Determination and discussion hydraulic retention time in membrane bioreactor system

Based on the microorganism kinetic model, the formula for computing hydraulic retention time in a membrane bioreactor system (MBR) is derived. With considering HRT as an evaluation index a combinational approach was used to discuss factors which have an effect on MBR. As a result, the influencing factors were listed in order from strength to weakness as: maximum specific removal rate K, saturation constant Ks, maintenance coefficient m, maximum specific growth rate ,ua and observed yield coefficient Yobs. Moreover, the formula was simplified, whose parameters were experimentally determined in petrochemical wastewater treatment. The simplified formula is θ= 1.1( 1/β -1)(Kｓ S)/KXo , for oetroehemical wastewater treatment K and Ko eaualed 0.185 and 154.2, resoectively.     

Preparation and coagulation efficiency of polyaluminium ferric silicate chloride composite coagulant from wastewater of high-purity graphite production

The aim of the present work was to produce a polyaluminium ferric silicate chloride (PAFSiC) coagulant from acidic and alkaline wastewater of purifying graphite by roasting, and subsequently to evaluate coagulation efficiency of the reagent by treating surface water from the Yellow River as well as municipal wastewater in comparison with the conventional coagulant polyaluminium chloride (PAC). The PAFSiC coagulant was prepared by co-polymerization. The effects of (Al+Fe)/Si molar ratio, OH/(Al+Fe) molar ratio (i.e., value), coagulant dosage and pH value of test suspension on the coagulation behavior of FAFSiC and the stability of the PAFSiC were also examined. Results showed that PAFSiC performed more efficiently than PAC in removing turbidity, chemical oxygen demand (COD), and total phosphate (TP). The PAFSiC with a value of 2.0 and (Al+Fe)/Si ratio of 5 (PAFSiC 2.0/5) showed excellent coagulation effect for both turbidity and COD, while PAFSiC 1.0/5 was the best for TP. The optimum coagulation pH range of PAFSiC 2.0/5 was 5.0–9.0, slightly wider than that of PAC (6.0–8.0). The process can be easily incorporated into high-purity graphite production plants, thereby reducing wastewater pollution and producing a valuable coagulant.     

红树林系统处理牲畜废水营养盐的研究

在2种盐度条件下（淡水与盐度30的人工海水）通过温室盆栽系统对比研究了2种主红树植物木榄和秋茄对牲畜废水的处理效应。牲畜废水的加入使植物体P含量增加1－4倍，N含量增加0.04-1.30倍。淡水条件 下秋茄和木榄系统N的处理效率分别为84.3%和95.5%，海水条件 下则为92.7%和98.0%，淡水条件下秋茄和木榄系统P的处理效率分别为79.2%和91.8%，海水条件下则为88.0%和97.8%，盐度对秋茄植物体N的去除无显著效应。2种植物体对P的处理效率为4％，远比N的处理效率低，废水来源的营养 盐大多被土壤去除。     

厌氧流化床反应器处理含硫废水毒性的实验

采用多孔聚合物载体固定化微生物在厌氧流化床（AFB）反应器中处理含硫废水,研究反应器抗硫化物（S^2－）毒性抑制和抗硫酸盐毒性抑制的能力;探索解除 S^2－毒性的方法．研究表明,当进料基质 COD浓度为 5000mg/L,HRT为5.2－5.4h,S^2－＜200mg/L时,反应器去除 COD效果不受影响,S^2－350mg/L时,厌氧消化受到明显抑制,反应器可容忍530mg/L S^2－浓度而未造成消化系统的破坏;SO₄^2－浓度高达3521mg/L,COD去除率仍可达77％－80％,但SO₄^2－去除率明显下降;当COD/SO₄^2－的比值大于1.45时,硫酸盐还原菌和产甲烷菌的生长未受到明显抑制,此时容积负荷为22－24kgCOD/（m³>·d）,COD去除率为80％,SO₄^2－去除率为58.8％;向反应器投加适量FeCl₂可很好地解除S^2－的抑制．     

多金属氧酸盐电催化降解染料废水的研究

采用IR和XRD等手段对磷钼酸(PMo12)和3,3',5,5'-四甲基联苯胺(TMB)形成的电荷转移配合物(TMB)3PMo12进行表征,结果表明配合物中的杂多阴离子仍保留着Keggin结构.将配合物负载于γ-Al2O3上制备(TMB)3PMo12/γ-Al2O3负载型催化剂填充于电化学反应器中,考察电催化氧化体系降解酸性大红3R染料废水的效果.研究表明,(TMB)3PMo12/γ-Al2O3催化剂对酸性大红3R废水显示了良好的电催化活性,催化剂填充量为50g,负载量为0.6%时,在pH值为4,槽电压15.0V,曝气量0.14m3/h,极板间距3.0cm反应条件下,60min后,色度去除率达到79.7%,去除效果较传统二维平板和三维电解槽更高.     

SBR处理模拟氯苯废水

在SBR中利用光合细菌球形红细菌污泥颗粒进行模拟氯苯废水处理的初步研究,结果表明,采用球形红细菌污泥颗粒处理模拟氯苯废水的SBR系统是可行的,其降解氯苯过程符合Monod一级反应动力学方程。当进水氯苯浓度在125～187.5 mg/L变化时,处理效率都能稳定在90.5%～95.6%之间;其最佳工艺条件为反应时间6 h、DO 4.75～5.0 mg/L、沉淀时间1.5 h、污泥颗粒浓度4 000～6 000 mg/L。在污泥颗粒浓度4 000 mg/L、DO 5.0 mg/L、反应时间6 h的最佳条件下,当进水COD为748.1 mg/L、氯苯浓度100 mg/L时,COD的去除率达90.9%,处理后出水COD满足国家一级排放标准要求。     

Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

电感耦合等离子体发射光谱法测定石化废水中的重金属

建立了硝酸加热消解后采用电感耦合等离子体发射光谱(ICP-OES)测定石化废水中重金属(As,Cd,Cr,Cu,Zn,Pb,Mn)的方法,优化了仪器工作参数,得到了线性回归方程,并对该方法进行了评价。优化后的仪器工作参数为射频功率1 150 W、雾化器流量0.70 L/min、辅助气流量0.50 L/min。各重金属元素回归方程的相关系数均在0.999 9以上,检出限为0.000 18~0.007 00 mg/L,相对标准偏差为0.1%~2.0%,加标回收率为96.3%~102.2%。该方法具有线性关系好、检出限低、精密度和准确度高、分析速度快等优点。     

土壤-纳滤系统处理再生水补充地下水的研究

为充分保障再生水回灌地下时的水质安全、提供高质量地下水资源,在土壤处理系统中嵌入纳滤技术强化对再生水的处理效果,并初步探讨土壤系统作为前处理对纳滤膜污染的控制机理.结果表明,未采用臭氧氧化预处理前,土壤处理对再生水DOC和UV254的平均去除率分别为22%和20%.臭氧氧化对UV254的平均去除率为51%,并将土壤对D...     

电絮凝净化含聚污水影响因素研究

目的为保障油田正常安全生产,促进油田含聚污水的循环利用。方法采用电絮凝技术单因素研究方法开展净化含聚污水的静态实验研究,探讨外加电流密度、极板间距、初始pH及聚合物浓度等因素对净化效果的影响规律。结果当初始pH为7.0,电流密度为4.0 m A/m2,极板间距为1.0 cm,电解16 min时,综合处理效果最佳。此时,含油量与浊度去除率分别为98.85%,99.93%,处理每克油平均消耗为0.0494 g的Al,处理每立方米含聚污水的能耗为0.2895 k Wh。污水中的聚合物浓度越小,净化效果越好。结论中性处理,极板间距为1.0 cm,外加电流密度为4.0 m A/m2,通电16 min是最佳处理条件。