钠基蒙脱土对亚甲基蓝的吸附和解吸研究

采用正交实验方法,确定了钠基蒙脱土吸附亚甲基蓝染料的最佳吸附条件.采用试剂再生法、超声波法、高温焙烧法、氢氧化钠—高温焙烧结合法对钠基蒙脱土吸附亚甲基蓝进行解吸.用扫描电子显微镜照片和红外光谱对吸附前后的钠基蒙脱土的结构进行表征.实验结果表明:在亚甲基蓝溶液pH为10、吸附温度为60℃、亚甲基蓝质量浓度为1 300 m...     

微电解/斜板沉淀/生物接触氧化处理印刷电路板废水

根据某印刷电路板企业生产废水的水质特点,对废水进行分类收集处理后,采用微电解/斜板沉淀/生物接触氧化工艺处理综合废水。工程运行结果表明,该工艺处理效果稳定,出水水质符合《污水综合排放标准》(GB 8978-1996)的一级排放标准。     

Fuel efficiency improvement of a dual-fuel engine fuelled with Honge oil methyl ester (HOME)–bioethanol and producer gas

Renewable and alternative fuels have numerous advantages compared with fossil fuels as they are renewable and biodegradable and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues (Yaliwal et al. 2013. International Journal of Sustainable Engineering, doi:10.1080/19397038.2013.801530. Zhu et al. 2011a, Applied Thermal Engineering 31 (14–15): 2271–2278; Zhu et al. 2011b, Fuel 90: 1743-1750; Banapurmath, Tewari, and Hosmath 2008, Renewable Energy 33: 2007-2018; Banapurmath 2009, “Performance, Combustion and Emission Characteristics of a Single Cylinder Direct Injection CI Engine Operated on Dual Fuel Mode Using Honge Oil and Producer Gas.” PhD thesis, 1–195; Banapurmath et al. 2011, Waste and Biomass Valorization 2: 1–11). In this context, the main objective of the present work is to study methods of biofuel production such as Honge oil methyl ester (HOME) using a conventional transesterification process and bioethanol from the Calliandra calothyrsus shrub using a new pretreatment method known as hydrothermal explosion. Further, experimental investigations were carried out on a single-cylinder, four-stroke, direct-injection stationary diesel engine operating in a dual-fuel mode using HOME, bioethanol and producer gas combinations to determine its performance, combustion and emission characteristics. The performance of the dual-fuel engine was analyzed at optimized engine conditions. HOME-Bioethanol (BE) blends such as HOME+ 5% bioethanol (BE5), HOME+ 10% bioethanol (BE10) and HOME+ 15% bioethanol (BE15) were prepared by adding bioethanol to HOME (on volume basis) in different proportions ranging from 5 to 15% with an increment of 5%. In this present work, the effect of different BE blends on the performance of producer gas fuelled dual fuel engine was studied. Experimental investigation on dual fuel engine using BE5-Producer gas operation resulted in up to 4–9% increased brake thermal efficiency with decreased hydrocarbon (HC), carbon monoxide (CO) and marginally increased nitric oxide (NOx) emission levels compared to HOME-Producer gas, BE10-producer gas and BE15-producer gas mode of operation. However, it was observed that, the overall performance of BE-producer gas operation was found to be lower compared to diesel-producer gas operation.     

Performance,combustion and emission characteristics of a single-cylinder,four-stroke,direct injection diesel engine operated on a dual-fuel mode using Honge oil methyl ester and producer gas derived from biomass feedstock of different origin

Renewable and alternative fuels have numerous advantages compared with fossil fuels, as they are renewable and biodegradable, and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues. In this context, present work was carried out to investigate the feasibility of alternative and renewable fuels derived from biomass feedstock of different origin for engine applications. The present study was also extended to study the effect of producer gas composition derived from different biomass feedstock on the performance, combustion and emission characteristics of a single-cylinder, four-stroke, direct injection stationary diesel engine operated on a dual-fuel mode using Honge oil methyl ester (HOME) and producer gas induction. The performance of the engine was evaluated with a constant injection timing of 27° before top dead centre, an injection pressure of 205 bar for the diesel–producer gas combination and 230 bar for the HOME–producer gas combination and a compression ratio of 17.5. The results showed that the performance of the dual-fuel engine varies with the composition of the producer gas and depends on the type of biomass feedstock used in the gasifier. Experimental investigations on the dual-fuel engine showed that brake thermal efficiency values for the engine operated using HOME–producer gas derived from babul, neem and honge woods were found to be 17.2, 14.3 and 11.56% respectively, compared to 23.8% for diesel–producer gas operation at 80% load. However, the results showed better engine performance with lower exhaust emission levels for the operation of HOME–producer gas derived from the ordinary or babul wood compared with the operation of that derived from the neem and Honge woods. In view of this, present study reveals that use of alternative and renewable fuels for dual fuel engine can be considered as an immediate solution for the development of rural areas and emergency use in the event of severe diesel fuel shortage.     

铁盐与铝盐对腈纶废水生化出水混凝特性的对比

针对腈纶废水生化单元出水,对比研究了Al2(SO4)3和Fe2(SO4)3在不同絮凝剂投量和p H时的混凝处理效果,并利用紫外-可见分光光度法(UV-Vis)、三维荧光光谱(EEM)、凝胶渗透色谱(HPSEC)等对混凝特性进行了初步探讨。研究显示,2种混凝剂在投量为63.5 mg/L时可获得30%以上的COD去除率,且最佳p H为中性附近。当投量小于32 mg/L时,Al2(SO4)3较Fe2(SO4)3具有更高的COD去除率,进一步增大混凝剂的投量很难提高Al2(SO4)3对COD的去除率,而Fe2(SO4)3则在有限范围内能持续提高COD去除率。EEM光谱分析显示,与Al2(SO4)3相比,Fe2(SO4)3对有机物具有更广的处理范围和更好的去除效果。HPSEC分析表明,Fe2(SO4)3相对于Al2(SO4)3在去除重均分子量为2 776、1 856和1 325 Da的有机物组分方面具有优势。铁盐或铝盐混凝是深度净化腈纶废水生化单元出水的可行方案之一。     

采用水解酸化-复合好氧处理制药工业废水的工艺评价

以制药工业综合废水处理为例对其采用的两级水解酸化复合好氧工艺的处理效果进行评估。按常规指标进行评估,该工艺对于制药综合废水的处理效果达到了设计目的,COD去除率可达到78.2%以上,NH+4-N的去除率达到99.3%,出水质量基本满足"污水综合排放标准(GB8978-1996)"二级标准和"辽宁省污水综合排放标准(DB21.1627-2008)";急性毒性的检测表明,经过该工艺处理后出水为低毒性;三维荧光谱分析(EEM)表明,制药综合废水经生物处理后的可溶性有机物中仍然存在难降解物质,建议增加物化处理以提高处理效果;并且制药废水经处理后的出水中的盐度对排入的生态系统存在风险,建议纳入排放标准以加强管理。     

改性糠醛渣吸附脱硫废水中钙离子

石灰石-石膏法烟气脱硫技术中石灰石利用率低导致钙流失严重,为实现脱硫废水中Ca2+的资源化利用,进行糠醛渣改性和Ca2+的吸附特性研究。实验结果表明,利用H3PO4改性后的糠醛渣对脱硫废水中Ca2+具有较高的吸附率;在振荡的前30 min吸附率上升极快,至90 min时基本达到平衡吸附量;对Ca2+浓度对吸附率影响研究结果表明,平衡吸附量与平衡浓度关系符合Langmuir等温吸附方程;在初始Ca2+浓度为300 mg/L的溶液中加入3 g吸附剂,温度30℃条件下振荡90 min,平衡吸附量为8.41 mg/g。     

电镀综合废水对DF膜的污染

江苏某电镀厂的电镀综合废水在采用DF膜进行预处理时,膜易受到污染。针对这一问题,采用DF膜生产厂家提供的小试装置,研究探索了膜污染的原因及其具体特征。实验结果表明,在处理电镀综合废水时,DF膜的污染速率较快,而酸洗对DF膜的恢复性较好,研究还证实电镀综合废水中的无氰沉锌水洗液是造成DF膜污染的主要原因。     

蒽醌修饰石墨毡电极预处理头孢合成废水

以钛涂钌电极为阳极、自制蒽醌修饰石墨毡电极为阴极,对头孢合成废水(COD=25 000~30 000 mg/L、ρ(NH3-N)=850~1 300 mg/L、色度为2 300~2 680度)进行了电化学氧化预处理,优化了电解条件,并对电化学体系的动力学和稳定性进行了分析。实验结果表明:蒽醌的存在可改善电化学氧化降解效果;在电解时间50 min、电流密度0.14 A/cm2、Na2SO4浓度0.1 mol/L、极板间距2 cm、初始废水p H 7.0的条件下,废水的COD、色度、NH3-N的去除率分别可达45.3%,66.9%,33.6%;BOD5/COD由处理前的0.27增至0.40,可生化性得到改善;COD、色度、NH3-N的电化学氧化降解过程均近似符合一级动力学方程;且该电化学体系的应用稳定性良好。     

丙烯腈生产废水中聚合物的资源化利用

以丙烯腈生产废水中的丙烯腈低聚物为原料制备聚丙烯酰胺。通过正交实验考察了水解反应条件和交联反应条件对反应的影响。FTIR表征结果显示,丙烯腈低聚物中的氰基已完全水解为酰胺基,产物聚丙烯酰胺中含有酰胺基和羧基。实验结果表明,在自来水加入量100 m L、水解反应温度95℃、m(Na OH)∶m(丙烯腈低聚物)=2.0、水解反应时间3 h的最佳水解反应条件,交联反应温度60℃、质量分数37%~40%的甲醛加入量6 m L、交联反应时间2 h的最佳交联反应条件下,处理20 g丙烯腈低聚物,可得到产物聚丙烯酰胺14.50 g,聚丙烯酰胺的水解度为21.1%、相对分子质量为2.7×106。产品性能满足Q/SH 0046—2007《钻井液用聚丙烯酰胺技术要求》中部分水解聚丙烯酰胺的性能要求。