磷酸铵镁碱促(Mg(OH)_2)热解产物氨氮去除性能

磷酸铵镁热解循环技术可以有效降低磷酸铵镁结晶技术的药剂费用。同时,在磷酸铵镁热解过程中添加Mg(OH)2碱促媒介,能阻止磷酸氢镁向焦磷酸镁的转化,并降低热解产物氨氮去除过程中上清液磷酸盐的残留。在Mg(OH)2∶NH+4摩尔比为1∶1,热解温度为110℃条件下,热解产物沉氨效率接近84%,上清液磷酸盐残留量为0.02 mg/L。     

固定化斜生栅藻净化畜禽废水中氨氮和磷的影响因素

为探讨Cu2+、p H和流速对固定化斜生栅藻去除畜禽废水中NH+4-N、TP效果的影响,在实验室条件下模拟实际污水处理过程,并采用正交实验方案对结果进行分析。结果表明低质量浓度Cu2+(0~0.05 mg/L)改善藻的净化效果,高质量浓度Cu2+(0.50~5.00 mg/L)抑制藻的净化效果;在p H较高的条件下(p H=9),固定化斜生栅藻的净化效果明显提高;流速对结果没有明显影响。通过正交实验,得出固定化斜生栅藻去除畜禽废水中NH+4-N、TP的优化条件如下:Cu2+质量浓度为0.05 mg/L,p H为9,流速为0.3 m/s。此时NH+4-N去除率为96.11%,TP去除率为97.53%。     

300MW燃煤锅炉机组超细颗粒聚并器的实验研究

为了解决燃煤锅炉烟气中超细颗粒难以脱除的问题,基于流体动力学原理设计了一种超细颗粒聚并器,并在300 MW燃煤锅炉机组电除尘器的前置烟道中进行了实验研究。结果表明,聚并器内部存在超细颗粒之间以及超细颗粒与大颗粒之间的相互聚集行为,从而使超细颗粒数量显著减少。例如,对于粒径在2.65和10.48μm以下的颗粒,其体积比例在聚并器出口分别减少了56.7%和62.3%,在电除尘器出口的粉尘浓度减少了26.34 mg/Nm3,这表明,基于流体动力学原理的聚并器对超细颗粒的聚并作用明显,具有良好的应用前景。     

声凝并联合雾化预处理及其在过滤除尘中的应用

根据声凝并理论和雾化湿式除尘理论,建立了燃煤飞灰在声场联合雾化加湿作为预处理的过滤式除尘实验装置。分别在声场、雾化加湿、声场与雾化加湿相结合3种预处理条件下进行实验,确定合适的加湿量范围,得出不同条件下燃煤飞灰的去除效果。在声场联合雾化加湿条件下,分别研究了声压级和雾化加湿量对飞灰的去除率的影响。结果表明,声场和雾化加湿联合作用能有效提高燃煤PM2.5去除率。以声场联合雾化加湿作为预处理进行过滤除尘实验,结果表明,虽然对高效滤料的除尘效率提高作用有限,但是该预处理可减轻滤袋负荷,有效延缓压差增长,降低清灰频率。由于采用表面覆膜滤材,加湿量控制得当可避免产生"糊袋"现象。     

水华束丝藻与铜绿微囊藻净化水体氮磷及其脂质积累过程比较

选取水华束丝藻与铜绿微囊藻作为典型水华蓝藻,探索水华蓝藻净化水体及合成生物柴油的潜力.采用氮磷浓度为NH4-N 7.5 mg/L,PO43--P 1.0 mg/L的模拟污水,重点考察了在光照强度与温度不同的条件下2种微藻对氮磷的去除率,并利用尼罗红荧光染色法测定了微藻中的中性脂含量.结果表明,2种藻对PO43--P的去除率均较高,最高达到98％,对NH4+-N的去除率稍低,最高为52％.水华束丝藻及铜绿微囊藻均具有较强积累中性脂的能力,适宜的温度与光照条件有利于微藻对氮磷的去除及细胞中脂类的积累.2种藻均在光照强度为12 000 lx时中性脂含量更高.水华束丝藻在温度为18 ～22℃条件下,生长更优,氮磷净化效果较好,中性脂积累能力更强.而铜绿微囊藻在温度为22～ 26℃时表现更好.     

抗生素废水的铁屑微电解预处理研究

研究了采用铁屑微电解法预处理抗生素废水.在进水COD质量浓度为6.2 g/L时,试验结果表明,经微电解处理后的废水,COD和色度的去除率分别达到68.3%和79.3%,BOD5/COD从0.306提高到0.56,废水的可生化性得到显著提高.通过正交试验考察pH、反应时间及铁屑用量对处理效果的影响,并对各因素作了单因素影响试验,确定了最佳工艺条件.     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

Diffusion mechanism of lindane into wood charcoal

Abstract

The wood charcoal treated by 1N HNO₃ (WCT) was used to remove toxic chlorinated pesticide lindane (y‐HCH) residue from water by the sorption process. Using a simple first order reversible kinetics constants and half time equations, the film and pore diffusion coefficients were determined. Film diffusion was found to be rate limiting step in sorbing lindane by WCT. This was further authenticated by kinetics studies at different initial sorbate concentrations, different sorbent sizes, and different agitation speeds besides interruption test. A pore diffusion model was used to fit the data of kinetics in continuously mixed batch reactors (CMBR), and the tortuosity, external resistance, and surface diffusion effects on lindane sorption by WCT were noticed. The tortuosity values of 15 to 28 were obtained for WCT‐lindane system.     

Adsorption of simazine on zeolite H-Y and sol–gel technique manufactured porous silica: A comparative study in model and natural waters

In this work, we studied the removal of simazine from both a model and well water by adsorption on two different adsorbents: zeolite H-Y and a porous silica made in the laboratory by using the sol–gel technique. The pH dependence of the adsorption process and the isotherms and pseudo-isotherms of adsorption were studied. Moreover, an iterative process of simazine removal from both the model and well water, which allowed us to bring the residual simazine concentration below the maximum concentration (0.05 mg L^?1) of agrochemicals in wastewater to be released in surface waters or in sink allowed by Italian laws, was proposed. The results obtained were very interesting and the conclusions drawn from them partly differed from what could reasonably be expected.     

电解法处理含镍废水及纯镍的回收

采用电解回收法处理Ni2+含量为2g/L的废水,在阴极回收纯镍。研究了电解电流、极距、NH4Cl浓度、pH值等因素对Ni2+去除率、槽压、阴极能耗的影响,得出最优工艺参数为:温度20℃,电解时间20min时、电解电流300mA,极距15mm,NH4Cl浓度5g/L,pH值8.0,该条件下Ni2+去除率为96.926%,槽压16.21V,阴极能耗22.418kW.h/kg,在阴极可得到沉积6.45μm厚的镍板。