联合生物法处理炼油厂含油污泥的研究

大港石化公司采用联合生物法处理含油污泥,对使用好氧、厌氧工艺处理含油污泥的结果进行了探讨。实验结果表明:先进行好氧处理然后脱水再进行厌氧堆肥工艺处理含油污泥,除油率达到97.6%,除磷、钾的指标低于《城镇垃圾农用控制标准》(GB8172-87)的要求外,其他指标均符合该标准要求,且避免了二次污染。     

尾气循环技术在国内顺酐装置的应用

顺酐生产过程排放的废气中含有大量未反应原料、副产物CO和挥发性有机物(VOC)等,对其进行处理使之达标排放,回收其中可利用的物质或能量有重要意义。吐哈石化厂顺酐装置采用CONSER公司工艺技术,新增部分尾气回收生产工艺路线,回收40%的尾气中的正丁烷,实现了蒸汽分阶利用,排放的废气中SO2、NOx、颗粒物等达到GB16297-1996《大气污染物综合排放标准》中二级标准。     

内循环三相生物流化床处理生活污水的试验研究

对内循环三相生物流化床处理生活污水进行了试验研究,探讨了生物膜的形成和水力停留时间及曝气量对处理效果的影响。结果表明：在HRT为6h,曝气量为0.6m3/h,进水COD和NH4＋-N分别为240.2~298.7mg/L和29.1~68.9mg/L条件下,平均COD去除率为83%,NH4＋-N去除率为95.1%。     

NaCl和KCl对厌氧污泥抑制的动力学研究

在厌氧颗粒污泥和厌氧絮状污泥系统中,进行盐质量浓度(NaCl或KCl质量浓度,下同)对厌氧污泥抑制动力学的研究,得到不同拟合的COD降解动力学方程及参数.实验结果表明:当盐质量浓度为10～30 g/L时,KCl对厌氧污泥的COD比降解速率的抑制程度大于NaCl;当盐质量浓度由0 g/L增至10 g/L时,半速率常数逐渐增加;当盐质量浓度由10 g/L增至30 g/L时,半速率常数逐渐减小;在厌氧污泥系统中,NaCl抑制作用下的盐抑制常数高于KCl,且颗粒污泥的盐抑制常数高于絮状污泥.     

UASB反应器处理染料及印染废水的研究进展

综述了国内外UASB反应器处理染料及印染废水的研究概况.分析了UASB反应器处理废水存在的问题,并给出了相应的建议.展望了UASB反应器处理染料及印染废水的发展趋势,指出厌氧UASB-好氧法组合工艺是目前处理染料及印染废水的一种经济而有效的方法.     

The Effect of Masterbatch Addition on the Mechanical, Thermal, Optical and Surface Properties of Poly(lactic acid)

There has been considerable interest in the use of the biodegradable polymer poly(lactic acid) (PLA) as a replacement for petroleum derived polymers due to ease of processability and its high mechanical strength. Other material properties have however limited its wider application. These include its brittle properties, low impact strength and yellow tint. In an attempt to overcome these drawbacks, PLA was blended with four commercially available additives, commonly known as masterbatches. The effect of the addition of 1.5 wt% of the four masterbatches on the mechanical, thermal, optical and surface properties of the polymer was evaluated. All four masterbatches had a slight negative effect on the tensile strength of PLA (3–5% reduction). There was a four fold increase in impact resistance however with the addition of one of the masterbatches. Differential scanning calorimetry demonstrated that this increase corresponded to a decrease in the polymer crystallinity. However there was an associated increase in polymer haze with the addition of this masterbatch. The clarity of PLA was improved through the addition of an optical brightener masterbatch, but the impact resistance remained low. The glass transition and melting temperatures of PLA were not affected by the addition of the masterbatches, and no change was observed in surface energy. Some delay in PLA degradation, in a PBS degradation medium at 50 °C, was observed due to blending with these masterbatches.     

Experimental study of recycling lightweight concrete with aggregates containing expanded glass

The focus is on the issue of waste management when constructing and recycling lightweight concrete (LWC) with aggregates containing expanded glass. The paper analyses the recycling of concrete from lightweight aggregates, and on the important issue of environmental and waste management. The characteristics of recycling LWC such as density, compressive strength and thermal conductivity are investigated, and compared with normal existing concrete from lightweight aggregates. The results indicate that it is possible to recycle lightweight concrete construction waste. The described method shows great possibilities for increasing the use of construction waste materials from LWC containing expanded glass, in order to benefit from better use of the available capacity from existing construction waste. The characteristics of density, compressive strength and thermal conductivity from the new recycled material were compared with normal existing concrete from lightweight aggregates, such as changes in dependency on the type and parts of waste as well as its new binding components. Thus, a new recycled material has been created with new characteristics of density, compressive strength and thermal conductivity, which is conform to the compressive strength class and rules on heat protection and energy efficiency use in buildings (SI OJ RS No. 42/2002). Laboratory density, compressive strength, and thermal conductivity tests results showed that LWC can be produced by the use of waste LWC with aggregates containing expanded glass. However, the use of waste LWC with aggregates containing expanded glass seems to be necessary for the production of cheaper and environmentally friendly LWC.     

拒绝服务攻击/分布式拒绝服务攻击防范技术的研究

研究常见的拒绝服务攻击和分布式拒绝服务攻击方法,深入分析各种相关防护技术,提出了从设备自身加固入手,以分布式检查,管理和技术双管齐下的思路。给出了应对这种目前开放网络中的顽疾的综合解决方案。笔者提及的相关解决方案涉及到安全评估加固技术、攻击检测技术、流量清洗技术、安全管理技术;也给出了各种不同职责岗位的工作职责,提出了防止拒绝服务攻击必须从做好安全加固,采用积极的方式应对这种攻击的思路。笔者提出的观点可用于指导企业进行综合的拒绝服务攻击防御,也可以作为安全技术及理论的研究者的参考,提到的各种防范技术均经过了实践的验证。     

企业安全管理中的潜流文化现象与应对方略

简介潜流安全文化的内涵,阐述潜流安全文化的隐蔽性、离散性、传承性和不稳定性的特点,剖析潜流安全文化形成的根源,提出应对潜流安全文化的扬长避短、因势利导、强化沟通、扩大参与、落实承诺和深化激励的方略。通过对企业安全管理中的潜流文化现象与应对方略的分析,得出以下结论:企业潜流安全文化是客观存在的,同时企业管理者是可以对企业潜流安全文化进行有效管理的;认识和管理企业安全管理中的潜流文化现象,可以有力推动企业安全文化建设工作的顺利开展。     

可靠性理论在公共安全领域的应用研究

对公共安全体系从系统可靠性的视角,综合运用可靠性方面的知识,构建公共安全系统混联模型;进而将可靠性分配理论与故障树分析方法相结合,根据系统安全目标的要求,确定混联系统的第一层次各单元事件的可靠性目标值,对构成各单元的各个下属单元采取最小工作量可靠度分配方法,从而建立系统中各单元可靠度再分配量化模型。通过建筑物火灾引起人员伤亡事故实例,详述系统各单元可靠性分配的计算过程。研究表明,可靠性理论可以成功地应用到公共安全领域;使系统在给定的目标值条件下达到系统的安全性优化,实现了公共安全保障效能,减小灾害损失。