经济型阳离子淀粉絮凝剂的制备及其对印染废水的处理效果

采用玉米淀粉为原料、氯化缩水甘油三甲基铵（GTA）作阳离子化试剂、水-乙醇混合液作分散剂、NaOH作碱催化剂,制备了经济型阳离子淀粉絮凝剂（简称经济型阳离子淀粉）。实验结果表明：在淀粉加入量110g、GTA加入量30g、NaOH加入量1．6g、分散剂中m（水）：m（乙醇）=1：1、m（分散剂）：m（淀粉）=0．50：1、反应温度80℃、反应时间2．5h的条件下,可制得取代度（DS）为0．31的经济型阳离子淀粉;用该经济型阳离子淀粉与聚丙烯酰胺（PAM）联用处理印染废水,当经济型阳离子淀粉加入量为140mg／L、PAM加入量为4mg/L、废水pH为8时,印染废水的色度去除率和COD去除率分别达92％和82％。该方法絮凝效果好,药剂费用低,产生的污泥少。     

阳离子型聚合物对低温低浊水的絮凝效果与形态学特性

采用微絮凝-深床直接过滤工艺,以西安市曲江水厂低温低浊水质为原水(水温低于10 ℃,初始浊度低于10NTU),投加阳离子型聚合物(简称CP)作主混凝剂或助凝剂,借助分形数学理论与图像分析技术,对滤料粒径、原水浊度、原水温度、药剂种类、聚合物分子量及投加量、混合强度等因素对处理效果的影响进行了研究,分析探讨了不同药剂处理低温低浊水的作用机理、絮凝形态学特征以及絮体结构的分形特性.结果表明,①当温度低于4 ℃、初始浊度小于4NTU时,不宜单独采用Al2(SO4)3或PAC作为絮凝剂;当温度为4～10 ℃、初始浊度小于10NTU时,如果只投加Al2(SO4)3或PAC作为絮凝剂,宜用细砂滤料过滤;低温低浊条件下,无机混凝剂形成的絮体粒径小、结构松散脆弱、有效质量密度低、沉速慢,但表征絮体分形特性的分维值较高.②CP作絮凝剂能显著改善低温低浊水的絮凝效果与过滤性能,但混合强度需增大,宜用粗砂滤料过滤;③单独用CP作絮凝剂时,宜投加分子量较低的弱阳性聚合物或投加低剂量较高分子量的强阳性聚合物;CP用作助凝剂时,能显著减少主混凝剂用量,但宜投加强阳性聚合物或增加弱阳性聚合物的剂量.④CP兼备电性中和与吸附架桥絮凝作用,能形成粒径较大、吸附性能与过滤性能良好的网状絮体构型,其有效质量密度高,产生的污泥量少,污泥沉降速度快,脱水效果好,但分维值低.⑤各种水处理药剂的处理效果为:Al2(SO4)3(或PAC) CP＞CP＞PAC＞Al2(SO4)3,这种差别由絮体的形态学特性与构型特征各异引起.     

胶束强化超滤去除水中双酚A

采用截留分子量(MWCO)为5000 Dalton、1000 Dalton的聚砜超滤膜,MWCO为1 kDa的再生纤维素超滤膜;采用十二烷基苯磺酸钠(SDBS)、曲拉通100(TritonX-100)、吐温80(Tween-80)、烷基多苷(APG)为表面活性剂,用胶团强化超滤工艺去除水中双酚A。研究了不同材质和截留分子量的超滤膜、表面活性剂浓度、膜操作压力、溶液pH和溶液中电解质等因素对该工艺的影响。结果表明,SDBS对双酚A有较好的去除效果,去除率在80%以上。在H+和Na+存在的条件下,双酚A的截留率增加,透过液中SDBS浓度降低。SDBS与非离子表面活性剂的复配可以提高双酚A截留率,降低透过液中SDBS的浓度,复配效果优劣顺序为Tween-80TritonX-100APG。     

表面活性剂改性4A分子筛对Cr(VI)的吸附行为

采用浸渍法对4A分子筛进行表面改性,通过引入阳离子表面活性剂,使4A分子筛表面附着季铵型阳离子,并与反离子Br-形成"阴离子交换膜",从而促使更多的Cr(VI)阴离子通过离子交换吸附到改性4A分子筛上,通过X-射线衍射(XRD)和傅里叶变换红外光谱(FTIR)对样品的物相结构和组成进行表征分析。研究表明,表面活性剂的类型和疏水碳氢链结构会影响4A分子筛的吸附能力,十八烷基三甲基溴化铵(OTAB)碳氢链长,在分子筛表面形成的双分子层密,对Cr(VI)的吸附量最大。采用准一级、准二级、Elovich和Bangham动力学模型对六价铬的吸附数据进行拟合,其中准一级动力学方程最符合十八烷基三甲基溴化铵改性分子筛的吸附行为。同时,分别从Langmuir和Redlich-Peterson等温吸附模型获得六价铬的最大吸附量为13.98 mg/g,且改性分子筛以均一表面吸附为主。     

Ecotoxicity and biodegradability of antielectrostatic dicephalic cationic surfactants

Four series of dicephalic cationic surfactants, considered as new antielectrostatic agents have been investigated in order to establish their toxicity and biodegradability. Among them N,N-bis[3,3′-(dimethylamine)propyl]alkylamides, N,N-bis[3,3′-(dimethylamine)propyl]alkylamide dihydrochlorides, N,N-bis[3,3′-(trimethylammonio)propyl]alkylamide dibromides and N,N-bis[3,3′-(trimethylammonio)propyl]alkylamide dimethylsulphates with different hydrophobic chain length (n-C₉H₁₉ to n-C₁₅H₃₁) and type of counterion (chloride, bromide and methylsulfate) have been studied. The inhibitory effect against microorganisms has been examined using model gram-positive and gram-negative bacteria, and yeasts. None of the tested surfactants have shown antimicrobial activity against gram-negative bacteria (Escherichia coli, Pseudomonas putida) and yeasts (Saccharomyces cerevisiae, Rhodotorula glutinis) at a concentration below 1000 μg mL⁻¹, however some of them were moderately active against gram-positive bacteria (Staphylococcus aureus, Bacillus subtilis). The Microtox® test was successfully applied to measure EC₅₀ values of the studied dicephalic cationic surfactants. Their toxicity to Vibrio fischeri depended upon the alkanoyl chain length with the EC₅₀ values in a range of 2.6-980 mg L⁻¹. N,N-bis[3,3′-(dimethylamine)propyl]alkylamide dihydrochlorides 2a-b and N,N-bis[3,3′-(trimethylammonio)propyl]alkylamide dibromides 3a-b comprising n-decanoyl and n-dodecanoyl hydrophobic tails appeared to be the least toxic. Furthermore, the biodegradability under aerobic conditions of 2a-b, 3a-b was evaluated using OECD Method 301F. According to the obtained results 2a, 3a-3b can be considered as almost readily biodegradable and they are not expected to be persistent in the environment. Additionally, partial biodegradation was observed for 2b, indicating its possible biodegradation in wastewater treatment systems.     

阳离子表面活性剂十六烷基三甲基溴化铵对酞酸酯类化合物增溶性研究

用阳离子表面活性剂十六烷基三甲基溴化铵对六种酞酸酯类化合物(五种脂肪链酞酸酯和一种苯基酞酸酯)进行了增溶性实验．结果表明,在表观浓度(Ｃｓ)小于临界胶速浓度(ＣＭＣ)时,十六烷基三甲基溴化铵对四种酞酸酯(ＤＭＰ和ＤＰｈＰ除外)有一定程度的增溶作用;当Ｃｓ大于ＣＭＣ时,对六种化合物的增溶性显著增强．其增溶性(Ｓｔ/Ｓｗ)随Ｃｓ增大而线性递增:当Ｃｓ＜ＣＭＣ时,Ｓｔ/Ｓｗ＝ａ＋Ｋｍｎ·Ｃｓ,ｒ＞０．９０,ｎ＝５;当Ｃｓ＞ＣＭＣ时,Ｓｔ/Ｓｗ＝ａ＋Ｋｍｃ·Ｃｓ,ｒ＞０．９９,ｎ＝５． 各化合物增溶系数随各自固有水溶性(Ｓｗ)减小而增大(苯基酞酸酯有所反常),ｌｇＫｍｎ和ｌｇＫｍｃ与各自ｌｇｌ/Ｓｗ具有良好的线性正相关性．本文进一步对增溶机理进行了分析解释．     

紫外分光光度法在水中阴离子表面活性剂标准样品研制中的应用

研究了阴离子表面活性剂水溶液的紫外吸收特性,并将研究结果用于阴离子表面活性剂水质标样的稳定性,均匀性和定值工作,简化了操作手续,获得了准确的分析结果。     

Novel Polymeric Materials from Biological Oils

A variety of novel polymeric materials ranging from elastomers to tough, rigid plastics have been prepared by the cationic copolymerization of regular soybean oil, low-saturation soybean oil, or conjugated low-saturation soybean oil with various alkene commonomers. Using appropriate compositions and reaction conditions, 70–100% of the soybean oil is covalently incorporated into the cross-linked polymer networks, contributing significantly to cross-linking during copolymerization. The resulting thermosets exhibit thermophysical and mechanical properties that are competitive with those of their petroleum-based counterparts. In addition, good damping and shape memory properties have been obtained by controlling the degree of cross-linking and the rigidity of the polymer backbone. New materials with similar characteristics have also been produced from other biological oils, including tung, and fish oils using the same technique. The new, more valuable properties of these bioplastics suggest numerous promising applications of these novel polymeric materials.     

有机阳离子型电荷杀菌材料研究现状及展望

细菌等致病微生物可通过空气、水、土壤、食物等途径在自然界中传播,易对人体造成诸如肺结核、淋病、鼠疫等健康风险。目前广泛使用的灭菌方式包括紫外线、臭氧、氯气、电荷等物理或化学方法,其中电荷杀菌因具有无组织毒性的优点被广泛使用。研究表明：有机阳离子型电荷杀菌材料相比传统的金属离子杀菌材料具有抗菌效能优异、不产生耐药性、生物安全性高等优点,其杀菌性能受分子大小、烷基链、反离子类型、电荷密度等因素影响。本文系统综述了目前有机阳离子型电荷杀菌材料的类型、结构特征、杀菌性能及影响因素,抗菌机理及应用现状,分析了其存在的问题和发展方向,为有机阳离子型电荷杀菌材料的后续研究和应用提供一定的借鉴和指导。     

PM2.5中类腐殖质表面活性测定方法与实例分析

建立了大气细粒子中类腐殖质（HULIS）表面活性的动态表征方法,并以华北平原乡村站点冬季大气PM_2.5样品为例,对PM_2.5中HULIS的表面活性进行表征.HULIS碳质组分（HULIS-C）浓度为2.0~4.6μg C/m³,占水溶性有机碳和总有机碳的比例分别为31%~40%和20%~26%.浓度为88~200mg C/L的HULIS水溶液,其表面张力相对于纯水降低了18%~22%.HULIS-C浓度在低于70mg C/L时表面张力降低显著,在88~320mg C/L之间降低相对缓慢.动态表面张力随着时间变化逐渐降低,在液滴形成后200s以内表面张力下降迅速,之后趋于平缓,说明表面活性分子在液滴中扩散趋于稳定需要一定的时间,该特征时间可能影响表面活性物质在云凝结核活化时的作用.证实了在污染地区的大气PM_2.5中含有一定量的表面活性物质,这些物质可能对颗粒物活化为云滴、雾滴过程产生显著影响;表面活性物质的存在可能在外界湿度变化过程中导致颗粒物发生液-液相分离现象,在颗粒物表面形成有机膜,影响活性分子摄取以及半挥发性物质的气-粒分配过程,从而影响大气非均相反应过程.