DSD酸氧化缩合废水浓缩液回用试验研究

研究了DSD酸氧化缩合废水浓缩液回用到原生产过程的可行性。对DSD酸氧化缩合废水可采用萃取技术分离出其中97％的有机物，反萃产生的4－8倍的浓缩液返回到DSD酸生产中的氧化缩合单元后，可提高DNS酸的收率约7．43％，且不会明显影响产品的纯度，浓缩液8次循环磁用试验的结果表明，虽然DSD酸氧化缩合废水的COD从15000－20000mg/L提高到20000－29000mg/L，但没有显著持续增长的趋势，表明反应液中副产物的浓度得到了有效的控制。     

Novel Polymeric Materials from Biological Oils

A variety of novel polymeric materials ranging from elastomers to tough, rigid plastics have been prepared by the cationic copolymerization of regular soybean oil, low-saturation soybean oil, or conjugated low-saturation soybean oil with various alkene commonomers. Using appropriate compositions and reaction conditions, 70–100% of the soybean oil is covalently incorporated into the cross-linked polymer networks, contributing significantly to cross-linking during copolymerization. The resulting thermosets exhibit thermophysical and mechanical properties that are competitive with those of their petroleum-based counterparts. In addition, good damping and shape memory properties have been obtained by controlling the degree of cross-linking and the rigidity of the polymer backbone. New materials with similar characteristics have also been produced from other biological oils, including tung, and fish oils using the same technique. The new, more valuable properties of these bioplastics suggest numerous promising applications of these novel polymeric materials.     

Ring-Opening Polymerization of Cyclic Esters onto Liquefied Biomass

Ring-opening polymerization of cyclic esters (-caprolactone, -valerolactone, and l-lactide) onto liquefied biomass (LB) was conducted to obtain the polyester-type polyol and to regulate the characteristics of LB. IR and ¹H-NMR spectra of the obtained polyol showed that the polymerization was successfully conducted in the presence of acid catalyst, which is used in liquefaction. The molecular weight (M_w), hydroxyl value, and viscosity were controllable by changing the reaction conditions. Polyester-type polyurethane foams with a wide range of properties were prepared from the obtained polyol with the appropriate combinations of foaming agents.     

Ethoxylated Soybean Polyols for Polyurethanes

Soybean polyols prepared by ring opening reactions of epoxidized soybean oil with hydrogen active compounds (water, alcohols, organic or inorganic acids, thiols, hydrogen etc.) have a low reactivity in the reaction with isocyanates because the hydroxyl groups are secondary. This paper presents a simple and convenient method to increase the reactivity of soybean polyols with secondary hydroxyl groups by ethoxylation reactions with the preservation of triglyceride ester bonds. The method uses mild reaction conditions: low alkoxylation temperature of 35–45 °C, low pressure of 0.1–0.2 MPa (15–30 p.s.i.) and a superacid as catalyst (HBF₄). The new soybean polyols have a higher reactivity toward isocyanates in polyurethane formation due to the high percentage of primary hydroxyl groups. The primary hydroxyl content was determined by the second order kinetics of polyol reaction with phenyl isocyanate.     

聚合反应时间对聚酰亚胺基碳膜结构和性能的影响研究

目的 系统研究前驱体聚合反应时间对PI膜及其碳化、石墨化后薄膜结构和性能的影响规律。方法 通过调整聚合合成聚酰胺酸(PAA)溶液过程中的反应时间,制备石墨膜前驱体聚酰亚胺(PI)原膜,将不同工艺条件下制得的PI膜进行碳化、石墨化处理,得到高导热率石墨膜。利用扫描电镜、红外光谱、拉曼光谱仪和LFA激光闪射仪对制备的PI膜、碳化膜及石墨膜的微观结构和热导率进行检测。结果 随聚合反应时间的延长,PI膜酰亚胺化程度和石墨膜的石墨化程度及导热性能先增高、后降低。反应时间为3 h时,制得的石墨膜结构致密,石墨片层取向性好,导热性能最好,热导率可达765.2 W/(m.K)。结论 PI膜前驱体聚合反应时间显著影响PI膜酰亚胺化的程度和有序度,进而影响石墨膜的定向性和导热性能。     

聚硅氯化铝混凝剂中Al(Ⅲ)水解聚合历程及铝硅作用特性研究

采用共聚与复合两种制备工艺，制备出了系列具有不同碱化度和不同Ａｌ／Ｓｉ摩尔比的聚硅氯化铝混凝剂，分析研究了ＰＡＳＣ中Ａｌ（Ⅲ）的水解－聚合历程以及聚硅酸与铝水解聚合产物的相互作用，探讨了ＰＡＳＣ溶液的酸解聚。     

包埋类脂的吸附剂制备及吸附POPs性能

用丙酮作溶剂将三油酸甘油酯分散到醋酸纤维(CA)基体中,采用悬浮聚合的方法制备出了一种兼具亲水性,又能高倍富集持久性有机污染物的球形复合吸附剂。通过对分散剂的种类及其用量、悬浮介质的种类及其用量的研究,获得了球形复合吸附剂的最佳合成路线与工艺.球形吸附剂粒径为1～2mm。通过荧光分析和电镜扫描分析,表明三油酸甘油酯已被包埋到醋酸纤维基体中,并得到了均匀分散。采用七氯、狄氏剂、异狄氏剂、灭蚁灵为代表性的持久性有机污染物(POPs)。动力学吸附实验表明,当初始浓度为1μg/L时,在快速吸附阶段,溶液中80%的氯、狄氏剂、异狄氏剂可得到有效去除,但并没有达到吸附平衡。快速吸附完后,还在持续地进行慢速吸附。而对于灭蚁灵,吸附速度远远低于其他几种POPs。实验证明了吸附速度不仅与辛醇/水系数有关,而且还与有机污染物的分子结构有关。     

三元高吸油树脂的制备及其吸油性能

采用本体聚合法,以丙烯酸丁酯(BA)、苯乙烯(St)和甲基丙烯酸十八酯(SMA)为单体,反应型低聚硅氧烷(OSS)为交联剂,偶氮二异丁腈(AIBN)为引发剂制备了三元高吸油树脂,优化了制备条件,考察了其对不同有机溶剂的吸油性能,并对其进行了表征。实验结果表明:树脂制备的优化条件为BA,St,SMA,OSS,AIBN的质量分别占单体总质量的39.60%,39.60%,20.80%,0.21%,1.50%,于55℃下反应24 h;在该优化条件下所制备的树脂对氯仿的吸油率可达80.2 g/g;树脂对氯仿和二氯甲烷的吸油率远高于其他有机溶剂。表征结果显示,树脂形成了一定的网络结构,具有较好的耐热性、耐寒性和热稳定性。     

三维电极处理腈纶聚合废水的条件优化研究

采用填充粒状活性炭的三维电极处理腈纶聚合废水,考察实验条件对污染物去除效果的影响以及废水处理前后可生化性的变化.阳极为Ti/SnO₂-Sb₂O₃网状极板,阴极为网状钛电极,分别考察了停留时间、 电解电压、 pH值、 曝气量对废水中污染物去除效果的影响.结果表明,电解电压和pH值对废水有机物的去除率影响较大,在最优实验条件：电解电压为15V,pH值为3,曝气量400 mL/min的条件下电解120 min,腈纶聚合废水的COD、 TOC和丙烯腈的去除率分别为32.59%、 22.17%和89.70%,并且经过电解处理,废水BOD₅/COD值从0.02上升至0.42,可生化性显著提高,为生物处理提供了条件.     

化工生产事故预防信息系统研究

为指导操作人员正确地处理化工生产过程中的问题,防范人为误操作导致的事故发生,开发了以化工生产的危险与可操作性分析结果和典型事故原因分析结果为知识库的事故预防信息系统.系统实时在线监测化工生产过程中的关键变量,通过判定变量间的影响关系,实现对化工生产过程潜在危险的辨识、预警并给予实时操作指导,以确保生产安全,提高装置的生产效率.最后,以丙烯聚合工艺为例,在多功能过程试验控制平台上进行了验证,探讨了事故预防信息系统的应用方法.