固相萃取技术预富集环境水样中邻苯二甲酸酯

使用Ｃ₁₈固相萃取柱，系统地研究了环境水样中邻苯二甲酸酯类化合物的固相萃取预富集方法，考虑影响回收率的４个主要因素，即水样流速、洗脱溶剂、洗脱溶剂用量及洗脱速率，利用正交试验进行萃取条件的优化．最后确定最佳萃取条件为：水样流速４ｍ ｌ·ｍ ｉｎ^-1，洗脱溶剂为乙酸乙酯、洗脱溶剂用量２ｍ ｌ，洗脱速率２ｍｌ·ｍ ｉｎ^-1．并探讨了其它影响萃取效果的因素，除邻苯二甲酸二辛酯（ＤＥＨＰ）外，邻苯二甲酸二甲酯（ＤＭＰ）、邻苯二甲酸二乙酯（ＤＥＰ）、邻苯二甲酸二丁酯（ＤＢＰ）的固相萃取回收率在９６．５％ ～１２０％ 范围内，相应化合物的液－液萃取回收率为９２．９％ ～１２０％ ． 表明固相萃取，在环境水样中的邻苯二甲酸酯类化合物分离富集方面可以取代液－液萃取． 同时，进行了固相萃取柱在不同条件下的贮存实验．     

Al_2O_3负载Pd-Cu催化剂催化1,2-二氯乙烷加氢脱氯性能

采用共浸渍法制备了一系列Al2O3负载金属Pd、Cu催化剂.通过元素分析（ICP）、氮气吸脱附（BET）、X射线粉末衍射（XRD）、透射电镜（TEM）等技术对催化剂进行了表征,并以1,2-二氯乙烷气相加氢脱氯为探针反应,考察了Pd-Cu/Al2O3催化剂的钯铜比、反应温度、反应时间等因素对催化活性以及反应产物乙烯选择性的影响.结果发现,提高Cu负载量可在催化剂中形成Pd-Cu合金,并促进催化剂对乙烯的选择性.此外,当温度为250℃,Pd、Cu负载量分别为0.78%和1.9%时的Pd-Cu/Al2O3催化剂对1,2-二氯乙烷的催化加氢脱氯效果最佳,最终产物乙烯的选择性可达到80%以上.     

Three-dimensional visualization and quantification of non-aqueous phase liquid volumes in natural porous media using a medical X-ray Computed Tomography scanner

This study demonstrates the capabilities of a typical medical X-ray Computed Tomography (CT) scanner to non-destructively quantify non-aqueous phase liquid (NAPL) volumes, saturation levels, and three-dimensional spatial distributions in packed soil columns. Columns packed with homogeneous sand, heterogeneous sand, or natural soil, were saturated with water and injected with known quantities of gasoline or tetrachloroethene and scanned. A methodology based on image subtraction was implemented for computing soil porosity and NAPL volumes in each 0.35 mm x 0.35 mm x 1 mm voxel of the columns. Elimination of sample positioning errors and instrument drift artifacts was essential for obtaining reliable estimates of above parameters. The CT data-derived total NAPL volume was in agreement with the measured NAPL volumes injected into the columns. CT data-derived NAPL volume is subject to a 2.6% error for PCE and a 15.5% error for gasoline, at average NAPL saturations as low as 5%, and is mainly due to instrument noise. Non-uniform distributions of NAPL due to preferential flow, and accumulation of NAPL above finer-grained layers could be observed from the data on 3-D distributions of NAPL volume fractions.     

超高效液相色谱串联质谱法测定水体中17种抗生素

建立了一种超高效液相色谱串联质谱法同时测定饮用水源中17种超痕量水平抗生素的分析方法。采用Oasis HLB柱对500 mL pH=5含目标物的水样进行富集,干燥15 min后,用5%氨水甲醇洗脱,氮吹后定容至1 mL。用C₁₈柱吸附目标物,并用0.1%甲酸水和甲醇对目标物进行分离,采用正离子电喷雾电离模式在多反应监测通道中对目标物同时进行分析。该方法检出限为0.07~0.78 ng/L,超痕量水平下回收率范围为75.8%~108%。该方法灵敏度高,精密度为1.8%~15.0%,适用于同时测定饮用水源等水体中的抗生素。     

松花江水中13种内分泌干扰物的初步调查

用固相萃取(SPE)/高效液相色谱法(HPLC)同时测定了松花江水中的13种典型内分泌干扰物(EDCs).结果表明,哈尔滨段江水中雌三醇(E3)、雌二醇(E2)、雌酮(E1)、乙炔雌醇(EE2)及乙烯雌酚(DES)5种雌激素物质的浓度普遍较高.最高可达66 ng·L-1;酞酸二甲酯(DMP)、酞酸二乙酯(DEP)、酞酸二正丁酯(DnBP)及酞酸二(2-乙基己基)酯(DEHP)4种酞酸酯丰度最大,其中DnBP浓度最高可达330μg·L-1;4-正壬基酚(4-n-NP),带支链的对壬基酚(NP)及4-叔-辛基酚(4-t-OP)3种烷基酚的浓度范围为25-1261 ng·L-1;双酚A(BPA)浓度变化较小,保持在20-50 ng·L-1之间.经与相关报道比较,初步认为松花江水中雌激素类物质及酞酸酯污染较为严重,应当引起有关部门的警惕.     

反相高效液相色谱法测定污水中壬基酚聚氧乙烯醚总量

建立了固相萃取一反相液相色谱一荧光检测法分析污水中壬基酚聚氧乙烯醚总量的方法.固相萃取采用Wa-ters Oasis HLB固相萃取柱(30 μg×60 mg×3 mL),6 mL二氯甲烷/甲醇(90/10,V/V)混合溶剂洗脱,洗脱液用氮吹仪浓缩至1 mL,回收率为99.68%.采用ZORBAX Eclipse XDBC-18(4.6 mm×150 mm,5 μm)反相色谱柱,甲醇/水为流动相,流速1.0 mL/min,以每分钟增加2.5%的梯度陡度进行洗脱,流动相中甲醇比例由70%增加到100%,柱温23℃,进样量15μL.荧光检测器的激发波长230 nm,发射波长313 nm.采用外标法定量.该方法的空白加标和污水样品加标回收率均在90%以上,标准偏差小于10%,定量下限为0.97～1.90 μg/L.利用该方法分别对污水处理厂进水水样、二级处理出水水样、再生水水样进行了测定,测定结果的准确度和精密度满足痕量分析的要求.     

2,4-二硝基苯肼固相吸附/高效液相色谱法测定车内空气中醛酮类物质

建立了2,4-二硝基苯肼固相吸附／高效液相色谱同时测定车内空气中4种醛酮类物质的方法,研究了固相吸附采样和前处理方法,优化了试验条件。4种醛酮类物质在一定质量范围内工作曲线线性良好,甲醛、乙醛、丙烯醛、丙酮的检出限分别为0．075μg／m^3、0．207μg／m^3、0．715μg／m^3、0．159μg／m^3（按采样体积12L计）,实际样品测定的RSD为7.5％-9．7％。     

Experimental investigations on a forced convection solar air heater using packed bed absorber plates with phase change materials

In this work, the performance of a forced convection solar air heater was evaluated using using three packed bed absorber plate configurations and compared with flat absorber plate. The phase change material (paraffin wax) was packed in the pin-fin, trianglular and circular absorber plate configurations. The performance parameters such as, outlet air temperature, thermo-hydraulic efficiency, exergy efficiency and pressure drop were predicted and compared. The results showed that the packed bed absorber plate configurations using paraffin wax have higher outler air temperature in the range of 2–5°C with 3–40% higher thermo-hydraulic efficiency and 2–20% higher exergy efficiency when compared to flat absorber plate. However, the packed bed absorver plates have higher pressure drop when compared to flat absorber plate.     

Influence of the elastic behaviour of liquids on transient flow from pressurised containments

Release of liquids from vessels and pipelines is a very important scenario in consequence assessment. When the operating pressure is significant, its evolution and the corresponding discharge rate are affected by the elastic behaviour of the liquid. Bulk modulus is the key-driver of the related fluid-dynamics and is expected to govern the elastic-to-atmospheric pressure transition. Despite the well known physical background, the availability of release models relevant to the elastic phase is rather poor, compared to those relevant to vapours, gases and atmospheric liquids. On the other hand, if the operating pressure is high, release times and dynamics are expected to be strongly affected by the elastic behaviour and prediction of release time and flow rate is fundamental. This article carries outs a general analysis of the elastic behaviour of liquids, including water and hydrocarbons. Lumped (vessel-type) and distributed (pipeline) parameters systems have been modelled with the aim to characterize the pressure evolution during the elastic phase and to evaluate the significance of the associated duration. The findings have shown that, depending on pressure and geometric features, the importance of the elastic phase is high and that the availability of reliable and relatively simple models could be beneficial in consequence assessment. The approach is strictly valid for non-boiling liquid, but accounting for vaporisation of flashing or boiling liquids such as LPG and LNG would not imply significant complications.     

上海市污水二期干线排水风险评估及安全保障

上海市污水二期干线是上海市一条重要的排污干线,其安全运行对保障市区的排水安全具有重要的意义。通过建立污水二期干线管网系统的数学水力集成模型,对污水二期干线的水力状态进行模拟,预测在超强暴雨条件下污水二期干线的排水风险,提出污水二期干线的排水安全保障方案,为上海市区的防洪保安奠定基础。