微曝气Fenton氧化法处理模拟双酚A废水的效果及其生物验证

研究了微曝气Fenton氧化法关键工艺参数对模拟双酚A（BPA）废水处理效果的影响,并从活性污泥性质和污染物去除率两方面,采用膜生物反应器(membrane bioreactor, MBR)对微曝气Fenton氧化法的处理效果进行了实验验证,为实现BPA废水的生物处理奠定基础。结果表明,初始pH值、反应时间、H₂O₂/COD(质量浓度比)、H₂O₂/Fe²⁺ (摩尔浓度比)、反应温度及曝气量均对预处理效果有较大影响,在最佳条件下,COD去除率可达70%,BOD/COD值则由原废水的0.02提高到0.50以上。MBR处理上述出水的结果表明,经微曝气Fenton氧化处理BPA的废水,可较好地适应后续的生化处理。     

花叶芦竹水平潜流人工湿地脱氮性能研究

采用花叶芦竹水平潜流人工湿地处理生活污水,对其脱氮性能进行研究。结果表明：在HRT＝5 d,对TOC,NH⁺₄-N,NO^-₂-N,NO^-₃-N和TN的去除效果分别达到92％、93％、84％、51％和88％,相应空白湿地的去除率分别为91％、85％、-232％、-203％和66％。大部分TOC在湿地的前端被去除。花叶芦竹可以直接吸收氮素,向湿地输送氧气,通过根系分泌物提供碳源。因此,花叶芦竹人工湿地具有很好的硝化反硝化能力,实现了良好的脱氮性能。     

高效菌藻塘系统对农村污水中磷的强化去除效果研究

研究了高效菌藻塘系统处理太湖地区农村生活污水除磷效果及其强化措施。高效菌藻塘和水生生物塘HRT分别为8 d和4 d,进水总磷浓度为1.7～17.1 mg/L,出水总磷浓度全年平均值为3.33 mg/L,高效菌藻塘系统的除磷能力欠佳。通过降低水生生物塘内水深、采用废弃石膏作为填料构建了新型复合水生生物塘,HRT=1.6 d条件下,复合水生生物塘出水总磷可保持在1 mg/L以下,可达到GB18918-2002一级B排放标准。     

太阳光Fenton法处理垃圾渗滤液中有机污染物

研究利用太阳光Fenton法处理垃圾渗滤液。根据太阳光辐射强度随时间的变化规律,选择重庆7、8月份的晴天,在中午12：00到下午14：00时进行试验,研究太阳光辐射时间、pH值、Fenton试剂用量对垃圾渗滤液COD去除率的影响。研究结果表明：太阳光Fenton法对垃圾渗滤液的COD有较好的去除效果,COD去除率达86.2%。太阳光Fenton法处理垃圾渗滤液的优化条件是：日光辐射时间为120 min,pH值为2.5,Fe²⁺浓度为5 mmol/L,H₂O₂浓度为570 mmol/L。同时,论文还对太阳光Fenton法处理垃圾渗滤液的动力学进行分析。研究结果显示：太阳光Fenton法处理垃圾渗滤液,其表观动力学方程为-dC/dt=2.6×10^-8×P^1.92×F^1.79×E^1.67。     

Anaerobic ammonium oxidation by Nitrosomonas spp. and anammox bacteria in a sequencing batch reactor

A sequencing batch reactor (SBR) was inoculated with mixed nitrifying bacteria from an anoxic tank at the conventional activated sludge wastewater treatment plant in Nongkhaem, Bangkok, Thailand. This enriched nitrifying culture was maintained under anaerobic conditions using ammonium (NH(4)(+)) as an electron donor and nitrite (NO(2)(-)) as an electron acceptor. Autotrophic ammonium oxidizing bacteria survived under these conditions. The enrichment period for anammox culture was over 100 days. Both ammonium and nitrite conversion rates were proportional to the biomass of ammonium oxidizing bacteria; rates were 0.08 g N/gV SS/d and 0.05 g N/g VSS/d for ammonium and nitrite, respectively, in a culture maintained for 3 months at 42 mg N/L ammonium. The nitrogen transformation rate at a ratio of NH(4)(+)-N to NO(2)(-)-N of 1:1.38 was faster, and effluent nitrogen levels were lower, than at ratios of 1:0.671, 1:2.18, and 1:3.05. Fluorescent in situ hybridization (FISH) was used to identify specific autotrophic ammonium oxidizing bacteria (Nitrosomonas spp., Candidatus Brocadia anammoxidans, and Candidatus Kuenenia stuttgartiensis). The ammonium oxidizing culture maintained at 42 mg N/L ammonium was enriched for Nitrosomonas spp. (30%) over Candidati B. anammoxidans and K. stuttgartiensis (2.1%) while the culture maintained at 210 mg N/L ammonium was dominated by Candidati B. anammoxidans and K. stuttgartiensis (85.6%). The specific nitrogen removal rate of anammox bacteria (0.6 g N/g anammox VSS/d) was significantly higher than that of ammonium oxidizing bacteria (0.4 g N/g Nitrosomonas VSS/d). Anammox bacteria removed up to 979 mg N/L/d of total nitrogen (ammonium:nitrite concentrations, 397:582 mg N/L). These results suggest significant promise of this approach for application to wastewater with high nitrogen but low carbon content, such as that found in Bangkok.     

Fluoride removal by a continuous flow electrocoagulation reactor

Long-term consumption of water containing excessive fluoride can lead to fluorosis of the teeth and bones. Electrocoagulation (EC) is an electrochemical technique, in which a variety of unwanted dissolved particles and suspended matter can be effectively removed from an aqueous solution by electrolysis. Continuous flow experiments with monopolar aluminium electrodes for fluoride removal were undertaken to investigate the effects of the different parameters such as: current density (12.5-50A/m(2)), flow rate (150-400 mL/min), initial pH (4-8), and initial fluoride concentration (5-25mg/L). The highest treatment efficiency was obtained for the largest current and the removal efficiency was found to be dependent on the current density, the flow rate and the initial fluoride concentration when the final pH ranged between 6 and 8. The composition of the sludge produced was analysed using the X-ray diffraction (XRD) spectrum. The strong presence of the aluminium hydroxide [Al(OH)(3)] in the above pH range, which maximizes the formation of aluminium fluoride hydroxide complex [Al(n)F(m)(OH)(3n-m)], is the main reason for defluoridation by electrocoagulation. The results obtained showed that the continuous flow electrocoagulation technology is an effective process for defluoridation of potable water supplies and could also be utilized for the defluoridation of industrial wastewater.     

臭氧同时脱硫脱硝技术研究进展

对利用臭氧同时脱硫脱硝技术进行了综述,分析了臭氧对NOx的脱除机理。臭氧同时脱硫脱硝技术具有明显的一体化脱除特性,但臭氧的发生费用却制约了它的应用。介绍了目前国外在工程上应用的低温氧化技术（LOTOX）,分析了其脱除效果及优缺点。     

Biosorption of nickel(II) from aqueous solution by Aspergillus niger: Response surface methodology and isotherm study

In the present study, the effects of biosorbent Aspergillus niger dosage, initial solution pH and initial Ni(II) concentration on the uptake of Ni(II) by NaOH pretreated biomass of A. niger from aqueous solution were investigated. Batch experiments were carried out in order to model and optimize the biosorption process. The influence of three parameters on the uptake of Ni(II) was described using a response surface methodology (RSM) as well as Langmuir and Freundlich isotherm models. Optimum Ni(II) uptake of 4.82 mg Ni(II) g⁻¹ biomass (70.30%) was achieved at pH 6.25, biomass dosage of 2.98 g L⁻¹ and initial Ni(II) concentration of 30.00 mg L⁻¹ Ni(II). Langmuir and Freundlich were able to describe the biosorption isotherm fairly well. However, prediction of Ni(II) biosorption using Langmuir and Freundlich isotherms was relatively poor in comparison with RSM approaches. The biosorption mechanism was also investigated by using Fourier transfer infrared (FT-IR) analysis of untreated, NaOH pretreated, and Ni(II) loaded A. niger biomass.     

电袋复合除尘器的滤料试验与应用

清灰周期与阻力是除尘器的主要技术性能指标。本文研究了粉尘浓度及荷电粉尘对清灰周期与阻力的影响,总结了影响电袋复合除尘器性能的主要因素,介绍了电袋复合除尘器的应用实例,并分析了电袋复合除尘器的适用性。     

Modification of Fe–Mn mixed oxide COS removal sorbent by rare-earth oxides addition

In order to develop highly active sorbent for COS removal, Fe–Mn mixed oxides doped with CeO₂, La₂O₃ or Sm₂O₃ were studied. The effects of these promoters on the structural properties of Fe–Mn oxides were investigated by XRD, BET, TPR and TEM techniques. XRD results revealed that the degree of crystallinity of Fe–Mn oxide phase decreased due to the addition of rare-earth oxides. Doping with CeO₂, La₂O₃ or Sm₂O₃ led to an increase in BET surface area of the sample. TPR studies showed that the reactivity of the reduction of doped samples increased in the temperature range of 300–450 °C. In addition, the desulfurization test was performed at 325 °C with a gas hourly space velocity of 1000 h⁻¹. It was found that the addition of 3% La₂O₃ greatly improved the absorption sulfur capacity of the sorbent, while the sorbent doped 3% CeO₂ achieved a sufficiently high purifying degree before breakthrough.