爆炸荷载作用下钢筋混凝土防爆墙动力响应研究

为了研究钢筋混凝土防爆墙的抗爆能力,采用有限元分析方法对不同纵向配筋率、不同高跨比、不同厚度的墙体在爆炸动态荷载作用下的动力响应进行研究,对各种不同设置的钢筋混凝土防爆墙的抗爆性能进行评估。结果表明:减小高跨比对提高钢筋混凝土防爆墙的抗爆能力最为重要,提高纵向配筋率,增加厚度都能增加防爆墙的抗爆能力。     

Assessment of sediment contamination in Casco Bay, Maine, USA

The current status of contaminant concentrations in Casco Bay, decadal trends of these contaminants and changes in their geographical distribution are assessed using sediment samples collected approximately 10 years apart. In general, regulated contaminants appeared to be decreasing in concentration. Total PAH and dioxins/furans concentrations did not significantly change over this period. Total organochlorine pesticides, 4,4-DDE, 4,4-DDD, total DDT, PCB, tributyltin and total butyltin decreased in concentration. Trace element concentrations in sediments decreased at the majority of the sampling sites for chromium, nickel, and selenium while arsenic, cadmium, copper, lead, mercury, silver, and zinc remained relatively constant. None of the contaminants measured has increased by more than a factor of 2. Selected sites located in the Inner Bay, where concentrations are higher and new inputs were more likely, showed increased concentrations of contaminants. Most contaminants were not found at concentrations expected to adversely affect sediment biota based on ERL/ERM guidelines.     

吸力式桶形基础多桶组合结构承载力特性研究

海洋采油平台结构中一般采用多桶组合基础型式,然而迄今对多桶组合结构尚缺乏理论分析和实验研究。本文针对我国第一座吸力式桶形基础采油平台CB20B,基于单桶基础在复合加载模式下的承载力特性,建立了双桶、四桶组合基础的三维有限元数值计算模型,探讨了对称多桶基础结构与单桶基础结构的承载力特性之间的相互关系,阐述了不同桶间距的多桶组合结构地基破坏机制,为工程设计提供参考依据。     

基坑开挖对临近地基极限承载的影响性状数值分析

采用弹塑性有限元分析方法,分析了悬臂式排桩支护的基坑开挖对邻近地基条形基础下极限承载力的影响性状。主要考虑了在基坑开挖深度、荷载与基坑的距离、荷载宽度、支护刚度等因素的影响下地基极限承载力的减损性状。研究表明,基坑开挖深度H较浅时,对地基极限承载力P_u的影响较小,P_u随H的增大略有降低,随着开挖深度的增加,H对P_u值的影响显著增大,且P_u值显著降低;当L/H≤2时,荷载与基坑的距离L对地基极限承载力P_u的影响很大,地基极限承载力P_u随L的减小而显著减小,当L/H>3时,L的影响逐渐减小,且P_u逐渐趋近于无基坑开挖时的值;P_u随地基荷载作用宽度B的增大而呈线性增大;支护桩的位移越小,P_u值越接近无基坑开挖时的地基极限承载力。     

基于可拓物元模型的安全经济开采评价指标体系的构建及应用

首先根据安全经济开采的内涵,建立以人员安全、设施设备安全、开采环境安全、安全投资和安全管理为主要制约因素的安全经济开采评价模型,并运用改进的层次分析法确定人员可靠度对安全经济开采水平影响最大,开采环境可靠度影响最小。其次,采用函数拟合法、专家打分法、标准化打分法量化安全经济开采水平指标,并将安全经济开采水平划分为3个等级。最后,运用可拓物元模型方法,得出某铁矿安全经济开采水平为二级,无重大经济损失,与实际吻合。     

Validation of a booted finite element model of the WIAMan ATD lower limb in component and whole-body vertical loading impacts with an assessment of the boot influence model on response

Objective: A novel anthropomorphic test device (ATD) representative of the 50th percentile male soldier is being developed to predict injuries to a vehicle occupant during an underbody blast (UBB). The main objective of this study was to develop and validate a finite element (FE) model of the ATD lower limb outfitted with a military combat boot and to insert the validated lower limb into a model of the full ATD and simulate vertical loading experiments.

Methods: A Belleville desert combat boot model was assigned contacts and material properties based on previous experiments. The boot model was fit to a previously developed model of the barefoot ATD. Validation was performed through 6 matched pair component tests conducted on the Vertically Accelerated Loads Transfer System (VALTS). The load transfer capabilities of the FE model were assessed along with the force-mitigating properties of the boot. The booted lower limb subassembly was then incorporated into a whole-body model of the ATD. Two whole-body VALTS experiments were simulated to evaluate lower limb performance in the whole body.

Results: The lower limb model accurately predicted axial loads measured at heel, tibia, and knee load cells during matched pair component tests. Forces in booted simulations were compared to unbooted simulations and an amount of mitigation similar to that of experiments was observed. In a whole-body loading environment, the model kinematics match those recorded in experiments. The shape and magnitude of experimental force–time curves were accurately predicted by the model. Correlation between the experiments and simulations was backed up by high objective rating scores for all experiments.

Conclusion: The booted lower limb model is accurate in its ability to articulate and transfer loads similar to the physical dummy in simulated underbody loading experiments. The performance of the model leads to the recommendation to use it appropriately as an alternative to costly ATD experiments.     

走滑断层作用下X80管道设计应变规律和神经网络预测

走滑断层是埋地管道常见的地质灾害威胁,断层作用下管道会发生较大的拉压应变而失效。为得到X80管道的设计应变,基于有限元方法建立了走滑断层作用下管道的应变响应数值计算模型,模型使用壳单元模拟管道,非线性弹簧单元模拟土壤约束,采用西二线实际工程的管道应变影响参数范围,计算了管道的设计应变;为预测管道的设计应变值,基于以上参数化分析得到的4 817组设计应变结果,采用人工神经网络建立了管道设计应变预测模型。结果表明:该神经网络模型预测结果的最大相对误差小于10%,预测准确性良好,且该方法具有较高的计算效率,可以为断层作用下埋地管道的应变设计与评估提供参考。     

非柔性连接石化储罐配管温差应力分析与对策

储罐配管在温差作用下产生热位移会导致管壁产生热应力,未采用柔性连接的配管由于热应力集中作用可能发生破漏。针对与石油化工储罐非柔性连接的配管的安全问题,应用ANSYS有限元分析软件模拟计算石化企业典型配管的热应力分布;根据不同类型配管的分析结果,提出了工程技术与管理方面的针对性安全措施。研究结果表明:温差效应对石化储罐配管热应力影响显著,随内外温差的增加,配管应力集中的区域增大,最大热应力值增大;补偿措施能够改善配管的柔性,降低配管应力;约束载荷限制配管热膨胀从而增大配管应力;三通管是多根配管接合的区域,这种复杂管道交汇处会形成明显应力集中。研究结果对于提高石油化工非柔性连接配管安全性有一定的指导意义。     

抗压实验法厌氧颗粒污泥机械强度的测定及影响因素分析

通过首先对厌氧颗粒污泥样品进行筛分,然后测定其机械强度,解决了实际操作过程中现有抗压实验法出现的精确度与重现性较差的问题。通过对不同来源厌氧颗粒污泥样品机械强度的测定、对比分析发现,厌氧颗粒污泥的机械强度大小与反应器的规模、反应器所采用水力负荷存在一定的正相关性,且与其主要金属元素（Ca、Fe和Mg）含量的大小存在着密切的关系。     

基于元素毒性赋值的模糊数学环境质量评价

利用模糊数学方法,根据元素毒性的大小进行权重赋值,对成都经济区近地表大气尘进行地球化学环境质量评价。结果显示：不同城市中,成都、乐山、眉山的大气环境质量较好,处于一级清洁级别;眉山、雅安的大气环境质量处于二级安全级别;德阳的大气环境质量已经处于三级警戒级。不同地区中,绵阳和眉山的大气环境质量较好,处于一级清洁级别;德阳和雅安处于二级安全级别,成都和乐山处于三级警戒级.