气相色谱-串联质谱法测定沉积物中多环芳烃

采用ASE法提取沉积物中16种多环芳烃,以固相萃取法净化提取液,用气相色谱-串联质谱法测定。通过优化测定条件,使方法在5.00μg/L~1 600μg/L范围内线性良好,方法检出限为0.15μg/kg~0.66μg/kg。空白石英砂的加标回收率为61.9%~121%,7次测定结果的RSD为2.6%~11.1%。     

Facilitating substance phase‐out through material information systems and improving environmental impacts in the recycling stage of a product

The amount of electrical and electronic products is increasing rapidly, and this inevitably leads to the generation of large quantities of waste from these goods. Some of the generated e‐waste ends up in regions with sub‐standard recycling systems and may be processed under poor conditions. During uncontrolled incineration, halogenated dioxins and furans can be generated from brominated and chlorinated compounds in the products. In order to reduce the health and environmental risks involved in the recycling stage of the life cycle of electronics, an effective design‐for‐environment process must be established during the product development phase. Knowledge of the chemical substances in the product is crucial to being able to make informed decisions. Through full knowledge of the material content of procured components, phase‐outs of unwanted substances, such as halogenated substances, can be performed in an effective manner. Therefore, information is the key to success in phasing‐out substances; facilitating compliance of legal provisions for manufacturers of electrical and electronic devices; and improving the environmental footprint of products as they reach the end of the life cycle. After an introduction to the challenges of electronics waste management, this paper describes supply chain information systems and how they are used to facilitate substance phase‐outs in the electronics industry. Sony Ericsson has been working with phase‐outs of unwanted substances since it was founded in 2001. Through the introduction of a material declaration system that keeps track of all substances in the components used in the company's products, Sony Ericsson has been able to replace unwanted substances to improve environmental impacts at the recycling stage of a product.     

曝气强度对同时硝化反硝化（SND）脱氮过程中N2O排放的影响

为了控制污水脱氮中N2O排放,在不同曝气强度下研究了好氧硝化段同时硝化反硝化（SND）系统的N2O排放特性,并采用PCR—DGGE技术分析微生物群落特征。结果发现,随着曝气强度的增强,系统总氮去除率下降,但脱氮中N2O—N所占比例则上升,实验中从低到高3个曝气强度下,总氮去除率分别为80．01％、65．28％和58．62％,脱氮中N2O—N所占的比例为1．89％、7．84％和9．20％。PCR—DGGE分析显示,和低曝气强度下相比中、高曝气强度下系统微生物群落发生明显变化,但中曝气强度和高曝气强度下系统微生物群落表现出较高相似性。这表明,不同曝气强度下系统N2O排放受到氮素转化和微生物群落变化的影响。适宜曝气强度不仅提高总氮去除率,还可有效控制N2O排放。     

锐钛矿-金红石混合晶型TiO2降解气相苯

用溶胶-凝胶法并通过控制煅烧温度合成不同晶相比的混合晶型纳米TiO_2,在紫外光光照下降解气相苯。考察了苯初始质量浓度、紫外灯光照强度和催化剂加入量对苯去除率的影响;探究了光催化降解气相苯的动力学特征。结果表明:450℃煅烧制备的催化剂降解苯效率最高,此催化剂金红石相质量分数为6.30%;在苯初始质量浓度为74.39 mg/m~3、催化剂加入量为7 g、光照强度为2.18 klux的最佳条件下反应84 min,苯去除率达99.73%;光催化降解率与光照强度之间符合0.5级动力学特征;当催化剂加入量为3 g时,单位时间单位质量催化剂降解苯的质量最多;苯的光催化降解反应均符合一级动力学方程。     

固相萃取-气相色谱法测定水样中马拉硫磷残留

采用C-18小柱萃取、毛细管柱分离、气相色谱氢火焰离子化检测器（FID）测定水样中的马拉硫磷,检测限为0．12μg／L。试验了样品流量和洗脱剂对回收率的影响,结果表明样品流量为6mL／min、二氯甲烷作洗脱剂时,回收率较好。测定蒸馏水、地下水和河水样品,相对标准偏差〈2．2％。加标回收率在79．0％-109％之间。     

固相萃取-气相色谱法测定饮用水中甲基汞

根据巯基棉在一定酸性条件下能定量吸附甲基汞的原理,利用多通道并联的固相萃取装置,采用气相色谱(ECD)方法测定饮用水中痕量甲基汞,考察了水样pH值对回收率的影响.方法在0.050 mg/L～1.00 mg/L范围内线性良好,当采样体积为1.0 L时,检出限为0.03 ng/L,标准样品与实际水样平行测定的相对标准偏差均...     

Hydrothermal liquefaction phase behavior of microalgae & model compounds in fused silica capillary reactor

A fused silica capillary reactor combined with a heating/cooling stage, a microscope and a digital camera were used to investigate phase behavior during the hydrothermal liquefaction of microalgae (Dunaliella tertiolecta) and model compounds, including soya protein and glycine, starch, glucose and xylose, stearic acid and palmitic acid. Bubbles were generated at 246°C and disappeared at 360°C upon heating when Dunaliella tertiolecta used as feedstocks. Moreover, liquid products were generated at 300°C upon heating and oily liquid products began to separate out at 250°C upon cooling. The phase behavior of soya protein was similar to that of the Dunaliella tertiolecta. Meanwhile, there only observed the bubbles generation during hydrothermal liquefaction of glycine. Heating the starch, glucose and xylose above 350°C generated black solids from carbonization. Stearic acid and palmitic acid only had the process of melting, dissolution, dispersion and precipitation.     

Flowering pattern of biodiesel plant Jatropha in frost- and drought-prone regions of Botswana

Jatropha has gained interest as a potential biodiesel feedstock. Nevertheless, its oil production decreases significantly in frost- and drought-prone regions. In this study, we characterized the flowering pattern of Jatropha in Botswana in the 2014/2015 season. Extensive springtime pruning synchronized Jatropha regrowth in summer and effectively stimulated growth after frost damage. Flowering started in February 2015 and peaked in April and May. Wide variations in flowering frequency were observed among different Jatropha accessions. Trees flowering in February and March produced fruit in May, but most trees only flowered in April and May and did not yield fruit because of cold snaps. These observations suggested that harvesting seed before wintertime is the key to improve Jatropha production in the Botswana climate. This study highlighted the importance of inducing early flowering by developing new agricultural managements. These may include frost cover and sun shades to prevent stress-induced damage, canopy control by pruning, optimization of fertilization practice, and/or introduction of superior Jatropha varieties.     

Analysis of long-term changes in the dates of seasonal phenomena in plants and insects of the Il’men Reserve as related to climatic factors

The results of monitoring the dates of the onset of flowering and leaf budding in eight herbaceous and woody plant species and the first appearance of three insect species in the Il’men Reserve (1972–2005) were processed by means of regression and correlation analyses. No significant changes in test parameters were revealed in the majority of these species. Only two early spring plants, coltsfoot (Tussilago farfara L.) and goat willow (Salix caprea L.), showed a weak tendency toward earlier flowering in the 1980s and 1990s. This is explained primarily by the absence of any significant trends in spring and summer air temperatures in the study region over the observation period. On the other hand, interannual fluctuations in the dates of plant flowering and insect appearance were well manifested not only in early spring but also in late-spring species. These fluctuations proved to depend largely on spring temperatures: in years with early and warm springs, flowering and leaf budding in plants and the appearance of first individuals in insects were recorded on significantly earlier dates.     

Determination of Au(III) and Pd(II) ions by flame atomic absorption spectrometry in some environmental samples after solid phase extraction

A simple and sensitive solid phase extraction method was developed for simultaneous separation and preconcentration of gold and palladium ions with N-(4-methylphenyl)-2-{[(4-phenyl-5-pyridine-4-yl-4H-1,2,4-triazol-3-yl)thio]acetyl}hydrazine carbo thioamide complex on Amberlite XAD-1180 resin before their determination by flame atomic absorption spectrometry. Some analytical parameters such as HNO₃ concentration of the sample solution, amount of complexing agent, sample volume, eluent type and volume, effects of foreign ions and adsorption capacity of the resin were investigated for quantitative recovery of gold and palladium ions. The effects of some anions and cations were also examined. Under optimum conditions, the detection limits for gold and palladium ions were found to be 0.29 and 0.19 μg L^?1, respectively. The preconcentration factor for gold and palladium was 250. After being validated by standard addition and analysis of standard reference material, the procedure was successfully applied to the analysis of sea and stream water, anodic slime, gold ore, soil and electronic waste.