城市污水高效低耗生物脱氮工艺研究

采用活性污泥与生物膜法相结合工艺处理城市生活污水，可以高效去除污水中的有机物和NH4^ -N。研究结果表明：水力停留时间为7．5h、回流比为1．5、无外加碳源时，COD的去除率大于90％，NH4^ -N的去除率大于99％；平均出水COD小于40mg／L，NH4^ -N小于1mg／L，TN的去除率60％左右；反硝化过程的适宜C／N为4～5。     

研究单位压边力值对板料成形性能的影响

主要介绍板料在拉深成形过程中单位压边力值对板料成形性能的影响。研究方法采用仿真技术 ,指出板料在成形过程中如按最初设定的单位压边力值进行成形 ,那么 ,板料成形过程中单位压边力值将逐渐增大 ,严重影响板料成形极限。如果采用控制板料在成形过程中压边圈下坯料的单位压边力值 ,将提高板料成形极限。其结论为生产现场提高板料成形性能和表面质量提供了一种可实施的方法。     

不对称氧化铝膜管的微滤性能研究

采用熔模离心法制备的不对称氧化铝微滤膜管的孔径沿径向呈样度分布，控制层孔径均匀。最可几孔径为０．０５μｍ，最大孔径为０．１μｍ的管能滤原液中全部的细菌，获得完全无菌的水，但过滤速率太慢，最可几孔径为０．１μｍ，最大孔径为０．２μｍ、最大孔径０．３μｍ。     

膜生物反应器中膜污染研究进展

膜生物反应器是近年新发展起来的高效废水处理工艺。本文综述了国内外对膜污染机理研究的最新成果 ,介绍了相应的解决措施 ,展望了今后的发展前景。     

利用废渣废碱液年产3000t粒状五水偏硅酸钠工艺初步设计

介绍以铝矾土提取硫酸铝废渣和氧氯化锆副产废碱液为原料生产泡花碱 ,然后利用一次造粒法生产五水偏硅酸钠新工艺确定影响产品质量指标工艺因素。小试试验产品质量指标达到HG/T2 5 6 8- 94要求 ,工艺成本低 ,避免废碱液及废渣排放对环境的污染。     

物理化学预处理与膜分离技术的应用

将物理化学预处理与膜分离技术深度处理结合应用于工业废水处理，可使其中的Ｃｒ６＋＜０．５ｍｇ／ｌ，Ｚｎ２＋＜２０ｍｇ／ｌ，ｐＨ６～９。用膜分离技术处理造纸废水可回收其中的木质素和糖份，回收率均为６０％左右。     

膜生物反应器与传统活性污泥工艺除污特性比较

比较了膜生物反应器（MBR）和传统活性污泥工艺（CAS）在相同运行条件下对生活污水的除污特性.结果表明,MBR系统对COD、NH3-N和TN的平均去除率比CAS分别高14.4%、51.2%和37.3%.但MBR中膜的截留使系统相对比较封闭,制约了通过排放高磷污泥的生物法除磷,除磷效率仅为32.9%,低于CAS工艺（43.0%）;将MBR与化学除磷工艺相结合,MBR系统除磷效率可达93.3%.     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｃｏｎｔａｉｎｓａｌｏｔｋｉｎｄｓｏｆｐｏｌｌｕｔａｎｔｓ,ｓｕｃｈａｓａｃｉｄｉｃｄｙｅｓ,ｄｉｓｐｅｒｓｅｄｙｅｓ,ｍｏｒｄａｎｔｄｙｅｓ,ａｕｘｉｌｉａｒｉｅｓ,ｓａｌｔｓａｎｄｓｏｏｎ .Ｔｈｅｅｆｆｌｕｅｎｔｓｆｒｏｍｗａｓｔｅｗａｔｅｒｔｒｅａｔｍｅｎｔｐｌａｎｔｓｆｏｒｔｒｅａｔｍｅｎｔｏｆｔｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｓｗｉｔｈｎｏｒｍａｌｂｉｏｌｏｇｉｃａｌｐｒｏｃｅ…     

Test of membrane bioreactor for waste water treatment in a petrochemical complex

Membrane bioreactor (MBR) used in water and waste water treatment is a developing technique for water pollution control and water reuse. This paper describes a membrane-bioreactor for treatment of waste water in a petrochemical complex. The experimental MBR was a lab scale one composed of an activated sludge bioreactor unit and an ultrafiltration membrane unit. The relationship of COD removal with MLSS and HRT in this MBR was studied. The effects of crossflow velocity, backwash interval and volume of flush liquid on the flux were discussed. The results showed that average removal of COD, oil, SS and turbidity in petrochemical waste water by the MBR was 91%, 86%, 92% and 99% respectively. The average removal of NH₃-N and total phosphorous was 85% and 82%. A coefficient of COD removal, k, was 0.017-0.080 L/(mg.d). The membrane flux maintained higher than 60 L/hm2 bar for 34 days without chemical cleaning when the velocity of crossflow was 3.5-3.9 m/s and the backwash interval was 30 minutes and backwash duration at 20 seconds. The results indicated that it is feasible for MBR technology to be used in petrochemical waste water treatment. The treated water could be considered as a source used to make up water for industrial cooling system or to be reused for other purposes.     

人工智能在金属塑性加工领域中的应用

概述了人工智能及其 2个主要分支 (专家系统和人工神经网络 ) ,讨论了遗传算法与专家系统集成以及神经网络与模糊逻辑、专家系统集成的必要性和集成方法 ,分别介绍了专家系统和人工神经网络在塑性加工领域中的应用现状。