Swine wastewater treatment in a two stage sequencing batch reactor using real‐time control

Abstract

A laboratory scale two‐stage sequencing batch reactor (TSSBR) was used to study the effectiveness of pH as a real‐time control parameter in swine wastewater treatment. A Ringlace media was inserted into the A/O (Anoxic/Oxic) reactor for bacteria immobilization. The TSSBR was subjected to three levels of organic loading. The pH and ORP (Oxidation Reduction Potential) patterns obtained were consistent with distinct features, enabling the real‐time control strategy to effectively set a flexible aeration time pending on influent concentration, hence resulting in flexible cycle time and HRT (Hydraulic Retention Time) for the system. The real‐time process ensured a removal efficiency of over 99% and 95%, respectively, for ammonia and TOC (Total Organic Carbon). For NO₃ ^‐‐N and PO₄ ^‐3, the run with influent TOC = 4,000 mg/L yielded the most efficient removal of 61% and 95%, respectively. Test results suggest that pH can be a viable tool for on‐line real‐time control of a biological treatment process.     

粗苯污染事故应急处理

针对一次苯泄漏事故的应急处理过程、方法进行论述与总结，并分析了事故现场周围地表、地下水中苯污染浓度的变化情况，提出了该类事故的应急措施，以此作为处理同类事故的参考和依据。     

新疆番茄酱企业生产废水处理利用方式探析

近年来,新疆番茄酱加工业得到了迅速发展,目前番茄酱的产销量已占全国的90%以上。与此同时,新疆番茄酱生产企业的废水排放量也大幅增加,大量未经处理的废水直接排放,已对当地的水环境构成严重的污染隐患。本文分析了新疆番茄酱企业生产废水的排放特征与目前排放出路的可行性,并结合新疆的自然地理条件及番茄酱企业的分布情况,着重探讨了土地处理这一适合新疆的废水利用方式,以期有利于新疆的环境保护和废水资源的循环利用。     

Fruit Stones from Industrial Waste for the Removal of Lead Ions from Polluted Water

Lead, one of the earliest metals recognized and used by humans, has a long history of beneficial use. However, it is now recognized as toxic and as posing a widespread threat to humans and wildlife. Treatment of lead from polluted water and wastewater has received a great deal of attention. Adsorption is one of the most common technologies for the treatment of lead-polluted water. This technique was evaluated here, with the goal of identifying innovative, low-cost adsorbent. This study presents experiments undertaken to determine the suitable conditions for the use of peach and apricot stones, produced from food industries as solid waste, as adsorbents for the removal of lead from aqueous solution. Chemical stability of adsorbents, effect of pH, adsorbents dose, adsorption time and equilibrium concentration were studied. The results reveal that adsorption of lead ions onto peach stone was stronger than onto apricot stone up to 3.36% at 3 h adsorption time. Suitable equilibrium time for the adsorption was 3–5 h (% Pb adsorption 93% for apricot and 97.64% for peach). The effective adsorption range for pH in the range was 7–8. Application of Langmuir and Freundlich isotherm models show high adsorption maximum and binding energies for using these adsorbents for the removal of lead ions from contaminated water and wastewater.     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

Multi-response optimization of Fenton process for applicability assessment in landfill leachate treatment

Fenton process, as a pretreatment method, was found to be effective in the primary treatment of mature/medium landfill leachate. However, the main problem of the process is the large amount of produced sludge that requires an accurate feasibility evaluation for operational applications. In this study, the response surface methodology was applied for the modeling and optimization of Fenton process in three target responses, (1) overall COD removal, (2) sludge to iron ratio (SIR) and (3) organics removal to sludge ratio (ORSR), where the latter two were new self-defined responses for prediction of sludge generation and applicability assessment of the process, respectively. The effective variables included the initial pH, [H₂O₂]/[Fe²⁺] ratio and Fe²⁺ dosage. According to the statistical analysis, all the proposed models were adequate (with adjusted R² of 0.9116–0.9512) and had considerable predictive capability (with prediction R² up to 0.9092 and appropriate adequate precision). It was found that all the variables had significant effects on the responses, specifically by their observed role in dominant oxidation mechanism. The optimum operational conditions obtained by overlay plot, were found to be initial pH of 5.7, [H₂O₂]/[Fe²⁺] ratio of 17.72 and [Fe²⁺] of 195 mM, which led to 69% COD removal, 2.4 (l sludge/consumed mole Fe²⁺) of SIR and 16.5 (gCOD removed/l produced sludge) for ORSR in verification test, in accordance with models-predicted values. Finally, it was observed that [H₂O₂]/[Fe²⁺] ratio and Fe²⁺ dosage had significant influence on COD removal, while Fe²⁺ dosage and [H₂O₂]/[Fe²⁺] ratio had remarkable effects on SIR and ORSR responses, respectively.     

粘胶化纤厂废气治理试验

采用ＴＦ－ＴＡ工艺治理粘胶化纤厂废气。先以ＴＦ脱硫液选择脱除ＨＺＳ,再以ＴＡ液体脱除ＣＳ２。Ｈ２Ｓ脱除和再生能一步完成,脱除率９８％以上,其表达ηＨ２ｓ＝９９．５＋４．７１×１０－４ｘ－３．６８×１０－７ｘ２。ＣＳ２脱除率在气液比２００—３００时达８０％─９０％,其表达式：ηＣＳ２＝９８．９－１．３２×１０－３ｘ—２．００×１０－４ｘ２。文中还讨论了粘胶化纤厂废气总体治理意见。     

我区城市污水处理程度探讨

建立城市污水处理厂处理污水,是城市发展的必然趋势,而处理级别及处理后水的去向及用途是关系到环境保护和资源得到充分利用的关键,针对我区干旱缺水,灌溉农业特征及天然水域的特点,就污水处理级别排水的用途提出一些看法。     

Sustainable options of post treatment of UASB effluent treating sewage: A review

The upflow anaerobic sludge blanket (UASB) process is reported to be a sustainable technology for domestic wastewaters treatment in developing countries and for small communities. However, the inability of UASB process to meet the desired disposal standards has given enough impetus for subsequent post treatment. In order to upgrade the UASB based sewage treatment plants (STPs) to achieve desired effluent quality for disposal or for reuse, various technological options are available and broadly differentiated as primary post-treatment for the removal of organic and inorganic compounds and suspended matter; secondary post-treatment for the removal of hardly degradable soluble matter, colloidal and nutrients; and polishing systems for removals of pathogens. Hence, this paper discusses the different systems for the treatment of UASB reactor effluent treating sewage. Additionally, a comparative review, an economic evaluation of some of the emerging options was conducted and based on the extensive review of different integrated combination, i.e. UASB-different aerobic systems, a treatment concept based on natural biological mineralization route recognized as an advanced technology to meet all practical aspects to make it a sustainable for environmental protection, resource preservation and recovering maximum resources.