氧化沟工艺污水处理厂的调试运行

以安徽某县污水处理厂的改良氧化沟工艺调试为例,采用自然培菌和间歇培养相接合的方式进行调试,结果表明方法可行。在进水COD100mg/L时,MLSS在1500mg/L时,出水COD、NH4-N均可取得较好的处理效果。同时对调试过程中的各环节如人员培训、带负荷试车、污泥培养等进行了详细阐述,并确定了各工艺段的控制参数。     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Reduction and characterization of bioaerosols in a wastewater treatment station via ventilation

Bioaerosols from wastewater treatment processes are a significant subgroup of atmospheric aerosols. In the present study,airborne microorganisms generated from a wastewater treatment station(WWTS) that uses an oxidation ditch process were diminished by ventilation.Conventional sampling and detection methods combined with cloning/sequencing techniques were applied to determine the groups,concentrations,size distributions,and species diversity of airborne microorganisms before and after ventilation. There were 3021 ± 537 CFU/m3 of airborne bacteria and 926 ± 132 CFU/m3 of airborne fungi present in the WWTS bioaerosol.Results showed that the ventilation reduced airborne microorganisms significantly compared to the air in the WWTS. Over 60% of airborne bacteria and airborne fungi could be reduced after4 hr of air exchange. The highest removal(92.1% for airborne bacteria and 89.1% for fungi) was achieved for 0.65–1.1 μm sized particles. The bioaerosol particles over 4.7 μm were also reduced effectively. Large particles tended to be lost by gravitational settling and small particles were generally carried away,which led to the relatively easy reduction of bioaerosol particles0.65–1.1 μm and over 4.7 μm in size. An obvious variation occurred in the structure of the bacterial communities when ventilation was applied to control the airborne microorganisms in enclosed spaces.     

Experimental study on filtration and continuous regeneration of a particulate filter system for heavy-duty diesel engines

This study investigated the filtration and continuous regeneration of a particulate filter system on an engine test bench, consisting of a diesel oxidation catalyst（DOC） and a catalyzed diesel particulate filter（CDPF）. Both the DOC and the CDPF led to a high conversion of NO to NO2 for continuous regeneration. The filtration efficiency on solid particle number（SPN） was close to100%. The post-CDPF particles were mainly in accumulation mode. The downstream SPN was sensitively influenced by the variation of the soot loading. This phenomenon provides a method for determining the balance point temperature by measuring the trend of SPN concentration.     

Fenton试剂氧化法处理印染废水实验研究

通过将Fenton法应用于印染废水的处理,研究pH值、温度、反应时间、Fe2+投加量以及H2O2投加量对Fenton试剂处理印染废水的影响,同时确定Fenton法处理印染废水的最适反应条件。实验结果表明:(1)最适反应条件,即pH值、温度、反应时间、Fe2+投加量、H2O2投加量分别为3,50℃,45 min,70 mg/L,2.5 mL/L,此时COD的去除率最高,为66.60%。(2)pH值为3时,下列因素对COD的去除率影响程度大小依次为H2O2投加量Fe2+投加量反应时间反应温度。     

普光气田含硫污水尾气处理工艺应用与优化

针对中国石化普光气田产出水属于典型的含硫污水,密闭处理系统中产生大量高含硫尾气,论述了尾气处理工艺中存在的问题,优化了单一的生物除硫、活性炭吸附工艺,增加了一级碱洗、氧化除硫工艺,实现尾气达标排放。     

活性炭催化过氧化氢去除荧光增白剂

研究了活性炭(activated carbon,AC)吸附、改性活性炭(activated carbon modified,ACM)吸附、过氧化氢(H2O2)氧化、AC催化H2O2等方法对水体中荧光增白剂VBL的处理效果,并通过自由基俘获剂叔丁醇、催化过程气体分析等探讨了AC催化H2O2分解VBL的机制.结果表明,经硝酸铁[Fe(NO3)3]改性过的ACM对VBL的吸附去除率高于未改性的AC.活性炭催化H2O2对VBL的去除效果明显,但未改性AC催化去除率高于ACM.60 min时,AC催化氧化去除率即可达到95%以上,而ACM仅为58%.叔丁醇的加入降低了AC和ACM催化氧化对VBL的去除率,表明AC催化H2O2氧化能促进H2O2形成羟基自由基(·OH)和原子氧参与反应.AC催化H2O2分解及释放气体分析表明,AC能催化H2O2形成氧气并放热,且ACM明显快于AC.结合催化H2O2去除VBL效率的结果分析,ACM催化反应时活性中间物(自由基和原子氧等)产生速率快于AC,活性中间物自身消耗形成氧气,而不是用于分解VBL.催化反应中活性中间产物的形成速率与反应物供给速率的不匹配可能是导致ACM催化效果弱于AC的重要原因.     

半短程亚硝化与厌氧氨氧化联合脱氮工艺微生物特征研究进展

半短程亚硝化-厌氧氨氧化脱氮技术具有良好的发展前景,该工艺的发展以及应用分子生物学技术对好氧氨氧化菌种群和厌氧氨氧化种群生态学的研究备受人们关注.本文综述了工艺原理和影响因子诸如温度、pH值、氧的可利用性、游离氨浓度等对氨氧化菌及厌氧氨氧化菌的影响,并介绍了应用分子生物学方法对氨氧化菌与厌氧氨氧化菌的类别及分布的研究结果,并对该工艺提出了展望.     

还原脱氯-生物联合降解2,4-二氯苯氧乙酸

采用Pd/Fe双金属对2,4-二氯苯氧乙酸(2,4-D)进行催化还原脱氯,以活性污泥对2,4-D脱氯产物进行生物氧化,考察初始pH、活性污泥量、污染物初始浓度、温度等因素对生物氧化的影响情况.通过PCR-变性梯度凝胶电泳分析污泥体系菌群变化情况,高效液相色谱测定来推测目标污染物的降解过程.结果表明:1 Pd/Fe双金属可有效还原2,4-D,其主要先还原为2-氯苯氧乙酸(2-CPA),最终顺序脱氯为苯氧乙酸(PA).2 2,4-D具有较大生物毒性,其脱氯产物毒性下降,更易被生物降解.3 pH=7、污泥量50 mL/200 mL、适量的初始PA浓度(14.6 mg·L-1)和30℃均有利于PA的去除.在该条件下反应96 h,PA去除率可达84.3%.     

双组分VOCs的催化氧化及动力学分析

考察了微波加热与管式炉加热下挥发性有机化合物(VOCs)甲苯与氯苯的催化氧化性能,并对双组分VOCs的反应动力学进行了分析.结果表明,VOCs的竞争吸附使得双组分中甲苯和氯苯的转化率比单组分降低3%~12%;微波的"热点效应"与"非热效应"使得VOCs转化效率明显优于管式炉加热,尤其是氯苯的转化率提高了31%~38%;微波加热降低了氧化反应温度和处理能耗.动力学分析表明,微波加热下甲苯和氯苯的反应活化能比管式炉加热下减少了2146 J·mol-1和1450J·mol-1,微波加热下氯苯的化学反应速率常数是管式炉加热的35倍,甲苯的反应速率常数提高了6倍.