基于多孔环形喷嘴的可燃爆粉尘分散特征的密度效应研究*

为了研究不同密度的可燃爆粉尘在内置多孔环形喷嘴的20 L爆炸特性测试装置中的分散特征,基于负载粒子流方法、耦合DPM动量平衡方程和时间平均 Navier Stokes控制方程组,实现3种不同密度的煤粉、铝粉和锆粉在20 L爆炸测试装置中粉尘分散全过程的数值模拟。研究结果表明:多孔环形喷嘴的分散较为均匀,但是约束管道末端存在局部粉尘残留区,致使爆炸仓内真实粉尘浓度远低于形式浓度;爆炸仓中心位置的最大湍动能随着粉尘密度的增加而减小,只有显著地变化粉尘密度才能展示区分度较高的浓度峰值和抵达浓度峰值的时间。     

环境对冲压发动机烟火点火器性能影响研究

为促进某型冲压发动机烟火点火器生产工艺的定型,在海南进行了高温、高湿热带海洋气候自然环境对点火器长期贮存性能影响的研究。点火器采取无包装的暴露试验和密封包装贮存试验2种方法,分别在户外暴露场、棚库和库房等3种环境条件下进行试验。通过试验得到环境温度变化对密封包装储存的点火器的绝缘电阻值、电阻性能均无明显影响,点火性能良好,玻璃钢、涂层等贮存性能良好,点火器的环境适应性良好等结论。     

XZKP型高效空塔喷淋烟气脱硫装置技术特点

介绍了XZKP型高效空塔喷淋烟气脱硫装置的技术原理、技术特点、中试及工业化试验的情况。该技术通过改进工艺和结构,在提高脱硫效率和脱硫剂循环利用率两项技术上成效显著,用户可在不增加装置投资的前提下,获得更高的效率和更低的运行成本。     

提高电子元器件使用可靠性的方法

针对实际工作中元器件使用可靠性方面存在的问题．本文通过在实际工作的经验积累和技术研究总结,在电子元器件的选择与检测控制等方面,提出了提高电子元器件使用可靠性的方法。实践证明,这些方法可以直接应用于电子元器件的工程选择与检测控制。     

1/f噪声源与其在半导体器件可靠性评估中的应用

1／f噪声,由于其能够反映器件的质量与可靠性参数,其研究受到重视。本文首先较为系统地介绍了1／f噪声源两种较为成熟的理论：迁移率涨落模型和载流子涨落模型,最后介绍了几个1／f噪声与半导体器件参数漂移相关的实例。     

井下采空区构筑物漏风实测装置研发及应用

为了实时动态监测采空区构筑物漏风情况,自主研发了一种井下采空区构筑物漏风实测装置。通过现场实测及应用,研究结果表明:风流从工作面上进风口漏入采空区,而采空区中风流一部分通过与工作面之间的漏风流进入工作面下进风口,在下隅角位置附近形成一个涡流区;另一部分风流穿过沿空留巷构筑物进入留巷内,由于采空区的压实程度不同,采空区侧留巷内漏风速度曲线近似呈“L”型下降;通过收集分析留巷内漏风气体,其结果可反映采空区中瓦斯浓度分布情况,为采空区瓦斯治理提供了一种新的监测技术手段,且能有效地降低采空区瓦斯事故发生率,保证矿井的安全生产。     

油漆挥发分爆炸特性及浓度检测装置设计研究

为了实现对喷涂车间内挥发分浓度的检测,进行20 L球形爆炸特性测试实验,分析了油漆挥发分主成分及爆炸特性,根据油漆挥发分受热易挥发遇冷易凝结的物理特性、采样器采样原理、滤膜增重法测量原理以及基于单机片C++软件程序编写的电路智能控制技术,设计1种喷涂车间挥发分浓度检测装置。研究结果表明:油漆挥发分主成分具有爆炸性,且随着油漆颗粒物浓度增大,爆炸压力也增加。设计的装置对挥发分的采集率都在90%以上,总采集率为93.1%~98.9%,装置能够较为准确地检测挥发分浓度。     

Validation of a booted finite element model of the WIAMan ATD lower limb in component and whole-body vertical loading impacts with an assessment of the boot influence model on response

Objective: A novel anthropomorphic test device (ATD) representative of the 50th percentile male soldier is being developed to predict injuries to a vehicle occupant during an underbody blast (UBB). The main objective of this study was to develop and validate a finite element (FE) model of the ATD lower limb outfitted with a military combat boot and to insert the validated lower limb into a model of the full ATD and simulate vertical loading experiments.

Methods: A Belleville desert combat boot model was assigned contacts and material properties based on previous experiments. The boot model was fit to a previously developed model of the barefoot ATD. Validation was performed through 6 matched pair component tests conducted on the Vertically Accelerated Loads Transfer System (VALTS). The load transfer capabilities of the FE model were assessed along with the force-mitigating properties of the boot. The booted lower limb subassembly was then incorporated into a whole-body model of the ATD. Two whole-body VALTS experiments were simulated to evaluate lower limb performance in the whole body.

Results: The lower limb model accurately predicted axial loads measured at heel, tibia, and knee load cells during matched pair component tests. Forces in booted simulations were compared to unbooted simulations and an amount of mitigation similar to that of experiments was observed. In a whole-body loading environment, the model kinematics match those recorded in experiments. The shape and magnitude of experimental force–time curves were accurately predicted by the model. Correlation between the experiments and simulations was backed up by high objective rating scores for all experiments.

Conclusion: The booted lower limb model is accurate in its ability to articulate and transfer loads similar to the physical dummy in simulated underbody loading experiments. The performance of the model leads to the recommendation to use it appropriately as an alternative to costly ATD experiments.     

某退役后辐照装置的辐射水平监测与评价

依据国家相关标准对某退役后辐照装置周围的辐射水平进行监测与评价,通过数据评价得出该单位辐照装置退役场所未受到放射性污染,其退役后对环境的辐射影响可以忽略。     

半干法烟气脱硫除尘多级功能处理装置技术与应用

文中介绍了一种炉窑烟气调质、烟气除尘、烟气脱硫在一个单体结构中的一体化装置和在烟气除尘脱硫技术上的应用,并对该脱硫除尘装置与传统的半干法烟气脱硫除尘装置进行了比较。