外绝缘用液体硅橡胶老化现象的微观表征

本文针对近年来出现在一些变电站SF6电压、电流互感器的液体硅橡胶绝缘护套出现龟裂老化这一现象,对发生老化的硅橡胶材料进行了性能测试和试验,并利用红外光谱分析、XPS分析、热失重等手段分析了其微观结构和物质组成的变化。研究发现老化后的液体硅橡胶中Si-C、Si-O官能团和Si、C、O元素的相对含量发生了变化,且随着老化程度的增加呈现出较为明显的规律,老化越严重,Si-C键含量越少,C元素的含量越少,O元素含量越多。本文认为,用官能团含量、元素相对含量可以准确地表征液体硅橡胶材料的老化程度。通过对不同老化程度的液体硅橡胶进行的憎水性、耐漏电起痕性能的试验也证实了本文的观点。     

Metal associations in anoxic sediments and changes following upland disposal†

The ecological effects of heavy metals in contaminated sediments are more determined by the chemical form and reactivity than by the level of accumulation. Dredging of anoxic sediments and disposal on land is attended by changes of redox conditions. Under oxidizing conditions some controlling solid compounds may change gradually thus changing the solubility of certain metals.

Chemical extraction experiments for estimating characteristic association forms of heavy metals in anoxic sediments were carried out, both under presence and absence of air during the analytical procedure. Drying of the sediment decreases the proportion of the sulfidic metal fractions to a stronger degree, and oxidized Cd and Zn are found in the most available, exchangeable fraction.

With respect to long‐term effects acidification of poorly buffered sludges after disposal on land is probably the most important factor affecting metal associations and mobility. For many metal examples a linear relationship has been found between decreasing pH values and increasing dissolved metal concentrations. To quantify these relationships and for better comparison of samples a simple test procedure is proposed which is based on pH differences before and after addition of acid.     

PIXE characterization of PM10 and PM2.5 particulates sizes collected in Ikoyi Lagos,Nigeria

Ambient concentrations of PM₁₀ (x?≤?10?µm) and PM_2.5 (x?≤?2.5?µm) particulate fractions collected from Ikoyi Lagos, Nigeria, as well as their elemental compositions are presented in this study. Both size-segregated fractions were collected using a double staged ‘Gent’ stack filter unit sampler. Elemental characterizations of dust laden filters were carried out using proton-induced X-ray emission (PIXE) technique. Twenty-two elements (Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Pb, Br, Rb, Sr, Zr, Ag, Cd, and Ta) were detected as well as their concentrations and correlations were determined for both particulate size fractions. Their correlation matrix result indicates that some of the trace elements detected could have common source origins or similar chemical properties. The results were similar to the levels observed in moderately polluted urban areas and there is need for source identification and apportionment using receptor models in future studies.     

一株高效异养硝化菌的分离、鉴定及其氨氮去除特性

以丁二酸钠为唯一C源,从垃圾渗滤液活性污泥中富集、分离及筛选出一株高效的异养硝化菌,通过形态观察、生理生化特征及16S rDNA序列分析,对分离菌株进行了鉴定,同时对其硝化功能和氨氮去除特性进行了研究.结果表明,分离到的异养硝化菌为假单胞菌属(Pseudomonas sp.),命名为XS76,其GenBank登录号为(JQ934897).该菌经过24h培养,有约60%的氨氮转化为胞内氮,35%左右的氨氮被去除,仅有少量硝酸盐氮的积累,没有羟胺和亚硝酸盐氮的积累.碳源、有机氮源、C/N比、温度等因素均对氨氮去除有较大的影响,在接种量为4%、丁二酸钠为碳源、硫酸铵为氮源、C/N 15、转速180~200r/min、pH 6~9及温度为34℃,氨氮负荷为420 mg/L时处理效果最佳, 96 h氨氮去除率可达99.20%.显示了高效的氨氮去除效果,具有潜在的实际废水应用价值.     

产表面活性剂降解石油菌株产物性质及降解性能研究

微生物是组成生态系统的重要成员,在污染物去除中发挥着重要作用,是生物修复中的主力,然而在石油污染修复过程中,石油烃的疏水性会限制微生物对石油的降解,但一些微生物的细胞代谢物即生物表面活性剂,它是微生物在一定条件下代谢分泌产生的具有一定表面活性,集亲水基和疏水基结构于一分子的两亲性化合物,可以促进油的乳化,提高油的分散程度,增大菌株和油珠的接触机会,促进对石油烃的吸收和降解。在实验室分离得到了7株产表面活性剂石油降解菌株,经分子鉴定可知菌1和菌2都为粘质沙雷氏菌Serratia marcescens,菌3为居植物柔武氏菌Raoultella planticola,菌4,菌6和菌7都为克雷伯氏菌Klebsiella variicola,菌5为蜡状芽孢杆菌Bacillus cereus。主要研究了它们的生长与表面活性剂物质分泌状况的关系,发现随着时间增加,OD值随之增大,表面张力呈现下降趋势;并对菌株产物进行提取和薄层层析,离子型分析和红外光谱分析,初步判断其产物均为阴离子糖脂类;通过pH,初始油质量浓度,接种量和盐度4个单因素的变化研究菌1粘质沙雷氏菌,菌3居植物柔武士菌,菌5蜡状芽孢杆菌和菌6克雷伯氏菌对石油类物质降解能力,发现菌3居植物柔武氏菌和菌5蜡状芽孢杆菌降解性能较好;通过响应曲面法优化蜡状芽孢杆菌的降解条件,得出其最佳降解条件为pH为5.02,油质量浓度为3 g·L-1,接种量为1199.98μL,盐度为0.5 g·L-1时,在此条件下,菌株对石油的降解率为66.94%。     

黏结剂对污泥基颗粒炭性能的影响

以城市污水处理厂剩余污泥为原料,可溶淀粉、羧甲基纤维素、硅酸钠和硫酸钙为黏结剂,采用两步炭化法制备污泥基颗粒炭,探讨了黏结剂种类对样品性能的影响.结果显示:可溶淀粉样品(SSGAC-T)具有最大的比表面积和孔容,SSGAC-T、羧甲基纤维素样品(SSGAC-C)和硅酸钠样品(SSGAC-Si)含有丰富的微孔和中孔,硫酸钙样品(SSGAC-S)为典型的中孔吸附剂;样品的抗压强度均随浸泡时间的延长而降低,但SSGAC-S的抗压强度下降程度最小;4种黏结剂都使样品表面生成新的官能团,且样品的表面均呈酸性,它们的pHPZC分别为6.37、6.16、5.85和5.53;相同条件下,SSGAC-S对亚甲基蓝的饱和吸附量最高,为71.94mg/g;根据对污泥炭的表征,初步推测硅酸钠和硫酸钙能与碳发生化学反应.     

微生物絮凝剂MBF TS-1的表征

对筛选的一株絮凝剂产生菌Bacillus TS-1所产絮凝剂MBF TS-1采用UV- vis吸收光谱、FT-IR光谱、糖类颜色反应、动物急性毒性实验等进行了化学组成分析、表征和理化性质检测.结果证实,该絮凝剂为安全无毒、分子量为105-106的弱酸性多糖类物质,属环境友好型微生物絮凝剂.     

宜都市PM2.5与O3季节性分布特征及潜在源区分析

为了解宜都市PM_2.5与O₃的污染特征及潜在来源,利用宜都市2020年3月至2022年2月在线监测数据及气象数据,对宜都市PM_2.5与O₃质量浓度变化特征、气象影响因素及潜在源区进行了分析,结果表明:宜都市PM_2.5质量浓度冬高夏低,日变化呈双峰特征,O₃质量浓度夏高冬低,日变化呈单峰特征。高湿、静稳的气象条件以及较强偏北风作用下的区域污染传输对PM_2.5污染有重要影响,高温以及中湿度对O₃污染过程有重要作用。春、夏、秋季偏南方向气流轨迹占主导,且携带较高的污染物浓度,冬季来自湖北东北及西南方向的气流占比较高且携带的PM_2.5浓度较高;宜都市PM_2.5、O₃的潜在源区具有季节性差异,总体来看,主要分布在河南南部、湖北东部及湖南的北部区域。     

γ-Al_2O_3负载Ni、Fe催化剂同时脱硫脱硝

采用浸渍法制备了不同负载量的Ni(x)Fe(y)/γ-AL2O3催化剂,通过XRD、H2-TPR、BET和SEM对催化剂进行表征,使用微型催化反应装置考察催化剂在以CO作为还原气时,同时脱硫脱硝的催化活性。结果表明,Ni O和Fe2O3做为活性组分可以很好地分散在γ-Al2O3载体上,并且不破坏其结构;Ni(8)Fe(2)/γ-Al2O3催化剂有最佳的脱硫脱硝活性,脱硫率达到96.55%,脱硝率达到97.92%。     

Sample preparation and biomass determination of SRF model mixture using cryogenic milling and the adapted balance method

The biogenic fraction of a simple solid recovered fuel (SRF) mixture (80 wt% printer paper/20 wt% high density polyethylene) is analyzed with the in-house developed adapted balance method (aBM). This fairly new approach is a combination of combustion elemental analysis (CHNS) and a data reconciliation algorithm based on successive linearisation for evaluation of the analysis results. This method shows a great potential as an alternative way to determine the biomass content in SRF. However, the employed analytical technique (CHNS elemental analysis) restricts the probed sample mass to low amounts in the range of a few hundred milligrams. This requires sample comminution to small grain sizes (<200 μm) to generate representative SRF specimen. This is not easily accomplished for certain material mixtures (e.g. SRF with rubber content) by conventional means of sample size reduction.This paper presents a proof of principle investigation of the sample preparation and analysis of an SRF model mixture with the use of cryogenic impact milling (final sample comminution) and the adapted balance method (determination of biomass content). The so derived sample preparation methodology (cutting mills and cryogenic impact milling) shows a better performance in accuracy and precision for the determination of the biomass content than one solely based on cutting mills. The results for the determination of the biogenic fraction are within 1–5% of the data obtained by the reference methods, selective dissolution method (SDM) and ¹⁴C-method (¹⁴C-M).