石油类污染物自然衰减能力现场试验验证研究

在北京地区某加油站开展的前期石油类污染物自然衰减现场试验的基础上,进一步开展了验证试验,结果表明本次试验得到的挥发性有机物(VOCs)变化趋势及O2、CO2含量沿土壤深度分布和前期试验结果呈现相同的规律,说明基于自然衰减法设计实施的加油站现场试验检测分析结果可靠,试验方法具有合理性、可操作性及可重复性.进一步的理论分析对前期试验结果进行了验证,得出以下结论:(1)通过氧平衡和碳平衡计算对加油站土壤内的自然衰减方式进行评价,验证了该加油站地下土壤中实际发生的微生物降解既有需氧降解也有厌氧降解;(2)利用有机物的一级衰减模型对该污染现场土壤中石油类污染物的降解速率和半衰期进行计算表明,2次试验计算得到的石油类污染物的半衰期基本一致,该污染现场石油类污染物的半衰期为50 d左右;(3)在此基础上,对该加油站包气带土壤的自然衰减能力和环境质量进行评价,2次试验结果均表明该污染现场在自然衰减的作用下已经不存在环境风险.     

阴极液及底物浓度对AFB-MFC同步废水处理及产电性能影响

为了提高厌氧流化床微生物燃料电池（AFB-MFC）的性能,并为双室MFC寻找价廉、易得、无污染的阴极液,在曝气量16～24 L/h、温度（35±2）℃、回流量10.2 L/h、阴极底边距阴极室内底部17.3 cm、外电阻250 Ω、水力停留时间（HRT）14.0～14.9 h以及进水pH 7.81～8.37下,研究了阴极液及底物浓度对系统产电及废水处理性能的影响。结果表明,使用缓冲溶液、阳极室出水和自来水作阴极液时,自来水的产电性能最佳,阴极液种类不影响系统有机基质的去除。以自来水为阴极液时,阴极液pH及电导率随运行时间增加而增加,COD去除率为80.11%～89.29%,输出电压及功率密度开始随运行时间增加而增加,之后稳定在440～452 mV和48.40～51.08 mW/m²之间。增加底物浓度对COD去除率影响不大,而输出电压及功率密度随底物浓度增加而下降;底物COD浓度由3 307.09 mg/L增至9 520 mg/L时,COD去除率在85.77%～94.44%之间,输出电压及功率密度则分别由449 mV和50.40 mW/m²下降至406 mV和41.21 mW/m²。自来水作阴极液可避免二次污染及阴极液对阳极室微生物的影响,并得到高的产电能力。     

复合型絮凝剂处理景观水体

利用以生物絮凝剂(1 g/L MBF-28)与化学絮凝剂(5 g/L PAC)复配后的复合絮凝剂CBF28C处理景观水体,考虑了复配比、投加量、pH和投加顺序对处理景观水的影响。实验结果表明:对于反应体系为100 mL景观水体,当MBF-28与PAC溶液复配体积比为3∶1,反应体系pH为7.0,1 mL 1%CaCl2作助凝剂,1.5 mL CBF28C时,其絮凝效果最好,其COD,色度,TN,TP的去除率分别为90.7%,54.1%、46.6%和51.5%。最佳水力条件为:快速320 r/min,快搅时间45 s,慢速80 r/min,慢搅时间100 s。并且得出了前10 min内絮凝率的反应关系方程式。     

微生物生理群在猪粪秸秆高温堆肥碳氮转化中的作用

在自制的强制通风静态堆肥反应箱中,猪粪与秸秆以鲜重7∶1的比例进行了堆肥化实验,在堆制的23 d里根据堆温变化分阶段采集堆肥样品,利用MPN法测定了堆料中纤维素分解菌和氮素微生物生理群的数量变化,同时测定了相应的碳、氮含量。结果表明,纤维素分解菌在稳定腐熟阶段较多,对于后期有机碳的降解和腐殖质含量的增大起了很大的作用,在堆制的23 d里,腐殖质增加了2.4%。整个堆制过程中,氨化细菌的数量最大且与氨气释放浓度和铵态氮含量呈显著正相关,都在高温期增加,降温期后减少,氨化细菌的数量在高温期的增加率远高于降温期后的减少率,而铵态氮在高温期的增加率远低于在降温后期的减少率,铵态氮总体上减少了74.1%;亚硝化细菌数量与硝态氮呈正相关;反硝化细菌数量在降温期上升幅度较大,堆制结束时为堆制初期的13倍,且与堆肥中硝态氮含量呈正相关;硝态氮含量增加了87.5%;堆肥后期硝态氮的增加可能与堆肥中存在能进行硝化作用的反硝化细菌有关。固氮菌数量在堆制结束时达堆制初期的2.61倍,主要在降温期增加较多,对堆肥中有机氮的形成起很大作用。     

一株产絮酵母菌废菌体对Cd2+的吸附特性

将一株产絮酵母菌(编号B-02号)发酵后的废菌体制成生物吸附剂,研究该生物吸附剂对废水中Cd2+的生物吸附特性。结果表明:(1)pH值对Cd2+会产生较大的影响,偏酸性(pH=4～6)条件利于吸附;该吸附剂对Cd2+吸附速率较快,8～10 min就可达到吸附平衡;(2)吸附剂的吸附动力学符合二级动力学模型,吸附Cd2+的实验数据对Langmuir等温式的拟合情况良好,吸附剂吸附Cd2+的最大吸附量为70.752 mg/g。用0.5 mol/L HNO3对吸附Cd2+的酵母菌进行解吸,解吸率可达89.7%。     

简单芽孢杆菌产高效微生物絮凝剂

通过从绿化植物根际土壤和污水处理厂的活性污泥中分离筛选絮凝剂产生菌,得到一株稳定高效的微生物絮凝剂产生菌PS1,根据形态学特征、生理生化实验以及16S rDNA序列分析将其鉴定为简单芽孢杆菌(Bacillus simplex)。对菌株PS1产生絮凝剂的最佳培养时间、絮凝活性分布以及pH、CaCl2、絮凝剂投量对絮凝效果的影响进行了研究,并考察了其对实际废水的絮凝效果。结果表明,菌株PS1产絮凝剂的最佳培养时间为36 h,产生的絮凝活性物质全部存在于发酵液离心后的上清液中;当pH为7.0～8.5、CaC12投量为0.25～0.35 g/L、发酵液投加量的体积分数为1.5%～2.5%时,菌株PS1发酵液对4 g/L的高岭土悬浊液的絮凝效果最佳,絮凝率达到97%。菌株PS1所产絮凝剂对城市污水、啤酒废水、淀粉废水、医院废水的絮凝率可达90%以上。     

响应曲面法优化复合絮凝剂的制备工艺

为了提高染料废水中COD和色度的去除效果,采用响应曲面法对聚硅酸类新型复合絮凝剂的制备工艺进行了优化实验研究。在单因素实验基础上采用Box-Behnken Design(BBD)实验设计方法,设计出了影响染料废水处理效果的3因素3水平共15组实验,其中n(Fe+Al):n(Si)的摩尔比为4～6,n(B+Mg):n(Si)的摩尔比为0.3～0.7,熟化时间为1～3 d。根据15组实验结果,以COD去除率和色度去除率为响应值分别建立了二次多项式响应曲面模型。模型优化结果显示,在n(Fe+Al):n(Si)摩尔比为5∶1,n(B+Mg):n(Si)为0.5∶1,熟化时间为2 d的条件下,制备得到的新型复合絮凝剂聚硅酸铝铁硼镁具有最佳的絮凝处理性能和脱色效果,能有效去除染料废水中的COD和色度,其中出水色度接近于0,COD的去除率达到87.65%,模型验证实验进一步验证了本文所建立的响应曲面法在复合絮凝剂制备工艺优化中的有效性。     

Speciation and persistence of doxycycline in the aquatic environment: Characterization in terms of steady state kinetics

The aim of the present work was to establish the kinetics for the degradation of doxycycline in the aquatic environment with a view to arriving at a kinetic model that can be used to predict the persistence of antibiotic with confidence. The degradation of doxycycline in both water and sediment phases of aquatic microcosm experiments, as well as in distilled water control experiments, was studied over a period of 90 days. An initial 21% loss due to adsorption by the sediment was observed in the microcosm experiment soon after charging. Biphasic zero-order linear rates of degradation, attributed to microbial degradation of the free and sediment or colloidal particle-adsorbed antibiotic, were observed for both water phase (2.3 × 10^?2 and 4.5 × 10^?3 μgg^?1 day^?1) and sediment phase (7.9 × 10^?3 and 1.5 × 10^?3 μgg^?1 day^?1) of the microcosm experiment. The covered distilled water control experiment exhibited a monophasic zero-order linear rate (1.9 × 10^?3 μgg^?1 day^?1) attributed to hydrolysis, while the distilled water experiment exposed to natural light exhibited biphasic liner rates attributed to a combination of hydrolysis and photolysis (2.9 × 10^?3 μgg^?1 day^?1) and to microbial degradation (9.8 × 10^?3 μgg^?1 day^?1). A kinetic model that takes into account hydrolysis, photolysis, microbial degradation as well as sorption/desorption by colloidal and sediment particles is presented to account for the observed zero-order kinetics. The implications of the observed kinetics on the persistence of doxycycline in the aquatic environment are discussed.     

Method to Partition Between Attached and Unattached E. coli in Runoff From Agricultural Lands1

Abstract: Remediation of waters impaired by bacterial indicators is usually dictated by total maximum daily load plans, which are heavily dependent on fate and transport modeling of bacterial indicators. Nonpoint source pollution models are most frequently used to assess bacterial transport to surface waters and most models typically simulate bacterial transport as a dissolved pollutant. Previous studies have found that cells preferentially attach to sediments; however, a variety of techniques have been used to assess attachment including filtration, fractional filtration, and centrifugation. In addition, a variety of chemical and physical dispersion techniques are used to release attached and bioflocculated cells from particulates. Here we developed and validated an easy‐to‐replicate laboratory procedure for separation of unattached from attached E. coli which will also identify particle sizes to which E. coli preferentially attach. Physical and chemical dispersion techniques were evaluated and a combined hand shaker treatment for 10 min followed by dilutions in 1,000 mg/l of Tween 85 significantly increased total E. coli concentrations by 31% when compared with a control. In order to separate unattached from attached fractions, two commonly used techniques, fractional filtration, and centrifugation were combined. The filtration and centrifugation treatments did not reduce E. coli concentrations when compared with a control (p > 0.05), indicating that damage was not inflicted upon the E. coli cells during the separation procedure.     

双氰胺-甲醛聚合物-聚合氯化铝复合絮凝剂的合成及应用

以双氰胺、甲醛、氯化铝为主要原料,加入添加剂合成了双氰胺-甲醛聚合物（DF）-聚合氯化铝（PAC）复合絮凝剂。采用模拟印染废水考察了各种因素对DF—PAC复合絮凝剂混凝脱色性能的影响。实验结果表明,在双氰胺、甲醛、氯化铝、添加剂加入量分别为29．1,57．8,4．8,12．5g,反应温度（70±1）℃、反应时间2．5h的条件下制得的DF—PAC复合絮凝剂的絮凝脱色性能良好,COD去除率不小于90％,色度去除率不小于99％。与PAC和DF絮凝剂相比,DF—PAC复合絮凝剂对实际印染废水的絮凝脱色效果更好。