美缝剂TVOC释放量与释放规律的测试与分析

提出了环境舱法测试美缝剂总挥发性有机化合物(TVOC)释放量的方法,对市场常见的美缝剂产品的TVOC进行了测试,并研究了美缝剂的TVOC释放规律和主要污染物.同时对美缝剂的甲醛释放量进行了测试.通过对16种环氧树脂美缝剂产品的数据分析显示,美缝剂产品的甲醛释放量风险较低;75%的产品在第7天的TVOC释放量可达到500μg·m^-3以下.但个别产品在28 d时仍有明显的VOC释放,显示其具有长期缓慢释放的特点.美缝剂释放的主要污染物为苯甲醛与苯甲醇,个别产品检出有甲苯和邻苯二甲酸酯类物质.     

Permeability of Medical Gloves to Mono- and Dimethacrylate Monomers in Dental Restorative Materials

Dental personnel manually handle methacrylate-based restorative materials, which can cause skin irritation and allergies. The protection given by different types of medical gloves is not well known. Breakthrough time (BTT, min) was used as a measure of protection according to a European standard, using 2 test mixtures consisting of respectively 3 and 5 monomers. Fourteen gloves representing natural rubber latex, synthetic rubber, and synthetic polymeric material were tested. The BTT ranged from some minutes to more than 2 hrs for the 4 monomers with a molecular mass less than 300. The longest protection was recorded for Nitra Touch (nitrile rubber), Tactylon (synthetic rubber), and Metin (PVC).     

环氧丙烷储罐空气泡沫灭火试验研究

环氧丙烷为低沸点水溶性可燃液体,由于其饱和蒸汽压大,灭火困难,此前,国内外未对环氧丙烷进行过大型工程应用灭火试验研究。为研究空气泡沫对环氧丙烷储罐的灭火性能,分别对环氧丙烷进行了0．25m^2油盘探索性试验、1．73m^2油盘泡沫灭火剂选型试验和直径3．5m储罐工程应用灭火试验。试验结果表明,空气泡沫难以扑灭环氧丙烷储罐火灾,在直径3．5m储罐上,虽然采用了灭火性能较好的泡沫液,且使用了较大的供给强度和较长的供给时问,但仍难灭火。在试验基础上,对环氧丙烷储罐的消防要求提出了建议。     

沿海钢结构设施的防腐研究

针对沿海钢结构设施的腐蚀情况及目前常用防腐涂料的性能,优选了3种重防腐涂料——环氧富锌底漆、环氧玻璃鳞片中间漆、聚氨酯面漆。讨论了环氧树脂、锌粉、玻璃鳞片、聚氨酯改性树脂的选择方法,并提出了适合涂料涂装的表面处理技术和施工工艺。     

混凝-生物强化联合处理环氧树脂高盐废水

环氧树脂高盐废水是目前较难处理的工业废水之一.采用混凝联合生物强化工艺:通过混凝过程进行预处理后,投加嗜盐菌进行生物强化考察盐度变化对系统降解有机物的影响以及污泥性状的变化情况.结果表明,当废水中氯离子浓度达到驯化目标10 g/L时,系统对COD的去除率仍稳定在85％左右;以没有投加嗜盐菌的反应器为对照组,在进水COD平均浓度为550 mg/L左右,氯离子浓度由12 g/L增至21 g/L时,对照组COD平均去除率由82％降至60％以下,而投加了嗜盐菌的反应器(投加组)则仍保持在85％以上;此外,盐度的变化同时影响污泥的活性及其沉降性能,随着盐度增大,两组中的污泥活性均有所降低,但投加组的污泥活性相对较高,其污泥的沉降时间和污泥体积指数(sludge volume in-dex,SVI)值也较低.采用本工艺处理环氧树脂高盐废水,使得生物处理过程能够长期稳定运行,且能够保持较高的耐盐度和COD去除率.     

聚环氧琥珀酸对锰渣中砷的萃取

以锰渣为材料,用聚环氧琥珀酸(PESA)作为萃取剂,研究PESA在不同pH、萃取剂浓度、土液比下对砷(As)的萃取效果。实验结果表明,与丙烯酸/马来酸酐共聚物(MA/AA)相比较,PESA对锰渣中As有优良的萃取效果。在萃取体系条件为pH=1、萃取剂浓度50 mg/mL、土液比1∶200、搅拌60 min并浸泡过夜时,PESA对砷的萃取率可达78.3%。实验还发现,PESA对三价砷和五价砷均有螯合萃取作用,对砷的萃取无价态的选择性。     

Time course of isocyanate emission from curing polyurethane adhesives

The time course of isocyanate emission from curing polyurethane (PUR) resins and adhesives was studied in two different emission test chambers. The measured emissions were strongly dependent on the type of experiment. The adhesives under investigation contained different types of diisocyanates and are used for different applications, e.g. for fixing of textile floor coverings. The influence of the curing mechanism on emission was studied by comparing the emission curves of one-component adhesives (OCA) and two-component adhesives (TCA). For TCA, the decrease in isocyanate emission was found to follow a two-step process during curing. In the first step, the emission is dominated by surface evaporation, and the decay of emission is mainly caused by the decrease in monomer content due to reaction. In the second step, the release is limited by internal diffusion. The influence of monomer reactivity on the emission profile could be demonstrated for 2,4′- and 4,4′-MDI. The less-reactive 2,4′-MDI caused prolonged emission. A strong dependence of emission rates on temperature and adhesive viscosity was also obvious. The evaluation of emission rates of different commercially available PUR adhesives showed the highest emission from systems that are applied at high temperatures. The high reactivity of diisocyanates requires special techniques for sampling and analysis. Therefore, an analytical method using HPLC–MS/MS was developed that enables limits of quantitation of <5 ng/m³ with a sampling volume of 100 l.     

基体表面状态对硅烷环氧杂化树脂涂层/2024铝合金间附着力影响

目的研究不同表面状态对硅烷环氧杂化树脂涂层/2024铝合金间附着力影响规律。方法结合硅烷环氧杂化树脂涂层的综合性能与实际应用情况,选取4种常见的预处理方式来改变基体表面状态,采用拉拔测试仪测试不同基体表面状态(基体表面p H值、基体表面粗糙度、基体表面能),涂层/基体间的附着力值,研究基体表面状态对该涂层/基体间附着力的影响关系。结果基体表面状体影响涂层附着力的根本原因是基体表面能、基体表面p H值和基体表面粗糙度。结论对于硅烷环氧杂化树脂涂层,其表面处理方式可用热碱清洗方法代替传统铬酸盐钝化;当硅烷环氧杂化树脂涂层喷涂厚度为30μm时,将铝合金基体表面粗糙度控制在Ra=4.75μm左右,可保证涂层有好的附着性,附着力值为8.84 MPa。     

活性污泥法+接触氧化法工艺处理高盐度环氧丙烷生产废水的试验研究

采用活性污泥法和接触氧化两段工艺对高含盐的环氧丙烷生产废水进行处理，同时研究了不同水力停留时间的处理效果和不同的盐度对处理效果的影响。试验结果表明CODcr的去除率可以达84．38％，出水CODcr＜160mg／L，pH＜8。     

改性环氧树脂灌封提高铝电解电容器的三防性能

针对铝电解电容器出现的三防问题，通过对环氧树脂进行改性，提高环氧树脂的防护能力，并以此对铝电解电容器进行灌封，经过三防试验检验，结果表明采用改性环氧树脂灌封能效提高铝电解电容器的三防性能。