化学混凝-SBR法处理肉禽屠宰废水的研究

针对肉禽屠宰废水的特点，采取了先混凝后生化的处理方法。在实验中确定了最佳混凝剂和最佳工艺条件。实验结果表明，采取此方法处理肉禽屠宰废水，其各项指标可达国家规定的排放标准。     

絮凝法分离谷氨酸菌体的研究

采用絮凝法对味精发酵生产过程中发酵液中的菌体进行研究，得到无机凝聚剂与高分子絮凝剂复合配比使用是发酵液去除菌体的有效办法。对复合用药除菌后的谷氨酸发酵液和原谷氨酸发酵液进行谷氨酸回收的比较，谷氨酸的回收率提高了8．8％。     

Starch, Poly(lactic acid), and Poly(vinyl alcohol) Blends

Research on biodegradable materials has been stimulated due to concern regarding the persistence of plastic wastes. Blending starch with poly(lactic acid) (PLA) is one of the most promising efforts because starch is an abundant and cheap biopolymer and PLA is biodegradable with good mechanical properties. Poly(vinyl alcohol) (PVOH) contains unhydrolytic residual groups of poly(vinyl acetate) and also has good compatibility with starch. It was added to a starch and PLA blend (50:50, w/w) to enhance compatibility and improve mechanical properties. PVOH (M_W 6,000) at 10%, 20%, 30%, 40%, 50% (by weight) based on the total weight of starch and PLA, and 30% PVOH at various molecular weights (M_W 6,000, 25,000, 78,000, and 125,000 dalton) were added to starch/PLA blends. PVOH interacted with starch. At proportions greater than 30%, PVOH form a continuous phase with starch. Tensile strength of the starch/PLA blends increased as PVOH concentration increased up to 40% and decreased as PVOH molecular weight increased. The increasing molecular weight of PVOH slightly affected water absorption, but increasing PVOH concentration to 40% or 50% increased water absorption. Effects of moisture content on the starch/PLA/PVOH blend also were explored. The blend containing gelatinized starch had higher tensile strength. However, gelatinized starch also resulted in increased water absorption.     

Mechanical Properties with the Functional Group of Additives for Starch/PVA Blend Film

This paper deals with the mechanical properties and degree of swelling (DS) of starch/PVA blend film with the functional groups i.e., hydroxyl and carboxyl group, of additives. Starch/PVA blend films were prepared by using the mixing process. Glycerol (GL) with 3 hydroxyl group, sorbitol (SO) with 6 hydroxyl group, succinic acid (SA) with 2 carboxyl group, malic acid (MA) with 1 hydroxyl and 2 carboxyl group, tartaric acid (TA) with 2 hydroxyl and 2 carboxyl group and citric acid (CA) with 1 hydroxyl and 3 carboxyl group were used as additives. The results of measured tensile strength (TS) and elongation (%E) verified that both hydroxyl and carboxyl group as a functional groups increased the flexibility and strength of the film. Values of DS for GL-added and SA-added films were low. However, DS values of the films added MA, TA or CA with both hydroxyl and carboxyl group were comparatively high. When the film was dried at low temperature, the properties of the films were evidently improved. The reason is probably because the hydrogen bonding was activated at low temperature.     

聚合硅酸硫酸铝铁的制备与应用

在n(Fe A1)／n(Si)为0．5～1．0、n(Al)／n(Fe)为2．5～3．0、SiO2质量分数为2．3％、硅酸钠溶液的活化pH为5．5、硅酸钠溶液的活化时间为12min或SiO2的质量分数为2．0％、硅酸钠溶液的活化pH为6．0、硅酸钠溶液的活化时间为3min的条件下，制备出的聚合硅酸硫酸铝铁对废水的除浊效果最佳，除浊率大于98％。     

含疏松缺陷的ZL205A合金力学性能研究

目的获取含疏松缺陷ZL205A材料主要力学性能参数的变化规律及力学行为。方法通过单轴拉伸实验测试,采用割线法估算含不同等级疏松ZL205A试样的力学性能参数;基于试样断面及载荷-位移曲线分析,归纳ZL205A材料的力学行为,并通过有限元模拟对假设的力学模型进行验证。结果发现ZL205A材料的抗拉强度、伸长率、弹性模量及屈服强度指标呈现随疏松等级增加而降低的趋势,材料变形塑性屈服阶段不明显且具有脆性断裂特征。结论 Ramberg-Osgood方程适合于描述ZL205A材料的弹塑性本构关系。     

丁腈橡胶密封圈高温老化行为——自由状态和承压状态

目的研究丁腈橡胶密封圈自由状态和承压状态下的高温老化行为。方法以拉伸强度和拉断伸长率为参数,对各温度下的老化行为进行表征和分析。结果 70℃条件下机械应力大大加快了橡胶密封件拉伸强度的下降速率,以致试验64 d时拉伸强度甚至比110℃时还低,拉断伸长率的下降速率也明显加快了;90℃加速条件下机械应力对拉伸强度的下降有一定的促进作用,但对拉断伸长率的变化基本无影响;110℃加速条件下机械应力对拉伸强度和拉断伸长率均没有明显的影响。结论机械应力在较低温度下可以显著促进丁腈橡胶密封圈热氧老化,高温条件下促进作用不明显。     

活性污泥TB-EPS的絮凝特性研究:絮体的成长、破碎与再凝聚

为了解活性污泥中紧密结合胞外聚合物(tightly bound extracellular polymeric substances,TB-EPS)的絮凝特性,采用激光粒度仪在线监测技术考察了TB-EPS与高岭土生成絮体的过程以及絮体的破碎与再凝聚规律.结果表明,TB-EPS的主要组分为蛋白质和多糖聚合物,增加TB-EPS的投加量,絮体的粒径相应增大,悬浊液的剩余浊度降低.随着絮体破碎-再凝聚次数的增加,絮体的破碎因子升高而恢复因子降低,表明TB-EPS形成的絮体的强度逐渐降低,同时再凝聚的能力也逐渐降低.TB-EPS吸附高岭土的主要作用力为氢键作用,但在絮体形成过程中多糖聚合物之间的纠缠作用和蛋白质成分之间的疏水作用也可能发挥一定的作用.絮体的破碎是侵蚀和破裂同时作用的结果.     

复合生物絮凝剂CBF-1的絮凝作用机理研究

采取PAC+絮凝剂的复配方式开展高岭土悬浊液烧杯实验,考察了复合生物絮凝剂CBF-1、CBF-1溶解物及微生物絮凝剂MBF8的絮凝特性,并借助iPDA仪分析和扫描电镜、光学显微镜观察等手段,比较分析了絮凝过程及絮体特性的差异.结果表明,各复配絮凝的浊度去除效果排序为CBF-1＞ CBF-1溶解物＞MBF8,CBF-1投加量1 mg·L-1时,浊度去除率可达到97.5％;絮体强度排序为CBF-1＞ CBF-1溶解物＞MBF8,絮体恢复因子排序为MBF8＞CBF-1溶解物＞CBF-1,絮体大小排序为CBF-1＞ CBF-1溶解物＞MBF8.单独投加PAC或投加PAC+MBF8的情况下,形成的絮体形态相对规整、密实;投加PAC+ CBF-1溶解物或投加PAC+ CBF-1形成的絮体则相对无序、疏松,CBF-1作用下絮体大、沉降快.CBF-1中高电荷MBF8组分及大分子羧甲基纤维素、羧甲基多聚糖等组分具有强的电荷中和与桥联协同增效作用;CBF-1还含有纤维素、木质素等大分子量且带多种官能团的不溶性组分,在桥联和吸附过程中也起着重要作用.     

改性壳聚糖CAD与微生物絮凝剂MBF8复配絮凝研究

采用水溶液自由基聚合反应,将丙烯酰胺(AM)、二甲基二烯丙基氯化铵(DMDAAC)接枝到壳聚糖分子上制成了阳离子改性壳聚糖(CAD).经FT-IR、XRD、zeta(ξ)电位、凝胶色谱等分析确定,CAD为淡黄色透明液体,pH值为3.7,相对分子质量为2.88×10⁶,阳离子度为16.7,等电点(0.1%溶液)约为pH值10.5,有效成分2.6%,主要特征官能团有羟基、氨基、季铵基和酰胺基, 呈不规则晶体结构.将CAD与相对分子质量3.67×10⁵的多糖类电负性微生物絮凝剂MBF8复配,对浊度12~460 NTU、离子强度3.0 mmol·L^-1的高岭土悬浊液进行烧杯实验.结果表明,MBF8与CAD的最佳使用方式为先投加MBF8后投加CAD,复配比5:3时效果最好,适用的pH范围为6.0~10.0.采用PAC(3.0 mg·L^-1)+MBF8+CAD(1.0 mg·L^-1)复配絮凝,pH=8.0下,对浊度为110 NTU的高岭土悬浊液,浊度去除率>97%,残余铝<0.08 mg·L^-1,絮体大、沉降快,絮凝效果优于PAC+分子量800万、1200万的阴离子PAM及分子量1500万的阳离子PAM.