牛仔布染整废水处理技术及应用

以贵阳纺纱厂牛仔布生产车间废水处理工程为实例,介绍了“絮凝床-迷宫沉淀”技术对含靛兰染料、淀粉和PVC浆料的染整废水处理情况。经半年的工程实际运转表明,在进水污染物平均浓度：色度、SS、COD、BOD、NH3-N分别为400(稀释倍数)、97．0mg／L、821mg／L、189.51mg／L、1．8mg／L情况下,处理效果良好,其去除率分别为97．5％、97．4％、94．0％、90．0％、58．3％,出水达到了《纺织染整工业水污染物排放标准》(GB-4287-93)一级,符合环保要求,且可以回用于绿化、冲地坪等。该技术投资和运行费用合理,操作管理方便,适合中小型纺织印染厂废水处理。     

Experimental study on combustion characteristics of municipal solid waste

As incineration provides a relatively safe means of disposal, significant reduclaon ot welglat anti volume, ana energy recovery from the waste, it was adopted by many countries. For the experimental investigation on the combustion characteristics of municipal solid waste( MSW),a lab scale fluldized bed facility was constructed. Many kinds of combustion runs were conducted in this fluidized bed combustion facility. The examined parameters were bed temperature(773 to 1143K), form of fuels ( scrap or whole), moisture of fuels and so on. Concentration of CO2,CO,SO2, O2 and NOx in the flue gas were monitored and recorded every 5 seconds. The temperatttres along the reactor are recorded every 10 seconds. Experimental. results were given and analyzed.     

曝气-电解生态浮床的净化效果与机理分析

为强化生态浮床对重污染河道水体的净化能力,采用曝气-电解生态浮床联合技术增强生态浮床的净化功能.试验考察了电流密度、曝气量和处理时间对模拟的高氮磷重污染水体的净化潜力,分析了电解反应对填料细菌群落结构组成和浮床水生植物黄菖蒲（Iris pseudacorus）生长的影响.结果表明：在进水NH₃-N浓度为10 mg·L^-1,PO₄^3--P浓度为0.8 mg·L^-1,电流密度为0.74 mA·cm^-2,水力停留时间为3 d的条件下,相比于电解生态浮床和传统的生态浮床,曝气-电解生态浮床有利于水体中NH₃-N的去除（p<0.001）,其NH₃-N浓度下降至（0.92±0.24）mg·L^-1,而电解生态浮床处理的水体NH₃-N浓度为（6.85±0.17）mg·L^-1,传统生态浮床处理水体中NH₃-N浓度高达（8.09±0.40）mg·L^-1,曝气促进了水体中NH₃-N向NO₂^--N和NO₃^--N的转化.电解有利于水体中PO₄^3--P的去除,电解生态浮床处理水体中的PO₄^3--P浓度下降至（0.43±0.02）mg·L^-1,曝气-电解生态浮床处理的水体中PO₄^3--P下降至（0.46±0.02）mg·L^-1,可见,电解促进了PO₄^3--P的去除.从对I.pseudacorus生理生化指标变化分析可知,曝气有利于减弱电解反应对I.pseudacorus的损伤;对基质生物膜的16S rDNA分析可知,电解反应增加了浮床基质中自养反硝化微生物数量.因此,曝气-电解生态浮床是一种有效的净化重污染水体的方法.     

High efficiency chlorine removal from polyvinyl chloride (PVC) pyrolysis with a gas–liquid fluidized bed reactor

In this research a gas–liquid fluidized bed reactor was developed for removing chlorine (Cl) from polyvinyl chloride (PVC) to favor its pyrolysis treatment. In order to efficiently remove Cl within a limited time before extensive generation of hydrocarbon products, the gas–liquid fluidized bed reactor was running at 280–320 °C, where hot N₂ was used as fluidizing gas to fluidize the molten polymer, letting the molten polymer contact well with N₂ to release Cl in form of HCl. Experimental results showed that dechlorination efficiency is mainly temperature dependent and 300 °C is a proper reaction temperature for efficient dechlorination within a limited time duration and for prevention of extensive pyrolysis; under this temperature 99.5% of Cl removal efficiency can be obtained within reaction time around 1 min after melting is completed as the flow rate of N₂ gas was set around 0.47–0.85 Nm³ kg^?1 for the molten PVC. Larger N₂ flow rate and additives in PVC would enhance HCl release but did not change the final dechlorination efficiency; and excessive N₂ flow rate should be avoided for prevention of polymer entrainment. HCl is emitted from PVC granules or scraps at the mean time they started to melt and the melting stage should be taken into consideration when design the gas–liquid fluidized bed reactor for dechlorination.     

Thermal valorization of post-consumer film waste in a bubbling bed gasifier

The use of plastic bags and film packaging is very frequent in manifold sectors and film waste is usually present in different sources of municipal and industrial wastes. A significant part of it is not suitable for mechanical recycling but could be safely transformed into a valuable gas by means of thermal valorization. In this research, the gasification of film wastes has been experimentally investigated through experiments in a fluidized bed reactor of two reference polymers, polyethylene and polypropylene, and actual post-consumer film waste. After a complete experimental characterization of the three materials, several gasification experiments have been performed to analyze the influence of the fuel and of equivalence ratio on gas production and composition, on tar generation and on efficiency. The experiments prove that film waste and analogue polymer derived wastes can be successfully gasified in a fluidized bed reactor, yielding a gas with a higher heating value in a range from 3.6 to 5.6 MJ/m³ and cold gas efficiencies up to 60%.     

喷射床电沉积法处理含铜废水的试验研究

以实验室模拟含铜废水为研究对象,采用恒电流喷射床微粒电沉积法对其进行条件试验.结果表明,在pH=3.0、沉积液质量浓度为1 g/L、恒电流为10 A、阴极微粒粒径为1.8 mm、沉积液温度为20℃、鼓入氮气的条件下,铜离子的最大去除率为87.64％,平均电流效率可以达到81.53％,较同等条件下平板电极提高了63％.喷射床微粒电极采用的阴极微粒电极具有较大的比表面积,微粒的喷射循环能够有效地消除沉积过程中出现的浓差极化现象,鼓入氮气可以明显降低沉积液中的溶解氧浓度,从而抑制沉积的金属铜返溶,因此,喷射床微粒电沉积法在处理含铜废水时能够获得较高的电沉积率和电流效率.     

Can Rapid Assessment Protocols Be Used to Judge Sediment Impairment in Gravel‐Bed Streams? A Commentary

Land management agencies commonly use rapid assessments to evaluate the impairment of gravel‐bed streams by sediment inputs from anthropogenic sources. We question whether rapid assessment can be used to reliably judge sediment impairment at a site or in a region. Beyond the challenges of repeatable and accurate sampling, we argue that a single metric or protocol is unlikely to reveal causative relations because channel condition can result from multiple pathways, processes, and background controls. To address these concerns, a contextual analysis is needed to link affected resources, causal factors, and site history to reliably identify human influences. Contextual analysis is equivalent in principle to cumulative effects and watershed analyses and has a rich history, but has gradually been replaced by rapid assessment methods. Although the approaches differ, rapid assessment and contextual analysis are complementary and can be implemented in a two‐tiered approach in which rapid assessment provides a coarse (first‐tier) analysis to identify sites that deserve deeper contextual assessment (second‐tier). Contextual analysis is particularly appropriate for site‐specific studies that should be tailored to local conditions. A balance between rapid assessment and contextual analysis is needed to provide the most effective information for management decisions.     

Prediction of Total Sediment Load in Sand‐Bed Rivers in Korea Using Lateral Distribution Method

A new method for numerically predicting the total sediment load in a river is proposed. The method can be used to predict the total sediment load with information on channel geometry and slope, flow, and bed materials. The conventional method uses a 1D approach that assumes the channel has a wide rectangular shape. However, the proposed method computes depth‐averaged velocity over the width and predicts the total sediment load based on the flow computations. The new method, therefore, is expected to predict better if the flow changes significantly in the lateral direction. The proposed method was applied to three large sand‐bed rivers in Korea, where information is available regarding suspended sediment. Five formulas were tested of use in making total sediment load computations, namely Engelund‐Hansen's, Ackers‐White's, Yang's, Brownlie's, and Karim's formulas. The predicted total sediment loads are compared not only with measured data but also with results calculated using the 1D approach. Discrepancy ratios between the predicted and measured total sediment loads are given and the results are discussed.     

浮床栽培蕹菜根际脱氮微生物研究

浮床栽培植物是一种利用植物根系的吸收和根际微生物作用来改善水质的生物修复技术.本研究以温棚内浮床栽培蕹菜试验为基础,采用PFU法定期监测脱氮细菌变化情况,并与水中总氮含量进行对比,分析在浮床栽培植物情况下脱氮细菌的特征及其与水中总氮含量变化的关系,结果表明:1)栽培蕹菜有利于脱氮细菌的稳定生长;2)脱氮细菌的生长与总氮的去除有良好的相关性.研究为浮床栽培植物净化水质提供了理论依据,对该技术的推广应用有一定的理论和现实意义.表5,参10.     

人工浮床技术在污染水体生态修复中的研究

人工浮床作为一种有效、经济、新型的地表水生态修复技术,已被许多国家成功地应用于地表水的污染治理和生态修复中,成为目前水环境综合治理领域研究和应用的热点,主要依靠植物、微生物和水生动物的共同作用实现对水体的净化.概述了人工浮床国内外研究现状及其工程应用实例,对处理效果影响因素进行了分析,展望了发展前景.