铅酸电池系统的铅流分析

探求铅的工业流动规律,寻求环境管理的理论依据.在构建铅酸电池生命周期铅流图基础上,建立了铅酸电池系统与外部环境之间的联系,获得了铅的工业流动基本规律.结果表明,提高铅的生态效率,有助于铅矿资源保护和环境改善.要做到这一点,需要保持较高的铅循环率、较低的铅排放率.提出了铅流状况的评价指标.分析了中国铅酸电池系统中铅的流动.通过与瑞典某铅酸电池系统中铅的流动进行对比,发现由于中国铅的循环率低下、铅的排放率偏高、铅酸电池年产量持续增长等,造成了中国铅酸电池系统中铅的生态效率十分低下.结合中国铅业实况,分析了铅的循环率低下和铅的排放率偏高的成因,提出了改善对策.     

三维电极电化学反应器组合Fenton试剂深度处理焦化废水

采用三维电极电化学反应器组合Fenton试剂法对经过二级生化处理后的焦化废水进行深度处理。在三维电极参数一定的条件下,考察了影nfi]TOC去除率的影响因素,探讨了该反应体系的降解动力学及降解机理。正交试验结果表明,反应体系中各参数的最佳值分别为p（H202投加量）=300mg·L-1,pH3．4,反应时间为90min,c（FeS04-7H20投加量）为3．5mmol·L-1,TOC去除率可达到61．7％。焦化废水的降解反应表现为一级动力学。紫外吸收光谱分析结果,废水中有机物彻底发生了降解矿化,这为三维电极组合Fenton试剂工艺在焦化废水深度处理中的工程应用提供了一定的理论指导。     

Potassium carbonate-based ternary transition temperature mixture (deep eutectic analogues) for CO2 absorption: Characterizations and DFT analysis

•Addition of hindered amine increased thermal stability and viscosity of TTTM. •Addition of hindered amine improved the CO₂ absorption performance of TTTM. •Good the CO₂ absorption of recycled solvents after two regenerations. •Important role of amine group in CO₂ absorption of TTTM confirmed by DFT analysis. Is it possible to improve CO₂ solubility in potassium carbonate (K₂CO₃)-based transition temperature mixtures (TTMs)? To assess this possibility, a ternary transition-temperature mixture (TTTM) was prepared by using a hindered amine, 2-amino-2-methyl-1,3-propanediol (AMPD). Fourier transform infrared spectroscopy (FT-IR) was employed to detect the functional groups including hydroxyl, amine, carbonate ion, and aliphatic functional groups in the prepared solvents. From thermogravimetric analysis (TGA), it was found that the addition of AMPD to the binary mixture can increase the thermal stability of TTTM. The viscosity findings showed that TTTM has a higher viscosity than TTM while their difference was decreased by increasing temperature. In addition, Eyring’s absolute rate theory was used to compute the activation parameters (ΔG*, ΔH*, and ΔS*). The CO₂ solubility in liquids was measured at a temperature of 303.15 K and pressures up to 1.8 MPa. The results disclosed that the CO₂ solubility of TTTM was improved by the addition of AMPD. At the pressure of about 1.8 MPa, the CO₂ mole fractions of TTM and TTTM were 0.1697 and 0.2022, respectively. To confirm the experimental data, density functional theory (DFT) was employed. From the DFT analysis, it was found that the TTTM+ CO₂ system has higher interaction energy (|ΔE |) than the TTM+ CO₂ system indicating the higher CO₂ affinity of the former system. This study might help scientists to better understand and to improve CO₂ solubility in these types of solvents by choosing a suitable amine as HBD and finding the best combination of HBA and HBD.     

不同类型竹种光合特性的比较研究

光合作用是植物生长和物质积累的基础,其光合特性是高光效竹种选育的重要生理指标。为了更好开发利用我国丰富的竹种资源,确定不同类型竹种的光合性能,掌握其合成有机同化物的能力是必须探索的一个重要问题。文章采用Li-6400光合测定仪,通过对不同地下茎类型的6个竹种光合参数和光响应的测定分析,进一步探讨不同类型竹种存在差异的生理基础,以期对不同类型竹种的选育和经营管理提供依据。试验结果表明:不同竹种净光合速率(Pn)差异显著,大木竹Bambusa wenchouensis(Wen)Q.H.Dai的净光合速率最高,Pn值平均达到8.379μmol·m-2·s-1,毛竹Phyllostachys heterocycla cv.pubescens和雷竹P.praecox cv.prevernalis次之,斑苦竹Arundinaria oleosa和苦竹Pleioblastus amarus最低,总体呈现丛生竹>散生竹>混生竹的趋势,1～2 a生竹净光合速率高于3～4 a生竹,但没有显著差异。气孔导度(Cond)、胞间C02浓度(Ci)、蒸腾速率(Tr)综合说明丛生竹的光合固碳能力最强,其中蒸腾速率与气孔导度与净光合速率关系最为紧密,是影响净光合速率的主导因子。光响应曲线表明当光强刚开始增强时,各竹种间差异较小,但随着光强的继续增加,不同竹种出现很大的差异,其中绿竹Dendrocalamus.oldhami(Munro)Keng的潜在光合能力最高,远高于其他竹种,同样表现为丛生竹>散生竹>混生竹,进一步说明丛生竹种较强的光合固碳能力,从而为今后不同类型竹种,尤其是优良丛生竹种的筛选和开发利用提供理论参考。     

温度和pH值对活性污泥法脱氮除磷的影响

温度和pH值是影响污水脱氮除磷效果的2个重要因素.试验采用连续搅拌槽式反应器(continuous stirred tank reactor,CSTR),通过对不同温度和pH值条件下的硝化、反硝化、释磷和吸磷反应速率的测定,总结出温度和pH值对活性污泥生化反应速率的影响规律.试验表明,硝化和反硝化速率随温度的升高而加快.在5℃和33℃时,硝化速率分别为0.01 kg NH4 -N/(kg VSS·d)和0.28 kg NH4 -N/(kg VSS·d);在5℃和30℃时,反硝化速率分别为0.097 kg NO3--N/(kg VSS·d)和0.476 kg NO3--N/(kg VSS·d);但温度对吸磷和释磷速率的影响不大.pH值对硝化、反硝化、吸磷和释磷速率均有显著影响,在pH值为7.74时,硝化速率为0.095 kg NO3--N/(kg VSS·d);而在pH值为4.9和10.08时,硝化速率仅为0.005 kg NO3--N/(kg VSS·d)和0.006 kg NO3--N/(kg VSS·d).在pH值为7.85时,反硝化速率达到最大值0.36 kg NO3--N/(kg VSS·d);而在偏酸性和碱性条件下,反硝化速率显著下降.     

聚二甲基二烯丙基氯化铵与聚合硫酸铁复合絮凝剂的制备及应用研究

在一定温度下 ,将聚二甲基二烯丙基氯化铵 (PDMDAAC)溶解在聚合硫酸铁 (PFS)中 ,制成稳定的均相复合溶液。采用FT IR和X 射线衍射对其固体结构进行了分析。考察了液体复合絮凝剂的稳定性和固体复合絮凝剂的吸湿溶解性能 ,及其对生活污水的处理效果。结果表明 :在 6 0℃以下制备的液体复合絮凝剂具有良好的稳定性 ,固体复合絮凝剂具有良好的溶解性和比PFS更强的吸湿性 ;复合絮凝剂不是由PDMDAAC与PFS简单的机械混和 ,而是互相融合的复合体系 ;具有比PFS更优的去污性能和与PFS类似的较宽的最佳投药范围和 pH适用范围。对浊度和COD分别为 10 5 2和 187 5mg/L ,pH值为 7 5 9的生活污水 ,复合絮凝剂中Fe3 + 和PDMDAAC最佳用量分别为 5 4 .15和 4 2 7mg/L ,对COD的去除率为 77 14 % ,比PFS在用量为 81 2 2mg/L时的最佳效果高 12 %。     

琼脂碳源生物反硝化去除水源水中硝酸盐

针对受硝酸盐污染的水源水,以琼脂为反硝化细菌的碳源和微生物载体,通过生物反硝化作用脱除水源水中的硝酸盐,并利用曝气生物滤池(BAF)去除琼脂反应器出水中残留的少量CODMn和NO2--N等污染物。实验结果表明,水源水自然接种的条件下,可以顺利启动琼脂反应器;在温度为25℃左右,琼脂反应器在进水NO3--N约25 mg/L、水力停留时间1.5 h时,能获得70%的硝酸盐氮去除率;曝气生物滤池在水力停留时间0.5 h、气水比2.8时,可控制最终出水的CODMn和NO2--N分别在5.0 mg/L和0.10 mg/L以下;琼脂反应器的脱氮效果与温度、进水NO3--N浓度及水力停留时间等有关。研究指出,琼脂反应器与曝气生物滤池构成的组合系统能较好地脱除水源水中的硝酸盐并且能控制最终出水水质,不会导致二次污染,从而获得合格的饮用水源水。     

美国某给水厂处理工艺及净水效果

介绍了美国某给水厂的臭氧-生物活性炭深度处理工艺、主要构筑物、设计参数和运行效果。实验结果表明:原水中TSS、BOD5、COD、UV254和浊度平均值分别为18.25 mg/L、5 mg/L、7.34 mg/L、0.08和17.38 NTU,经过系统处理后的出水指标分别为1.33 mg/L、2 mg/L、0 mg/L、0.01和0.86 NTU,相应的平均去除率分别为88%、60%、100%、88%和81%。净水效果明显,五项常规指标均满足我国《生活饮用水卫生标准》(GB5749-2006)使用要求,这种深度处理技术及设计思路值得国内给水处理行业参考借鉴。     

铁镍改性膨润土对废水中有机污染物的吸附性能研究

以钠基膨润土为原料,制备了铁镍无机改性土和铁镍有机复合改性土,并应用于造纸废水的处理,探讨了改性土用量、废水pH值、搅拌时间等因素对COD去除率的影响,通过正交实验对实验条件进行了优化.结果表明:铁镍有机复合改性土和铁镍元机改性土对废水的处理效果明显好于原土;膨润土的用量、废水的pH对COD的去除率影响较大;对于铁镍无机改性土,吸附剂用量为12g/L,溶液pH=2,吸附时间为10 min时,对废水中COD的去除率为54.06%;对于铁镍有机复合改性土,吸附剂用量为14g/L,溶液pH=3,吸附时间为20 min时,对废水中COD的去除率为70.10%.     

Escherichia coli inactivation by pressurized CO2 treatment methods at room temperature: Critical issues

This study aims to increase the inactivation efficiency of CO_2 against Escherichia coli under mild conditions to facilitate the application of pressurized CO_2 technology in water disinfection. Based on an aerating-cycling apparatus, three different treatment methods(continuous aeration, continuous reflux, and simultaneous aeration and reflux) were compared for the same temperature, pressure(0.3–0.7 MPa), initial concentration, and exposure time(25 min). The simultaneous aeration and reflux treatment(combined method) was shown to be the best method under optimum conditions, which were determined to be 0.7 MPa, room temperature, and an exposure time of 10 min. This treatment achieved 5.1-log reduction after 25 min of treatment at the pressure of 0.3 MPa and 5.73-log reduction after 10 min at 0.7 MPa. Log reductions of 4.4 and 5.0 occurred at the end of continuous aeration and continuous reflux treatments at 0.7 MPa, respectively.Scanning electron microscopy(SEM) images suggested that cells were ruptured after the simultaneous aeration and reflux treatment and the continuous reflux treatment. The increase of the solubilization rate of CO_2 due to intense hydraulic conditions led to a rapid inactivation effect. It was found that the reduction of intracellular p H caused by CO_2 led to a more lethal bactericidal effect.