EGSB-MBR组合工艺处理糖蜜发酵废水效能研究

实验采用厌氧膨胀颗粒污泥床(EGSB)反应器与好氧膜生物反应器(MBR)组合工艺对糖蜜发酵废水进行处理.重点考察了组合工艺对发酵废水的处理效能,包括甲烷的产生效率、污染物(COD、NH4+-N和TN)的去除效能.实验结果表明:控温条件下[(35±1)℃]、进水COD约为2250mg/L、pH在为6.0左右时,EGSB对发酵废水的COD去除率可达75.6%,甲烷的容积产气速率为0.48m3/(m3·d).MBR在溶解氧(DO)为1~2mg/L左右时,采用曝气-搅拌交替运行方式处理EGSB出水,可以实现同步硝化反硝化,并且在曝气3h-搅拌1h交替运行条件下,NH4+-N、TN去除率分别为85.13%、58.57%,而最终COD去除率达到85%.     

燃煤电厂产生和排放的PM2.5中水溶性离子特征

为了认识我国燃煤电厂一次PM2.5排放特征,并定量评估大规模开展烟气脱硫与脱硝对其影响,本研究选取了国内一个煤粉炉电厂和一个循环流化床电厂,对其产生和排放的PM2.5进行现场测试,并进行水溶性离子组分的分析.结果表明,在所测的这两个电厂中,循环流化床电厂产生的PM2.5的质量浓度高于煤粉炉电厂产生的PM2.5的质量浓度,但是这两个电厂排放的PM2.5的质量浓度相当.产生此结果的主要原因是该循环流化床电厂配备的电袋复合除尘器比煤粉炉电厂的普通电除尘器对PM2.5去除效率更高.煤粉炉电厂产生PM2.5中水溶性离子浓度低于循环流化床电厂,但是煤粉炉电厂排放PM2.5中水溶性离子浓度却远远高于循环流化床电厂,表明煤粉炉电厂排放的PM2.5受脱硫和脱硝设施的影响较大.煤粉炉烟气脱硝过程中可能形成硫酸雾,烟气中的部分硫酸雾和过剩的NH3反应生成NH4HSO4进入颗粒相,同时降低了PM2.5的p H值;而脱硫过程中脱硫液的夹带也会导致NH+4和SO2-4进入PM2.5.所以,虽然两个电厂产生的PM2.5中水溶性离子均以Ca2+和SO2-4为主,但煤粉炉排放PM2.5中的水溶性离子则以NH+4和SO2-4为主.     

滴流床催化湿式氧化苯酚的动力学

通过自行设计制作的滴流床反应器,研究了苯酚在以CuO/γ-Al₂O₃为催化剂的催化湿式氧化反应.结果表明,在相对温和的操作条件(温度180 ℃,压力3 MPa,液相流量1.668 L·h^-1,气相流量160 L·h^-1)下,苯酚的去除率均达到90%以上.苯酚的降解曲线与自催化反应的S型曲线类似,符合自由基链反应机理.所建立的活塞流拟均相反应器模型能很好地拟合苯酚催化湿式氧化反应过程.还研究了苯酚初始浓度、苯酚水溶液流量及反应温度对反应结果的影响.     

磁态厌氧流化床处理印染废水

在厌氧流化床中投加高效脱色菌种;采用聚集—交联固定法,将脱色菌固定于活性污泥上;在反应器内投加磁粉形成稳恒弱磁场,对微生物产生正的磁生物效应来提高生化反应速率,处理人工模拟印染废水。试验结果表明,水力停留时间3h,色度去除率90％以上CODcr去除率44％～49％。与传统生化法相比,该装置投资省,成本低,处理效果良好。启动快,耐冲击负荷,停留时间短,操作管理方便。在实际应用中有广阔的前景。     

人工片状钙基脱硫剂的试制及其性能研究

介绍了用于沸騰炉燃煤锅炉脱硫的人工片状钙基脱硫剂的生产工艺,并用固定床反应器、压汞仪,扫描电子显微镜、强度仪等研究了该脱硫剂的物理化学特性。实验表明,采用该工艺生产的脱硫剂具有良好的抗压抗磨强度和耐水性,由于具有合理的孔分布,其固硫能力是石灰石的2—3倍,钙利用率可达40％,适用于850℃—1000℃的较宽温度范围。在3台沸腾炉共7个工况下的工业实验证明了该脱硫剂的上述特性。     

废FCC催化剂对水中铅离子的连续吸附及脱附

通过测定吸附等温线，考察了Ｐｂ２＋在废ＦＣＣ（流化催化裂化）催化剂上的吸附性能及规律，结果表明，Ｐｂ２＋在废ＦＣＣ催化剂上的吸附规律可用Ｌａｎｇｍｕｉｒ和Ｆｒｕｎｄｌｉｃｈ模式描述，吸附呈单分子层形式且容易进行。又通过填充床吸附试验，对Ｐｂ２＋的连续吸附及脱附情形作了考察。结果表明，在温度为１５℃、ｐＨ为５．１３、过柱速率为３．０ｍＬ／ｍｉｎ、径高比为２．２５．０条件下，吸附柱具备适宜的生产周期，连续吸附操作可行，柱效率可达７５．９％；在温度为１５℃、采用２ｍｏｌ／Ｌ稀盐酸作脱附剂，过柱速率为５．０ｍＬ／ｍｉｎ的条件下，吸附剂易于脱附再生，脱附效率可达７８．１％     

Enhanced struvite recovery from wastewater using a novel cone-inserted fluidized bed reactor

The feasibility of struvite recovery at low （12.5 mg/L） and high （120 mg[L） phosphorus concentrations was studied by constructing a novel fluidized bed reactor with cones （FBRwc） and without cones （FBRwoc）. The crystallization process was continuously operated for 133 days under different hydraulic retention times （HRT = 1-10 hr）, pH （7.5-10）, and molar ratios of Mg/P （0.75-1.75）, N/P （1-10） and Ca/Mg （0-2）. The optimum operating conditions of HRT, pH, Mg/P and N/P molar ratios were found to be 2 hr, 9, 1.25, and 7.5, respectively. Under these optimum conditions, the phosphorus precipitation efficiencies of FBRwc were 93% for low and 98% for high phosphorus influent; however, the efficiencies were 78% and 81% for FBRwoc, respectively. Due to crystal losses at each junction （17%-31%）, the crystal recovery efficiency of FBRwoc was relatively low （47%-65%） for both influent concentrations. However, the losses were minimal in FBRwc, which showed 75% and 92% crystal recovery for low and high phosphorus concentrations, respectively. At low calcium concentration, crystal chemical analysis showed the product to be pure struvite （〉 99%）. The scanning electron microscope and X-ray diffraction results further confirmed that the crystal recovered from FBRwc contained pure struvite, which could be considered a high quality fertilizer. Except HRT, all parameters （pH, Mg/P, N/P and Ca/Mg） were found to be influencing factors for FBRwc performance. Overall, inserting cones in each part of the reactor played a significant role in enhancing struvite recovery from a wide range of phosphorus-containing wastewater.     

Turbosorp湍流吸收循环流化床烟气脱硫技术在改造工程中的应用

循环流化床半干法烟气脱硫技术是目前世界上主流脱硫工艺技术之一,主要适用于大中型燃煤电厂的烟气脱硫,在国内外拥有大量成功运行的工程案例。本文章基于本公司实践论述Turbosorp湍流吸收循环流化床脱硫技术的技术特点、关键工艺控制要点以及在机组改造工程中的技术优势,为同类型机组改造工程中的方案选择提供参考。     

Emissions of SO2, NO and N2O in a circulating fluidized bed combustor during co-firing coal and biomass

This paper presents the experimental investigations of the emissions of SO2, NO and N2O in a bench scale circulating fluidized bed combustor for coal combustion and co-firing coal and biomass. The thermal capacity of the combustor is 30 kW. The setup is electrically heated during startup. The influence of the excess air, the degree of the air staging, the biomass share and the feeding position of the fuels on the emissions of SO2, NO and N2O were studied. The results showed that an increase in the biomass shares resulted in an increase of the CO concentration in the flue gas, probably due to the high volatile content of the biomass. In co-firing, the emission of SO2 increased with increasing biomass share slightly, however, non-linear increase relationship between SO2 emission and fuel sulfur content was observed. Air staging significantly decreased the NO emission without raising the SO2 level. Although the change of the fuel feeding position from riser to downer resulted in a decrease in the NO emission level, no obvious change was observed for the SO2 level. Taking the coal feeding position R as a reference, the relative NO emission could significantly decrease during co-firing coal and biomass when feeding fuel at position D and keeping the first stage stoichiometry greater than 0.95. The possible mechanisms of the sulfur and nitrogen chemistry at these conditions were discussed and the ways of simultaneous reduction of SO2, NO and N2O were proposed.     

生物流化床短程硝化的快速启动及影响因素研究

采用内循环生物流化床反应器处理模拟高浓度氨氮废水,以确定其对处理高浓度氨氮废水的可行性,同时对试验条件进行了优化。结果研究表明:控制温度为(31±1)℃,利用反应器自身流化所携带溶解的空气,反应器内DO值可维持在1.5~2.5 mg/L,调节pH为8.0~8.5。经过42 d的污泥驯化适应时期,进水氨氮(NH4+-N)浓度由50 mg/L提高到300 mg/L。由于流化床采用填料载体微生物膜与活性污泥双重作用,同时载体呈流化状态,接触均匀,有巨大的比表面积,可以使床内保持高浓度的生物量,从而达到高效快速的传质效果。在HRT由开始的16 h缩短到8 h的条件下,氨氮(NH4+-N)的去除率达到90%以上,亚硝氮(NO2--N)的积累率达到75%。且在以后30 d的稳定运行阶段,氨氮(NH4+-N)去除率和亚硝氮(NO2--N)积累率均保持稳定。同时反应器最后出水水质澄清,无需二沉池及污泥处理。