石化企业中间罐区VOCs治理工艺选择与流程优化

石化企业中间罐区VOCs排放量较大,多采用吸收、冷凝、膜分离及其组合工艺进行处理。本文采用AspenPlus软件分别对高、中、低浓度中间罐区VOCs废气应用上述3种工艺及其工艺组合的处理效果进行模拟计算。结果表明:中间罐区的VOCs经过不同组合的二级处理后,尾气VOCs质量浓度约为9～50 g/m~3,后续仍需采用深度处理工艺以满足新的国家及地方污染物排放标准要求;同时,对比3种工艺能耗情况,冷凝法最低,膜分离法次之,吸收法最高,约为冷凝法能耗的5～10倍。以上模拟计算结果与实际工况数据基本符合,证明采用Aspen Plus软件进行石化企业中间罐区VOCs治理工艺选择与流程优化是可行的,具有一定的参考价值。     

有机溶剂回收技术的研究

本文对有机溶剂的回收方法，如吸附法、吸收法、冷凝法和膜分离法等的研究进展与应用进行了综述。其中，吸附法在工业上的应用最为广泛，本文着重介绍了吸附法的工艺以及吸附剂的研究。而膜分离法作为最有发展前景的一种回收方法，主要问题为提高膜的通量和选择性。     

Why biota still accumulate high levels of PCB after removal of PCB contaminated sediments in a Norwegian fjord

Accumulation of polychlorinated biphenyls (PCBs) in blue mussels (Mytilus edulis) and semipermeable membrane devices (SPMDs) was still high after the removal of PCB contaminated sediments from a Norwegian fjord by dredging. The accumulation of low chlorinated PCB congeners with a low octanol water-partitioning coefficient (K_ow) in blue mussels and SPMDs was higher than for the highly chlorinated congeners with a high K_ow. The accumulation of low chlorinated congeners was also higher in a lightly contaminated area compared to a highly contaminated area. That dredging the contaminated sediments was unsuccessful in lowering PCB levels in the biota may be for the following reasons: (1) Due to the low solubility of PCBs in the water it is possible that a decrease in the sediment concentration of PCB would leave the water concentrations of PCB unchanged. (2) Removal of the fine organic sediments may also play an important role, since a seabed with coarse inorganic material has a lesser ability to bind PCB. (3) The dredging may whirl up fine contaminated particles that eventually settles on the seabed producing a thin contaminated sediment layer that determine the water concentration. (4) Bioaccumulation in blue mussels and in the SPMDs occurs mostly from PCB dissolved in the water column. Since the water concentration of PCB is unchanged by the dredging, the accumulation in SPMDs and mussels is the same as before dredging. Further monitoring need to be carried out to report the long-term effect of the dredging.     

水中污染物对阳离子交换膜分离去除Cu2+的影响

基于Donnan dialysis原理,在无外加电压作用下采用阳离子交换膜分离去除原水中的Cu2+,研究原水中可能出现的无机颗粒物,有机物质,EDTA酸、氨水、Fe3+、表面活性剂等对阳离子交换膜分离去除Cu2+效果的影响.研究表明:原水中添加二氧化硅、腐殖酸、EDTA酸、氨水、Fe3+、表面活性剂等物质,在长时间运行后均会对离子交换膜去除Cu2+有不同程度的影响;二氧化硅和非离子表面活性剂等污染物不会和膜及Cu2+发生物理化学反应,对膜去除Cu2+效果影响较小,相比空白样,Cu2+去除率下降约4%;氨水、阴离子表面活性剂等会导致Cu2+发生沉淀反应,腐殖酸会吸附Cu2+,使原水中游离态Cu2+浓度显著降低约50%;EDTA酸、氨水、阴离子表面活性剂等会与Cu2+形成络合物,对去除Cu2+有严重影响,相比空白样, Cu2+去除率分别下降约100%(EDTA酸)、78%(氨水)、56%(阴离子表面活性剂);阳离子表面活性剂存在时,其会大量占据膜内空间,Cu2+基本无去除;Fe3+在弱酸性或中性水中会水解生成氢氧化铁胶体,对去除Cu2+有一定影响,相比空白样, Cu2+去除率下降约12%.     

环境因素对菹草根和叶细胞质膜Ca2+-ATPase活性的影响

通过改变溶液温度、pH值、ATP浓度、钙浓度和培养液的钙浓度等条件,研究了菹草根和叶细胞质膜Ca2+-ATPase的活性的变化.结果表明,根细胞质膜Ca2+-ATPase的活性在pH 6.0时最高,其最适反应温度为40℃;叶细胞质膜Ca2+-ATPase在一个较宽的pH范围内具有高活性,最适反应温度为45℃;溶液中ATP浓度分别为3mmol/L和4mmol/L时菹草根和叶细胞质膜Ca2+-ATPase活性最大;无论是菹草根还是叶细胞质膜Ca2+-ATPase活性,在溶液钙浓度为10-4mol/L时都最高.在营养液中添加不同CaCl2浓度培养菹草,其根和叶细胞质膜Ca2+-ATPase活性表现出差异,根细胞质膜Ca2+-ATPase活性比叶细胞质膜Ca2+-ATPase活性高,且随营养液中钙浓度的增加,这种差异加大;当营养液中钙浓度在10mg/L(2.5×10-4 mol/L)以下时,Ca2+-ATPase活性逐渐上升,营养液中钙浓度由10mg/L增加到15mg/L,Ca2+-ATPase活性陡然下降,这与溶液钙浓度对Ca2+-ATPase活性的影响相呼应.     

太湖原水中膜污染物质的确定与表征

采用混凝沉淀和浸没式微滤膜联用技术处理太湖原水,考察组合工艺中的有机物亲疏水性和分子量分布变化,并分析化学清洗水的有机物组分,以期确定造成膜污染的主要物质成分.结果表明,混凝预处理可有效去除大分子的亲水性有机物,这类有机物仅能导致可逆污染,而中等和小分子的有机物会导致不可逆污染.此外,三维荧光光谱表明与膜污染关系最密切的2个区域为:λex=230nm/λem=330~350nm (区域Ⅰ)和λex=280nm/λem=300~350nm (区域Ⅳ),其对应的胞外蛋白质类有机物和溶解性微生物产物(SMP)是造成微滤膜不可逆污染的主要物质.     

陶瓷膜处理啤酒洗瓶废碱液的膜污染和清洗再生

研究了陶瓷膜过滤啤酒洗瓶废碱液膜污染机理,提出了相应的清洗再生方案。对比研究了硝酸、盐酸、次氯酸钠、三聚磷酸钠4种清洗剂单独使用和复合使用的清洗再生效果。试验表明:0.20%硝酸+0.55%次氯酸钠+0.15%三聚磷酸钠复合清洗再生陶瓷膜,膜通量恢复率在85%以上。陶瓷膜连续运行两个月,清洗再生效果稳定,具有工程实用价值。     

一体式MBR污泥特性及对其过滤性能的影响

研究了一体式MBR长期不排泥运行的污泥特性变化,考察了水力停留时间、曝气量等因素对污泥增长特性、污泥颗粒粒径分布及膜过滤性能的影响,并探讨了这些因素之间的关系。结果表明:水力停留时间越短,MLSS与MLVSS增加越快,膜污染加速,膜过滤阻力增加越快,但MBR中污泥浓度的增长、变化对出水COD的影响不明显;污泥平均粒径随SRT的延长而减小,实验结束污泥粒径最小值为0.6μm大于实验用膜的孔径0.2μm,表明混合液中的微细颗粒污泥未对膜通量的下降起决定性作用,膜表面污泥的沉积对膜通量影响更大一些,增加曝气强度可以明显改善MBR的过滤性能。     

化学沉淀-微滤-络合-超滤处理高浓度含镍废水

在pH=9下,镍离子浓度为5562.71mg/L的镍废水经充分沉淀后,以0.5μm孔径陶瓷膜微滤处理,发现浓缩时膜通量(J)先快速降低,经缓慢下降后,再较快降低,镍截留系数(R_Ni)接近1,当体积浓缩因子(VCF)从1增大到10时,截留液镍浓度(C_r)从5562.71mg/L浓缩至55507.76mg/L,渗透液镍浓度(C_p)为13.26mg/L.以陶瓷膜渗透液为料液,以聚乙烯亚胺为络合剂,考察聚合物与金属质量比(r_p/m)、pH值、温度和操作压力对恒容超滤R_Ni和J的影响,并研究超滤浓缩过程.结果表明,R_Ni随r_p/m或pH增大而增大,随温度升高而略下降,与操作压力无关;J随温度或操作压力增大而增大,随pH增大而增大至不变,r_p/m对J影响甚微.超滤浓缩时,控制r_p/m=7和pH=9,当VCF从1增大到30时,J仅下降9.76%,C_r从13.26mg/L增大至396.64mg/L,C_p约0.04mg/L,镍离子被浓缩,超滤渗透液可直接排放.     

Using crosslinked polyvinyl alcohol polymer membrane as a separator in the microbial fuel cell

Separator between anode and cathode is an essential part of the microbial fuel cell （MFC） and its property could significantly influence the system perfor- mance. In this study we used polyvinyl alcohol （PVA） polymer membrane crosslinked with sulfosuccinic acid （SSA） as a new separator for the MFC. The highest power density of 7594-4 mW-m-2 was obtained when MFC using the PVA membrane crosslinked with 15% of SSA due to its desirable proton conductivity （5.16 x 10-2 S.cml）. The power density significantly increased to 11064- 30 mW.m-2 with a separator-electrode-assembly config- uration, which was comparable with glass fiber （11704- 46 mW.m-2）. The coulombic efficiencies of the MFCs with crosslinked PVA membranes ranged from 36.3% to 45.7% at a fix external resistance of lO00f2. The crosslinked PVA membrane could be a promising alter- native to separator materials for constructing practical MFC system.