活性污泥对四环素的吸附性能研究

通过批量平衡法研究了四环素在活性污泥上的吸附行为.结果表明,污泥混合液浓度和四环素初始浓度对吸附平衡时间、污泥吸附量和污泥吸附率均有较大影响.伪二级反应动力学模型较伪一级反应动力学模型更符合本吸附实验.在10、25℃条件下,四环素在活性污泥上的吸附行为较符合Langmuir模型,最大吸附量分别是31.14、70.95 mg.g-1;在40℃下,符合Henry模型.应用D-R模型判定吸附类型,10℃(平均吸附能为9.13 kJ.mol-1)下,化学吸附占主导;40℃(平均吸附能为7.07 kJ.mol-1)下,物理吸附占主导.温度升高,污泥对四环素的吸附能力增大.离子交换是四环素在活性污泥上吸附的一种机制.四环素的初始浓度为5、10、20 mg.L-1,钠离子浓度由0 mol.L-1增加到0.1 mol.L-1时,吸附量分别下降15.32%、15.00%、20.12%.当pH在5～10之间时,pH为6的条件下污泥对四环素的吸附量最大.     

Sewage sludge disintegration by high-pressure homogenization: A sludge disintegration model

High-pressure homogenization (HPH) technology was applied as a pretreatment to disintegrate sewage sludge. The effects of homogenization pressure, homogenization cycle number, and total solid content on sludge disintegration were investigated. The sludge disintegration degree (DDCOD), protein concentration, and polysaccharide concentration increased with the increase of homogenization pressure and homogenization cycle number, and decreased with the increase of sludge total solid (TS) content. The maximum DDCOD of 43.94% was achieved at 80 MPa with four homogenization cycles for a 9.58 g/L TS sludge sample. A HPH sludge disintegration model of DD_COD= kN^aP^b was established by multivariable linear regression to quantify the effects of homogenization parameters. The homogenization cycle exponent a and homogenization pressure exponent b were 0.4763 and 0.7324 respectively, showing that the effect of homogenization pressure (P) was more significant than that of homogenization cycle number (N). The value of the rate constant k decreased with the increase of sludge total solid content. The specific energy consumption increased with the increment of sludge disintegration efficiency. Lower specific energy consumption was required for higher total solid content sludge.     

Responses of protists with different feeding habits to the changes of activated sludge conditions: A study based on biomass data

Changes of protists, which were categorized into different functional groups primarily according to their feeding habits, in two full-scale municipal wastewater treatment systems experiencing sludge bulking were investigated over a period of 14 months. Protist biomass represented 3.7% to 5.2% of total biomass on average under normal sludge conditions, and the percentage increased significantly (p < 0.05) under sludge bulking conditions. The biomass of Chilodonella spp., capable of eating filamentous bacteria, tended to decrease in both systems when sludge bulking occurred, showing that the abnormal growth of filamentous bacteria did not lead to a biomass bloom of this group of protists. On the other hand, the bactivorous protists represented more than 96% of total protist biomass, and the biomass of this group, particularly the attached ciliates, increased significantly (p < 0.05) when sludge bulking occurred. The significant increase of the attached ciliates may have possibly facilitated the growth of filamentous bacteria through selectively preying on non-filamentous bacteria and further exacerbated sludge bulking. The redundancy analysis and correlation analysis results showed that the biomass changes of the attached ciliates were primarily related to the sludge volume index and to some extent related to five-day biochemical oxygen demand loading and hydraulic retention time.     

Pb2+对城市污水处理厂污泥中苏云金芽孢杆菌发酵的影响

以城市污水处理厂污泥为培养基,研究了添加Pb2+对Bt(Bacillus thuringiensis,苏云金芽孢杆菌)生长和晶体蛋白合成的影响,同时分析了Bt发酵过程中有效态Pb含量(以ρ计)的变化,并采用FTIR(傅立叶红外光谱)和XPS(X射线光电子能谱),初步探讨了Pb2+在Bt表面的作用机制.结果表明:污泥培养基在支持Bt生长代谢和降低重金属有效态含量方面均优于商用培养基,当初始ρ(Pb2+)高达400 mg/L时,与未添加Pb2+相比,污泥培养基中Bt活菌数与晶体蛋白产量约分别下降48%和54%,而商用培养基中约分别下降82%和75%,证实了污泥作为Bt发酵培养基的可行性;Bt对Pb2+有较好的耐受性,当ρ(有效态Pb)在80 mg/L以下时,Bt生长代谢不会受到显著影响.光谱学分析表明,Bt对Pb2+有少量吸附,从而降低Bt发酵过程中Pb的生物有效性,吸附位点主要为羟基,部分C O和S O也参与了吸附反应.     

MBR活性污泥培养驯化过程中生物多样性研究

以MBR反应器启动调试阶段的活性污泥为主要研究对象,系统考察了传统活性污泥法(Conventional activated sludge,CAS)污泥接种至MBR反应器内污泥培养驯化过程中生物多样性情况及微生物群落结构的演变规律.同时,在传统污水污泥检测指标的基础上,对各阶段污泥中总细菌基因组DNA进行提取,应用PCR-DGGE分子生物学技术获得了相应的凝胶电泳图谱并进一步分析了菌群间的相似性.结果表明,以CAS污泥为接种污泥在MBR反应器内培养驯化过程中微生物的多样性变化突出,细菌群落结构演替明显,不同阶段菌群间的相似性说明了各阶段菌群的演变关系:污泥培养驯化是一个逐步有序的过程,微生物随反应器内不同时期及环境的变化而调整,逐渐演变成适应MBR工艺的群落结构.     

污泥活性炭理化性质表征及吸附抗生素效果研究

文章以北京方庄污水处理厂的浓缩和脱水污泥为原料,采用ZnCl2活化法分别制备污泥活性炭。对制得的污泥活性炭进行表征,并将其应用于加替沙星废水的处理。研究2种污泥活性炭吸附反应的吸附时间、吸附剂投加量、pH值、初始浓度4个因子对吸附量的影响,设计正交实验。正交实验结果表明:2种污泥活性炭受到4个因子影响程度相当,表现出明显的相似性,但短期吸附时,脱水污泥表现出更好的吸附性能。初始浓度对吸附量的影响最大,获得最大吸附量的条件组合为:初始浓度200 mg/L,投加量0.05 g,pH=9,t=2 h。浓缩和脱水污泥活性炭的最大吸附量分别可达34.541 mg/g和34.925 mg/g,表明2种污泥活性炭对加替沙星均有良好的吸附效果。污泥活性炭作为一种废水吸附剂,是废水处理的一种新途径。     

硫酸盐还原颗粒污泥对Cr的吸附机理解析

以硫酸盐还原颗粒污泥作为研究对象,进行Cr的吸附容量研究及吸附等温线拟合,测定颗粒污泥中的硫化物含量、对比实验前后颗粒污泥的表面形态和微生物组成并采用傅里叶红外变换光谱(FTIR)分析颗粒污泥的表面基团。结果表明,颗粒污泥对Cr的吸附容量为6.84 mg/g,吸附过程可用Langmuir吸附等温式描述。颗粒污泥中硫化物含量达9.868 mg/g(湿重),对应每克颗粒污泥对Cr的最大吸附量可达10.69 mg;颗粒污泥表面生长大量的微生物,以杆菌为主,颗粒污泥表面丰富的微孔结构及微生物所分泌的胞外物均可有效吸附溶液中的Cr;FTIR分析结果显示,颗粒污泥中包含大量C=O、C-N及-S等基团,这些基团均可通过与C(rⅥ)或C(rⅢ)之间的静电吸附作用吸附溶液中的Cr。研究表明化学与生物吸附作用在硫酸盐还原颗粒污泥吸附溶液中的Cr过程中起到了重要的作用。     

污泥基活性炭的制备、表征及其应用

以城市生活污水厂脱水车间污泥为原料,采用化学活化法(ZnCl2为活化剂)在活化剂浓度为45%、活化温度为600℃、浸渍温度为45℃、活化时间为50min条件下制备污泥基活性炭。对污泥基活性炭进行了孔结构、扫描电镜(SEM)、红外光谱(FTIR)、XRD等表征分析。结果表明:该条件下制备出的污泥基活性炭碘吸附值为427.51mg/g,比表面积为329.48m2/g,大孔、中孔、微孔容积分别为0.19,0.12,0.15cm3/g。平均孔径为3.953nm。将其应用于生活污水处理,考察了污泥基活性炭投加量、pH、吸附时间对其吸附性能的影响。     

污水处理厂不同工艺的污泥脱水效能分析及其影响因素研究

污泥脱水是污泥减量的主要手段,直接影响到后续污泥处理处置.本研究以北京某大型污水处理厂A2/O工艺和A2/O-MBR工艺污泥脱水为对象,基于2013年全年的运行数据,分析不同工艺的污泥脱水效果、絮凝剂投配率、污泥脱水电耗和污泥脱水成本,并通过冗余分析(RDA)研究了不同污水处理工艺污泥脱水性能的影响因素.结果表明,污泥脱水性能和絮凝剂投配率均呈现季节性变化特征,冬季污泥较难脱水,絮凝剂消耗大.A2/O-MBR工艺的脱水污泥含水率年均值为(81.92±1.64)%,A2/O工艺为(82.56±1.35)%,污泥脱水絮凝剂消耗(以DS计,下同)分别为(8.70±7.25)kg·t-1和(7.42±2.96)kg·t-1,电耗(以DS计,下同)分别为331.82 k W·h·t-1和121.57 k W·h·t-1.A2/O-MBR工艺的污泥脱水絮凝剂成本(以DS计,下同)为204.76元·t-1,用电成本为231.61元·t-1;A2/O工艺的污泥脱水絮凝剂成本为175.00元·t-1,用电成本为84.86元·t-1.RDA分析表明,水温等季节性因素引起污泥有机质变化是影响污泥脱水性能的关键因素之一,此外,污泥龄也与污泥脱水性能有一定相关性.     

活化过硫酸盐对市政污泥调理效果的影响

常规污泥脱水技术只能将市政污泥含水率降到80%左右,难以满足日益严格的污泥处理处置要求.活化过硫酸盐产生硫酸根自由基SO4·-具有强氧化性,可用于破坏污泥的絮体结构.本研究利用Fe2+活化过硫酸钠(SPS)的方法进行污泥调理,以到达改善污泥的脱水性能的目的.结果表明,当Fe2+与S2O2-8投加量(以绝干污泥计)分别为25.88 mg·g-1、80 mg·g-1(Fe2+与S2O2-8摩尔比为1.1∶1)时,污泥毛细吸水时间CST和污泥比阻SRF降低率最大,滤液中蛋白质和多糖浓度达到最大.进一步的研究表明,污泥Zeta电位值由负向正变化,颗粒比表面积增大,絮体由密集的团状变成结构松散的层状结构,污泥脱水性能提高.