Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

焦作市区大气污染状况与防治措施

根据“九五”期间焦作市区的大气污染监测资料，对市区大气污染状况进行了分析和评价，并对其成因进行了分析，提出了一些具体的防治措施。     

乌鲁木齐市可吸入颗粒物(PM10)与总悬浮颗粒物(TSP)的相关性规律浅析

通过对乌鲁木齐市的PM10和TSP数据的对比分析，找出PM10在TSP中所占比率（分担率）在采暖季和非采暖季的变化范围，从而使过去采集的TSP数据与PM10数据有一定的可比性，保证监测数据的连续可比。     

Prediction of Leachate Level in Kimpo Metropolitan Landfill Site by Total Water Balance

Kimpo metropolitan landfill has received various kinds of wastessince January 1992. The leachate level was measured to be 10.3 m in May 1995 and the level increased to 12.2 m in August 1996. Therefore, to prove the reason for the increasing leachate level, we calibrated hydraulic conductivity of each waste andintermediate layer using the HELP (Hydrologic Evaluation ofLandfill Performance) model. The leachate generation data measured from February 1993 to October 1995 was used in the model calibration. As a result of a model calibration, we obtained anaverage infiltration ratio and used this in analysis of the total water balance to predict elevation of leachate level. Main causes of the elevation of the leachate level were the high water content of the waste and the degradation of the leachate-drainage system caused by the subsidence of a naturalbarrier layer.     

Monitoring of Seasonal Vegetables for Pesticide Residues

Market samples (60) of six seasonal vegetables were monitoredduring 1996–1997 to determine the magnitude of pesticidalcontamination. The estimation of insecticide residuesrepresenting four major chemical groups i.e. organochlorine,organophosphorous, synthetic pyrethroid and carbamate, was doneby adopting a multiresidue analytical technique employingGC-ECD and GC-NPD systems with capillary columns. The testedsamples showed 100% contamination with low but measurableamounts of residues. Among the four chemical groups, theorganophosphates were dominant followed by organochlorines,synthetic pyrethroids and carbamates. About 23% of the samplesshowed contamination with organophosphorous compounds abovetheir respective MRL values. More extensive studies coveringdifferent regions of Haryana state are suggested to get a clearidea of the magnitude of vegetable contamination with pesticideresidues.     

Modelling of Materials Policies

This paper discusses the REAP1 model and its application for the analysis of CO₂ reduction and waste management policies for Japanese petrochemicals. The pros and cons of this modelling approach in comparison to other tools is elaborated. This is followed by a discussion of the model code and the modelling results. The results show that CO₂ policies can have significant impacts on waste flows and waste policies can have significant CO₂ benefits. As a consequence both effects must be considered in policy assessment. Pricing instruments are recommended instead of regulations because of the complex physical relations in the materials life cycle that extend beyond sector boundaries. A taxation approach is superior to a subsidy approach because rebound effects can be avoided.     

Preliminary air pollution monitoring in San Miguel, Buenos Aires

Passive diffusion samplers were employed in San Miguel(Buenos Aires Metropolitan Area) for a preliminary airpollution monitoring. The highest loads were observedin downtown, compared with an urban background site.Total suspended particulate matter (TSPM) varied from0.257 to 0.033 mg cm^-2 month^-1; dust was examinedfor particle nature and size distribution. A similartrend was observed for nitrogen dioxide (NO₂) andTSPM spatial distribution, suggesting that traffic isthe major pollution source. Sulphur dioxide (SO₂)values were low and rather homogeneous. Levels for theinvestigated pollutants are below EPA's guide linevalues. Geographic (flat area, near to Rio de LaPlata) and climatologic factors (rainfalls andvariable wind directions) contribute to disperse pollutants.     

用工业废水排放量预测地面水CODMn灰色方法研究

ＧＰＭ（１）灰色生长曲线常被用于等距时序环境系统的分析建模、非等距摆动空间序列方面的应用尚未报道。本文研究提出了将非等距摆动空间序列经过等距化处理的ＧＰＭ（１）线性回归优化建模方法采用该方法所建的非等距ＧＰＭ（１）模型用于工业废水量预测地面水ＣＯＤＭｎ的实例表明，该方法简捷，方便、精度高于回归分析，有较大实用价值。     

采样系统中金属氧化物对SO2测定值影响分析

通过实验与实际工程相结合，定量描述了大气采样系统中金属氧化物的存在对ＳＯ２测定值的影响，并阐述了其反应机理，提出了相应措施。     

Modeling photocatalytic destruction of the organic contaminants in continuous stir flow reactor

Thin-film technique is becoming an industry standard for the preparation of TiO₂-based photocatalyst for organic destruction. The catalyst provides several advantages over the conventional powder TiO₂ in the treatment of wastewater and groundwater. In this study, a continuous stir flow reactor model is developed capable of describing the photocatalytic process. The model incorporates the following fundamental mechanisms: adsorption, diffusion, liquid-film transfer, UV attenuation, and photocatalytic reaction. All of the simulation results indicate that there exists a highly nonlinear relation between each of these parameters and the destruction rate. Various incident light intensities also are incorporated to simulate the energy efficiency. The simulations illustrate that the photocatalytic model can be used to elucidate the effect of process variables. It is also possible to “custom-design” a catalyst for the treatment of a particular waste stream.