响.为此,本研究选取三峡库区4种优势植物室内栽培,再进行室内模拟淹水试验,研究淹水后土壤、水体中甲基汞(Me Hg)以及其他形态汞的变化.结果表明,淹水过程中植物的存在有利于土壤Me Hg的生成,同时对上覆水不同形态汞浓度影响显著.狗牙根作为消落带优势种,由于其体内总汞及甲基汞含量较高,淹水后对土壤以及上覆水系统中甲基汞以及其他汞形态的影响最为明显.淹水第90 d,狗牙根+土+江水(B1)处理土壤Me Hg的含量最高,为(1 135.86±113.84)ng·kg~(-1),是不加植物的对照处理土+江水(CK2)中土壤Me Hg含量的2倍左右;上覆水总甲基汞(TMe Hg)、溶解态甲基汞(DMe Hg)、总汞(THg)、溶解态汞(DHg)和活性汞(RHg)均呈峰值偏左的抛物线状变化,在第30 d时达到峰值,其中B1处理上覆水TMe Hg、THg和DHg最高,分别为(2.88±0.06)、(40.29±2.42)和(35.51±3.77)ng·L~(-1),三者中溶解态汞是其主要存在形式.因此可以推测三峡库区消落带植物淹水后将增加水库汞污染负荷.     

火电厂烟气排放对广州大气环境的影响

广州市是酸雨、可吸入颗粒物污染严重的地区之一,这与其能源结构以煤为主有关.广州发电厂以燃煤为主,其周围大气采样数据分析显示燃煤电厂可对周围大气环境造成较大影响,是酸雨前体物、可吸入颗粒物的主要排放源.酸雨破坏了生态环境,也阻碍了经济的发展;燃煤排放的烟尘细颗粒物属于可吸入颗粒物,其上附着的As、Cr等微量元素多为致癌物质和致基因毒性诱变物质,对周围居民的健康危害极大.最后, 对当前的环境保护工作及存在的问题进行了阐述.     

矿化垃圾混配种植介质的盆栽实验研究

矿化垃圾营养成分和有机质含量较高,但含有重金属和盐分.为了解矿化垃圾的施加比例对植物的生长影响以及植物对矿化垃圾混配种植介质中营养成分的吸收和重金属的富集,将矿化垃圾和本地绿化土按照不同比例混配,研究混配种植介质的理化性质的改善条件、矿化垃圾对植物体内的生物量和叶绿素含量的影响、植物对混配种植介质中营养成分的吸收量以及植物体内各种重金属累积浓度,探索矿化垃圾的最佳施用比例.实验结果表明,矿化垃圾可改善上海本地土壤贫瘠的普遍状况,其添加质量分数在50%～75%合适,对植物生长有利.     

添加不同钝化剂降低污泥堆肥的植物毒性研究

高温堆肥后污泥的土地利用可充分发挥资源化、无害化的优势,污泥土地利用防止重金属污染一直是污泥施用中最重要的问题。通过测验发芽率指数这一代表植物毒性的指标证明,通过在污泥堆肥中加入粉煤灰、磷矿粉和草炭等不同的改性剂或重金属钝化剂可大大降低堆肥的植物毒性,从而降低污泥中重金属的可利用性。     

湖州市埭溪镇污水处理厂的工程设计

湖州市埭溪镇污水处理厂的设计规模,近期为2万m^2／d,远期为3万m^2／d,其污水处理工艺采用改良式A^2／O工艺,污泥处理工艺采用带式浓缩脱水一体机。文中着重介绍了工程设计参数、处理工艺流程及其设计特点。     

The Influence of a Coal-Fired Power Plant in Turkey on the Chemical Composition of Rain Water in a Certain Region

In this study, the chemical composition of the rainwater in Yatağan, which is a region surrounding a coal power plant was investigated from February to April 2002. Rainwater samples were obtained from Yatağan, located northwest of Muğla City in Turkey. pH values and concentrations of major ions (Ca²⁺, Na⁺, K⁺, , , ) in the rainwater samples were analyzed. The pH varied from 5.1 to 7.9 with an average of 6.7 which was in alkaline range considering 5.6 as the neutral pH of cloud water in equilibrium with atmospheric CO₂. In the total of 30 rain events, only three events were observed with water in the acidic range (<5.6), which occurred after continuous rains. The equivalent concentration of components followed the order: Ca²⁺ > > Na⁺ > > > K⁺ > H⁺. The anion and cation concentrations in the rainwater samples showed a high sulphate concentration (131 μEq/l), as well as high sodium (40 μEq/l) and calcium (298 μEq/l) concentrations. These values indicate that one probable source of the high sodium concentration is fly ash, after the coal burning process and the power plant can be effective on level concentrations in rainwater. In addition, the dust-rich local and surrounding limestone environment might have caused the high concentration of Ca²⁺ in rainwater of the Yatağan Basin. Due to a large contribution of these cations to the sulphate neutralization action, the rainwater of this region displays only a moderate acidity, which does not cause significant environmental impact.     

Impact of Bioaugmentation with a Consortium of Bacteria on the Remediation of Wastewater-Containing Hydrocarbons (5 pp)

Goals, Scope and Background It has been observed that hydrocarbon treated wastewaters still contain high COD and a number of intermediates. This suggests that the required catabolic gene pool for further degradation might be absent in the system or, that its titer value is not significant enough. By providing the desired catabolic potential, the overall efficiency of the treatment system can be improved. This study aims to demonstrate this concept by bioaugmentation of a lab-scale reactor treating refinery wastewater with a consortium having the capacity to complement the alkB genotype to the available microbial population. Methods Two reactors were set up using activated biomass collected from a refinery treatment plant and operated at a continuous mode for a period of 8 weeks. The feed to both reactors was kept constant. Crude oil was spiked regularly. One reactor was bioaugmented with a consortium previously described for crude oil spill remediation. The efficiency of the bioaugmented reactor was demonstrated by reduced COD. The changes in the microbial population over a period of time were analyzed by RAPD. Catabolic activity of the biomass in both reactors was monitored by PCR. The presence of the catabolic loci was confirmed by Southern Hybridization. Results and Discussion 52.2% removal of COD was observed in the bioaugmented reactor while only 15.1% reduction of COD was observed in the reactor without bioaugmentation. The change in microbial population can be seen from the 4th week, which also corresponds to improved catabolic activity. The presence of the bedA locus was seen in all samples, which indicates the presence of aromatic degraders, but the appearance of the alkB locus, from the 6th week onwards, which was observed only in the samples from the bioaugmented reactor. The results suggest that the gene pool of the bioaugmented reactor has catabolic loci that can degrade accumulated intermediates, thus improving the efficiency of the system. Conclusions In this study, improvement of efficiency of bioremediation was demonstrated by addition of catabolic loci that are responsible for degradation. Bioaugmentation was carried out in biomass that was collected from an ETP (effluent treatment plant) treating hydrocarbon containing wastewater to study the strategies for improvement of the treatment system. Biostimulation, only marginally improved the efficiency, when compared to bioaugmentation. The improved efficiency was demonstrated by COD removal. The presence of the alkB locus suggests the importance of a catabolic gene pool that acts on accumulated intermediates. It is well documented that straight chain aliphatics and intermediates of aromatic compounds after ring cleavage, accumulate in refinery wastewater systems, thereby hindering further degradation of the wastewater. Supplementation of a catabolic gene pool that treats the lower pathway compounds and alkanes will improve the overall efficiency. In this study, results suggest that the alkB locus can also be used to monitor the degradative mode of the activated biomass. Recommendations and Perspective . Pollution from petroleum and petroleum products around the globe are known to have grave consequences on the environment. Bioremediation, using activated sludge, is one option for the treatment of such wastes. Effluent treatment plants are usually unable to completely degrade the wastewater being treated in the biological unit (the aerator chambers). The efficiency of degradation can be improved by biostimulation and bioaugmentation. This study demonstrates the improved efficiency of a treatment system for wastewater containing hydrocarbons by bioaugmentation of a consortium that supports degradation. Further experiments on a pilot scale are recommended to assess the use of bioaugmentation on a large scale. The use of molecular tools, like DNA probes for alkB, to monitor the system also needs to be explored.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.