我国污水处理回用存在的问题及其对策

针对我国水环境面临的严峻现实,分析了污水处理回用中存在的问题,提出了加强宣传力度,合理选择污水处理厂的处理规模和处理工艺,制定和完善污水回用的有关政策法规及合理解决水价,建立可持续发展的污水处理回用管理体系,多元化筹集建设资金,发展污水回用(污水资源化)的多元模式的对策.     

均相Fenton氧化-混凝法强化处理印染废水

采用均相Fenton氧化—混凝法对印染废水进行了强化处理。结果表明,该法特别适用于处理同时含有亲水性和疏水性染料的印染废水,处理过程充分发挥了均相Fenton氧化和混凝的协同作用,对废水中的水溶性有机物、胶粒和疏水性污染物均有较好的去除效果。在印染废水初始pH4.0左右,H2O2、FeSO4·7H2O和絮凝剂聚硅酸氯化铝(PASC)的加入量分别为3.6,1.8,8mL时,处理后废水的色度降到35,COD降到103mg/L,去除率分别高达95%和94.3%,脱色效果显著。     

用次氯酸钠法处理选矿废水

采用次氯酸钠法处理铅锌硫化矿选矿废水,考察了废水初始pH、NaClO加入量及反应时间对选矿废水COD去除率的影响。在废水pH为4、NaClO加入量为100g/L、反应时间为30min的条件下,选矿废水的COD去除率可达到98．3％;当pH为11、反应时间为10min、NaClO加入量为1g/L时,选矿废水的COD去除率为39．4％。     

全白土催化剂生产废水的处理

用4种无机絮凝剂和3种有机絮凝剂进行了脱除全白土催化剂生产废水（简称废水）中固体悬浮物（SS）的实验研究。实验结果表明：在废水pH6．8条件下,无机絮凝剂和有机絮凝剂脱除废水中SS的效果均较差,用无机絮凝剂时的SS去除率低于26％,用有机絮凝剂时的SS去除率低于18％;废水pH对SS去除率的影响较大,当调节废水pH为8．0时,无机絮凝剂中硫酸铝脱除废水中的SS效果最好,在硫酸铝加入量为0．02mg／L、沉降时间为2h的最佳操作条件下,SS的去除率可达93％。     

用水解酸化池-膜生物反应器处理活性艳红X-3B废水

采用水解酸化池-膜生物反应器处理含活性艳红X-3B的模拟废水,研究了水力停留时间（HRT）对水解酸化池废水处理效果的影响,考察了水解酸化池-膜生物反应器对废水的处理效果及膜生物反应器中污泥沉降性能对膜污染的影响。实验结果表明：水解酸化池HRT为16h时,废水的可生化性最好,挥发性脂肪酸质量浓度与COD比值为0．5;HRT为17h时,废水脱色率达69％,而COD的去除率受HRT影响较小;膜生物反应器主要起去除废水中COD的作用;水解酸化池-膜生物反应器处理后废水的脱色率和COD去除率分别为83％和97％;膜生物反应器中活性污泥沉降性能的变化直接影响膜污染的速率。     

混凝—催化氧化法处理丁苯橡胶生产废水

以聚合氯化铝（PAC）、阴离子聚丙烯酰胺（PAM）为混凝剂,以H2O2-O3为氧化剂,采用混凝-催化氧化法处理对丁苯橡胶生产废水。考察了混凝剂种类及其加入量、废水pH对混凝处理效果的影响,氧化剂及其加入量、反应时间和废水pH对COD去除率的影响。实验得出的最佳工艺条件：混凝实验,废水pH为7、PAC和PAM加入量为400mg／L和4mg／L;催化氧化实验,废水pH为7～8、H2O2加入量为200mg／L、H2O2与O3的质量比为0．5。处理后,废水COD从860mg／L降至145mg／L,COD去除率达83．1％,出水水质达到国家二级排放标准。     

钢渣吸附-微波降解法处理碱性品红废水

研究了钢渣对碱性品红染料的吸附性能、影响因素以及微波对吸附在钢渣-焦炭上的染料的降解作用。实验表明,在中性条件下,钢渣对碱性品红具有优良的吸附性能,饱和吸附量可达到42．4mg／g。以钢渣处理质量浓度为100mg/L的碱性品红溶液,当固液质量比为1：50、振荡吸附1h后,染料溶液脱色率达97％。实验还表明,焦炭可吸收微波产生高温,用钢渣-焦炭混合物（质量比1：1）吸附染料后,以微波辐照可使物料达到665℃的高温,吸附的染料降解。吸附剂再生后重复使用4次,脱色率都达到95％以上。     

液膜分离技术处理含Cr6+废水的研究

采用液膜分离技术处理Cr^6＋质量浓度为200—1000mg／L的废水,考察了膜溶剂、载体、内水相、外水相、pH、乳水比（乳液与废水的体积比）等因素对处理效果的影响,通过正交实验得出最佳实验条件。结果表明,在膜溶剂为煤油、载体为三辛胺、内水相为氯氧化钠、氢氧化钠质量分数为2％、pn为1、乳水比为1：4的最佳条件下,Cr^6＋的去除率可达98．4％。     

Metals in vineyard soils of the Penedès area (NE Spain) after compost application

The application of organic wastes to improve soil physical characteristics in mechanized vineyards planted after land levelling is becoming a common practice in Mediterranean areas. It may be useful as an additional source of organic matter and nutrients, but these wastes could also have negative effects due to their metal content. The aim of the study was to evaluate the influence of compost application on soil metal contents in mechanized vineyard soils of the Spanish Mediterranean area, where this practice is repeated every three years. The study was carried out in a ten-year-old vineyard where the main soil type is Typic Calcixerept. Composted cattle manure was applied in alternate rows, at a rate of 40 Mgha(-1) dry-weight. Nine sampling points were located along the slopes of two plots: a levelled plot prepared for mechanization with large soil disturbance movements within the plot, and a plot of undisturbed soil. At each location, soil samples were taken in both treated and untreated soils. Total concentrations (digestion with aqua regia) and the extractable DTPA (Diethylene-triaminepentacetic)-CaCl2-TEA (Triethanolamine) fractions of Cu, Zn and Mn were analyzed in each sample. For Cu and Zn, the initial concentration was higher in the undisturbed plot. In both cases, total Cu and total Zn were positively affected by manure input and the concentration in treated soils was significantly higher than in untreated soil. For Mn, the initial concentration was higher in disturbed soils than in undisturbed ones, and although in both scenarios the concentrations increased with manure, no significant differences were found between treated and untreated soils. The extractable fraction also increased in treated versus untreated soils, although for Cu and Mn the extractable/total metal ratio was similar in treated and untreated soils. After one compost application, total metal contents increased significantly, particularly for Zn. Most of those metals are accumulated in the soil, due to the soil characteristics.     

Ultrasound and enzyme assisted biodegradation of distillery wastewater

Irradiation with ultrasound (US) and use of an enzyme (E) as pretreatment techniques were carried out to treat a complex effluent (distillery wastewater). These two techniques have been used alone as well as in combination and the efficacy of these techniques was tested by subjecting the effluent to subsequent aerobic biological oxidation (AO). When used alone, US exposure for 30 min and 2 h yielded the best COD reduction during the aerobic oxidation step (US+AO). For the enzyme when used alone, a pH value of 4.8 (corresponding to the optimum pH of the enzyme), a dose of 50 U and a pretreatment time of 24 h yielded better COD removal efficiency as compared to untreated effluent (aerobic oxidation alone). When used in combination, ultrasound followed by enzymatic pretreatment (US+E+AO) yielded the best COD removal efficiencies during aerobic oxidation as compared to the other combinations tested for the treatment of the distillery wastewater. A 4-fold increase in the initial oxidation rate was observed over the untreated batch for the integrated technique (US+E+AO). On the basis of the variation in the values of the biokinetic parameters it can be concluded that the type of pretreatment scheme affects the subsequent rate of the aerobic oxidation significantly.