生物气溶胶的吸湿性

归纳了有关气溶胶吸湿性的测量方法以及过去近30a来文献中报道的生物气溶胶吸湿性的主要研究成果,总结了不同种类生物气溶胶之间吸湿性的差异.已有研究表明,绝大部分的生物气溶胶粒子都具有一定的吸湿性,当相对湿度为90%时,吸湿增长因子约为1.04（真菌孢子）~1.22（细菌）,花粉颗粒物吸湿后的质量与之前的比值为1.30~1.55.最后,提出了目前关于生物气溶胶吸湿性研究中尚未解决的科学问题及该领域的主要发展方向.     

UASB启动运行特征及互营丙酸氧化菌定量分析

为揭示升流式厌氧污泥床（UASB）反应器启动运行效能与互营丙酸降解菌群数量之间的关系,以稀释的玉米淀粉生产废水为底物,考察了UASB启动期的运行特征,并采用实时荧光定量PCR技术（qPCR）分析了互营丙酸降解菌群（丙酸氧化菌和产甲烷菌）的演替规律.结果表明,在进水COD 2000mg/L和水力停留时间（HRT）24h条件下,经过38d的连续运行,COD去除率达到了91.9%.当HRT分阶段缩短至8h时,比产甲烷速率达到了315LCH₄/（kg COD·d）,且形成了沉降性能良好的颗粒污泥.qPCR检测结果表明,至少有5种已鉴定的丙酸氧化菌存在于UASB反应器中.Pelotomaculum propionicum为接种污泥中的主要丙酸氧化菌,约占检测到丙酸氧化菌总数的45.7%.它的数量随着HRT缩短不断减少.而Syntrophobacter sulfatireducens和S.wolinii的数量随着HRT缩短不断增加,并在启动完成时达到最大值,分别为1.3×10³,5.5×10³个16S rRNA基因拷贝数/ng DNA,演替成为成熟颗粒污泥中的优势丙酸氧化菌群.Methanobacterium和Methanosarcina为接种污泥中的主要氢营养型产甲烷菌和乙酸营养型产甲烷菌,其数量随着HRT的缩短而逐渐减少,而Methanospirillum和Methanosaeta的数量随HRT的缩短逐渐增加,成为成熟颗粒污泥中的优势产甲烷菌群.     

高原湖泊沉积物中反硝化微生物的群落特征——以包头南海湖为例

为了探明内蒙古高原富营养化城市湖泊中nirS型反硝化细菌群落结构的特异性,利用特异性功能基因nirS对包头市南海湖的表层沉积物进行反硝化细菌多样性测定,在分析各采样点沉积物理化指标的基础上,对各样品中nirS型反硝化细菌群落和多样性进行研究.结果表明,南海湖沉积物Shannon指数变化为3.07~3.41,相比于其他研究,反硝化微生物多样性相对较低.参与反硝化的优势菌属与大多数湖泊保持一致,以假单胞菌属（Pseudomonas）和红杆菌属（Rhodobacter）为主.冗余分析（RDA）指出,城市湖泊中的各种类型的污染物对反硝化优势菌属有明显的促进作用,红杆菌属（Rhodobacter）与硝酸盐氮、亚硝酸盐氮呈正相关,假单胞菌属（Pseudomonas）除受硝酸盐氮、亚硝酸盐氮的影响外,还与总磷呈较强的正相关.南海湖nirS型反硝化细菌中的主要菌属促进了反硝化作用,加速了南海湖氮素的去除.     

CeO2形貌结构对催化湿式空气氧化苯酚性能的影响

采用水热法、沉淀法和溶胶凝胶法制备了3种不同形貌的CeO₂催化材料,并将其用于湿式空气氧化苯酚水溶液过程中,探讨了CeO₂形貌结构对催化湿式氧化苯酚水溶液性能的影响.采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、程序升温还原（TPR）等手段对CeO₂催化材料进行了表征.结果表明,水热法制备的CeO₂催化材料表现出较好催化性能,主要原因是水热法合成的CeO₂呈现交错的纳米棒状结构,主要暴露（220）晶面,且沿着（220）晶向生长.在反应温度为200℃、空气压力为2MPa、苯酚初始浓度500mg/L的条件下,最终（240min）COD的去除率为95.5%.     

氮掺杂二氧化钛负载钒磷氧催化氧化NO的实验研究

以VPO为活性组分,N掺杂TiO 2为载体,采用浸渍法制备了VPO/TiN催化剂,基于单因素实验研究了其对NO的选择性催化氧化(SCO)性能以及抗硫抗水性能。研究表明:当P/V为1/5、N/Ti为1、活性组分负载量为10%、焙烧温度为350℃时,催化剂的SCO活性最好,NO氧化率达到61%;光致发光光谱(PL)表征显示N掺杂TiO 2在催化剂表面形成的氧空位可增强催化剂对O 2的吸附;VPO/TiN催化剂抗硫抗水性能较强,反应后的催化剂表面未发现硫酸根的特征峰,水蒸气主要通过与NO竞争吸附占据活性位点来抑制催化剂的SCO活性。     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

Seasonal variation and size distribution of biogenic secondary organic aerosols at urban and continental background sites of China

Size-resolved biogenic secondary organic aerosols(BSOA) derived from isoprene and monoterpene photooxidation in Qinghai Lake, Tibetan Plateau(a continental background site) and five cities of China were measured using gas chromatography/mass spectrometry(GC/MS). Concentrations of the determined BSOA are higher in the cities than in the background and are also higher in summer than in winter. Moreover, strong positive correlations(R2= 0.44–0.90) between BSOA and sulfate were found at the six sites,suggesting that anthropogenic pollution(i.e., sulfate) could enhance SOA formation,because sulfate provides a surface favorable for acid-catalyzed formation of BSOA. Size distribution measurements showed that most of the determined SOA tracers are enriched in the fine mode( 3.3 μm) except for cis-pinic and cis-pinonic acids, both presented a comparable mass in the fine and coarse( 3.3 μm) modes, respectively. Mass ratio of oxidation products derived from isoprene to those from monoterpene in the five urban regions during summer are much less than those in Qinghai Lake region. In addition, in the five urban regions relative abundances of monoterpene oxidation products to SOA are much higher than those of isoprene. Such phenomena suggest that BSOA derived from monoterpenes are more abundant than those from isoprene in Chinese urban areas.     

硫酸盐还原菌对EH40焊接钢海水腐蚀的影响

目的研究无菌和SRB体系中EH40钢焊接接头的母材区、热影响区和焊缝区腐蚀差异。方法利用金相显微镜观察、失重法、电化学测试、扫描电镜和X射线光电子能谱仪等分析手段。结果焊缝区微观组织由块状铁素体(BLF)和魏氏组织(W)组成;热影响区可再分为粗晶区(CGHAZ)和细晶区(FGHAZ)两个区;母材区主要由BLF、AF和少量珠光体组成。在无菌对照体系中,焊缝区腐蚀速率为0.0026 mm/a,混合区次之,为0.0023 mm/a,母材区最小,为0.0019 mm/a。含SRB体系中,各区的腐蚀速率为:焊缝区(0.0037 mm/a)混合区(0.0034 mm/a)母材区(0.0030 mm/a)。热影响区腐蚀产物形貌粗大,点蚀孔也较大。结论焊缝区比母材区容易腐蚀,由此易造成小阳极大阴极加速腐蚀,热影响区容易发生点蚀。SRB能促进三个区域试样腐蚀加速。     

Characterization of microbial communities from coastal waters using microarrays

Molecular methods, including DNA probes, were used to identify and enumerate pathogenic Vibrio species in the Chesapeake Bay; our data indicated that Vibrio vulnificus exhibits seasonal fluctuations in number. Our work included a characterization of total microbial communities from the Bay; development of microarrays that identify and quantify the diversity of those communities; and observation of temporal changes in those communities. To identify members of the microbial community, we amplified the 16S rDNA gene from community DNA isolated from a biofilm sample collected from the Chesapeake Bay in February, 2000. The resultant 75 sequences were 95% or more similar to 7 species including two recently described Shewanella species, baltica and frigidimarina, that have not been previously isolated from the Chesapeake. When the genera of bacteria from biofilm after culturing are compared to those detected by subcloning amplified 16S fragments from community DNA, the cultured sample exhibited a strong bias. In oysters collected in February, the most common bacteria were previously unknown. Based on our 16S findings, we are developing microarrays to detect these and other microbial species in these estuarine communities. The microarrays will detect each species using four distinct loci, with the multiple loci serving as an internal control. The accuracy of the microarray will be measured using sentinel species such as Aeromonas species, Escherichia coli, and Vibrio vulnificus. Using microarrays, it should be possible to determine the annual fluctuations of bacterial species (culturable and non-culturable, pathogenic and non-pathogenic). The data may be applied to understanding patterns of environmental change; assessing the health of the Bay; and evaluating the risk of human illness associated with exposure to and ingestion of water and shellfish.     

Preparation of rare-earth metal complex oxide catalysts for catalytic wet air oxidation

Catalytic wet air oxidation (CWAO) is one of the most promising technologies for pollution abatement. Developing catalysts with high activity and stability is crucial for the application of the CWAO process. The Mn/Ce complex oxide catalysts for CWAO of high concentration phenol-containing wastewater were prepared by coprecipitation. The catalyst preparation conditions were optimized by using an orthogonal layout method and single-factor experimental analysis. The Mn/Ce serial catalysts were characterized by Brunauer-Emmett-Teller (BET) analysis and the metal cation leaching was measured by inductively coupled plasma torch-atomic emission spectrometry (ICP-AES). The results show that the catalysts have high catalytic activities even at a low temperature (80°C) and low oxygen partial pressure (0.5 MPa) in a batch reactor. The metallic ion leaching is comparatively low (Mn<6.577 mg/L and Ce<0.6910 mg/L, respectively) in the CWAO process. The phenol, COD_Cr, and TOC removal efficiencies in the solution exceed 98.5% using the optimal catalyst (named CSP). The new catalyst would have a promising application in CWAO treatment of high concentration organic wastewater. Translated from Techniques and Equipment for Environmental Pollution Control, 2005, 6(2): 40–44 [译自: 环境污染治理技术与设备]