地下水PRB原位生物修复中一种释氧材料的改进技术及效果分析

释氧材料经济有效的释氧是地下水原位生物修复的关键因素。实验通过在释氧材料中加入膨润土、磷酸二氢钾和硫酸铵等,改进释氧材料的性能。柱实验结果显示,该释氧材料释氧速率缓慢,释氧时间长,可以使溶液中DO长期保持在5 mg/L以上;另外,释氧材料中添加的缓冲剂及天然含水层介质对pH值有较好的缓冲作用,可以使pH值达到后续生物修复的要求。     

Facilitating substance phase‐out through material information systems and improving environmental impacts in the recycling stage of a product

The amount of electrical and electronic products is increasing rapidly, and this inevitably leads to the generation of large quantities of waste from these goods. Some of the generated e‐waste ends up in regions with sub‐standard recycling systems and may be processed under poor conditions. During uncontrolled incineration, halogenated dioxins and furans can be generated from brominated and chlorinated compounds in the products. In order to reduce the health and environmental risks involved in the recycling stage of the life cycle of electronics, an effective design‐for‐environment process must be established during the product development phase. Knowledge of the chemical substances in the product is crucial to being able to make informed decisions. Through full knowledge of the material content of procured components, phase‐outs of unwanted substances, such as halogenated substances, can be performed in an effective manner. Therefore, information is the key to success in phasing‐out substances; facilitating compliance of legal provisions for manufacturers of electrical and electronic devices; and improving the environmental footprint of products as they reach the end of the life cycle. After an introduction to the challenges of electronics waste management, this paper describes supply chain information systems and how they are used to facilitate substance phase‐outs in the electronics industry. Sony Ericsson has been working with phase‐outs of unwanted substances since it was founded in 2001. Through the introduction of a material declaration system that keeps track of all substances in the components used in the company's products, Sony Ericsson has been able to replace unwanted substances to improve environmental impacts at the recycling stage of a product.     

基于冷阴极触发管振动试验夹具的设计

介绍了一种基于冷阴极触发管性能检测及振动试验所需的夹具,从夹具材料的选取、结构设计和刚度要求进行了设计,分析了该夹具在制造过程中存在的关键问题及解决方法,并在振动试验中加以验证。     

袋式除尘器在沥青混凝土搅拌设备上的应用

分析了沥青混凝土搅拌设备的构成以及生产沥青混凝土的工艺及烟尘特点;通过应用工程实例,指出袋式除尘器是沥青混凝土搅拌设备最理想的除尘系统之一。     

Localization of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene (TNT) in poplar and switchgrass plants using phosphor imager autoradiography

Phosphor imager autoradiography is a technique for rapid, sensitive analysis of the localization of xenobiotics in plant tissues. Use of this technique is relatively new to research in the field of plant science, and the potential for enhancing visualization and understanding of plant uptake and transport of xenobiotics remains largely untapped. Phosphor imager autoradiography is used to investigate the uptake and translocation of the explosives 1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene within Populus deltoides × nigra DN34 (poplar) and Panicum vigratum Alamo (switchgrass). In both plant types, TNT and/or TNT-metabolites remain predominantly in root tissues while RDX and/or RDX-metabolites are readily translocated to leaf tissues. Phosphor imager autoradiography is further investigated for use in semi-quantitative analysis of uptake of TNT by switchgrass.     

酸雨对建筑材料的影响及防治研究综述

综合分析了酸雨对建筑外墙的涂料、石材、混凝土等主要建筑构件的腐蚀原理,并提出了防治措施,来预防酸雨对建筑材料的侵害。     

利用高炉水淬渣制作多孔吸声材料的研究

为了促进高炉炼铁水淬渣的二次利用,研究了以高炉炼铁水淬渣为原料,以硅微粉或水泥为粘结剂,采用压制成型方法制作的多孔吸声材料的吸声性能及力学性能。结果表明:用颗粒状的高炉炼铁水淬渣制作的多孔吸声材料具有良好的吸声性能,其平均吸声系数可以达到0.70以上;材料的抗压强度可以达到3.0 MPa以上。     

多孔镁铝复合氧化物对水溶液中Cr（VI）的吸附性能

摘要以镁盐、铝盐、纯碱和烧碱为原料制备了一种多孔镁铝复合氧化物（P—Mg3.1AlO4.6）,其比表面积、平均孔径和总孔容分别为206．3m2／g、8．961nm和0．4208cm3／g。研究了这种多孑L材料对水溶液中cr（VI）的吸附性能,在25～45qC时,静态吸附量为82．32～141．7mg／g;当初始浓度100mg／L、流速5mL／min、床层高度10cm和pH=6时,半穿透时间、半穿透吸附量和饱和吸附量分别为406rain、49．28ing／g和51．30Ing／g;拟合参数及误差分析表明,cr（Ⅵ）在P—M敬。AIO4.6上的静态吸附过程符合Freundlich等温方程式和伪二级动力学方程,Yoon·Nelson模型能很好地预测cr（Ⅵ）在P—Mg3.1A104.6上的动态穿透曲线。     

废LCD面板有机材料水热资源化产乙酸

LCD面板主要由附着偏光片及液晶等有机材料的玻璃面板构成。有机材料的去除及资源化利用是废LCD面板处理的第一步。在水热条件下对废LCD面板进行了降解产酸研究。研究考察了反应温度、反应时间、氧化剂用量、水用量及pH值等对水热产乙酸产率及选择性的影响。通过正交实验确定了水热产乙酸的最佳操作条件：反应温度325℃,反应时间5min,氧化剂（30％H2O2）0．6mL,用水量2mL,近中性环境（pH6-6．5去离子水）。此条件下,乙酸产率及选择性分别为68．83％及70．56％。结果表明,以废LCD面板有机材料为原料,采用水热技术进行产乙酸反应,可实现其资源化再利用。     

工业废水中多金属离子的吸附净化

以含有Si、Al、Ca、C元素的矿物材料作为基质,经特定条件处理后造粒成型加工成轻质多孔Si-Al-Ca-C结构的吸附材料。研究了该吸附材料对工业废水中多种金属离子的吸附性能,探讨了影响吸附性能的因素。研究结果表明,在一定条件下,Si-Al-Ca-C吸附材料对工业废水中Al3+、Ca2+、Mn2+、Cu2+、Fe3+、Mg2+、As3+和Zn2+的净化率分别高达99.34%、99.82%、98.26%、98.16%、97.76%、97.01%、100%和89.09%。金属离子残留浓度分别为0.152、0.07、0.012、0.02、0.119、0.311、0和0.259 mg/L,均低于国家污水综合排放标准(GB8978-1996)一级标准。