反应气耦合等离子体降解沙林模拟剂

采用水蒸气、氨气、过氧化氢气雾和臭氧4种气体对沙林模拟剂氟磷酸二异丙酯(DFP)进行降解研究,发现臭氧对DFP具有较好的降解作用,在流量200 L/h,DFP初始浓度50 mg/m3时,降解率最高可达56.1%。对高浓度DFP(大于80 mg/m3)进行降解研究时,等离子体单独作用最高降解率为89%,而添加臭氧后的降解率都在95%以上。计算得到臭氧作用的能量利用率为0.05 mg/(W·h),等离子体的能量利用率为0.55 mg/(W·h),而添加臭氧后的等离子体能量利用率为0.68 mg/(W·h)明显高于臭氧和等离子体能量利用率之和,因此对高浓度DFP进行处理时,臭氧与等离子体存在耦合作用。对等离子体和臭氧耦合等离子体降解DFP反应进行了产物分析,发现主要的降解产物基本一致,但是臭氧的存在能使降解更加彻底。     

交叉上市公司社会责任缺陷披露的市场反应——基于紫金矿业突发渗漏环保事故的案例研究

伴随着工业化进程加快,社会责任缺失现象日益严重,各类企业违法违规事故层出不穷,其中不乏国有大型控股公司,这种现象引起了投资者、监管机构等利益相关者的广泛关注。在此背景下,研究资本市场对上市公司社会责任缺陷披露的反应具有重要的理论意义和现实意义。本文以交叉上市的紫金矿业为例,采用事项研究法,检验了A股和H股市场对紫金矿业集团股份有限公司发布的一系列有关紫金山铜矿湿法厂污水池突发渗漏环保事故重要公告的市场反应,并比较了两地市场对同一公告的反应差异。研究发现:两地市场对重大事故公告均提前预知并呈负面反应,在公告前A股市场反应程度大于H股市场,公告发布后H股市场投资者更加敏感;两地市场对董事会(临时)决议公告呈正面反应,但H股市场投资者更加谨慎;对处罚公告两市反应不同,A股市场未对处罚公告作出反应,H股市场对处罚公告呈负面反应;总体而言,H股市场与A股市场反应程度存在显著差异。     

Dechlorination of PCBs in the simulative transformer oil by microwave-hydrothermal reaction with zero-valent iron involved

The conventional hydrothermal reaction with iron powder, NaOH and H₂O as reactants was reported to occur at temperature above 423 K, and iron oxides (Fe₃O₄ and NaFeO₂) and hydrogen were produced. In this study, microwave heating was adopted to take the place of conventional heating to induce the hydrothermal reaction. Under microwave irradiation, NaOH and H₂O absorbed microwave energy by space charge polarization and dipolar polarization and instantly converted it into thermal energy, which initiated the hydrothermal reaction that involved with zero-valent iron. X-ray diffraction (XRD) analysis found Fe₃O₄/NaFeO₂ and confirmed the occurrence of microwave-induced hydrothermal reaction. The developed microwave-hydrothermal reaction was employed for the dechlorination of PCBs. Hexadecane containing 100 mg L⁻¹ of Aroclor1254 was used as simulative transformer oil, and the dechlorination of PCBs was evaluated by GC/ECD, GC/MS and ion chromatography. For PCBs in 10 mL simulative transformer oil, almost complete dechlorination was achieved by 750 W microwave irradiation for 10 min, with 0.3 g iron powder, 0.3 g NaOH and 0.6 mL H₂O added. The effects of important factors including microwave power and the amounts of reactants added, on the dechlorination degree were investigated, moreover, the dechlorination mechanism was suggested. Microwave irradiation combined with the common and cheap materials, iron powder, NaOH and H₂O, might provide a fast and cost-effective method for the treatment of PCBs-containing wastes.     

Bromination of selected pharmaceuticals in water matrices

The bromination of five selected pharmaceuticals (metoprolol, naproxen, amoxicillin, phenacetin, and hydrochlorothiazide) was studied with these compounds individually dissolved in ultra-pure water. The apparent rate constants for the bromination reaction were determined as a function of the pH, obtaining the sequence amoxicillin > naproxen ? hydrochlorothiazide ≈ phenacetin ≈ metoprolol. A kinetic mechanism specifying the dissociation reactions and the species formed for each compound according to its pK_a value and the pH allowed the intrinsic rate constants to be determined for each elementary reaction. There was fairly good agreement between the experimental and calculated values of the apparent rate constants, confirming the goodness of the proposed reaction mechanism.In a second stage, the bromination of the selected pharmaceuticals simultaneously dissolved in three water matrices (a groundwater, a surface water from a public reservoir, and a secondary effluent from a WWTP) was investigated. The pharmaceutical elimination trend agreed with the previously determined rate constants. The influence of the main operating conditions (pH, initial bromine dose, and characteristics of the water matrix) on the degradation of the pharmaceuticals was established. An elimination concentration profile for each pharmaceutical in the water matrices was proposed based on the use of the previously evaluated apparent rate constants, and the theoretical results agreed satisfactorily with experiment. Finally, chlorination experiments performed in the presence of bromide showed that low bromide concentrations slightly accelerate the oxidation of the selected pharmaceuticals during chlorine disinfection.     

O3氧化结合化学吸收同时脱硫脱硝的动力学及热力学研究

构建了O3氧化多种污染物的反应机制,并对O3氧化SOx、NOx过程进行动力学模拟,然后利用热力学原理计算出Ca(OH)2和CaCO3湿法烟气同时脱硫脱硝吸收反应达到平衡时SOx和NOx的分压力.结果表明,Ca(OH)2作吸收剂湿法烟气同时脱硫脱硝比CaCO3作吸收剂效果好,而且两者几乎100％地去除烟气中的SOx和NO...     

超声波-铁粉协同降解五氯酚

通过超声波-铁粉联合体系协同降解废水中的五氯酚(PCP).实验结果表明:降解120 min后,PCP去除率可达90.4％;在该体系中铁粉被逐渐腐蚀成Fe2+,随降解时间的延长,Fe2+浓度逐渐增加;体系中的Fe2+可以促进·OH的产生,并且可以与超声空化作用下产生的H2O2发生Fenton试剂氧化反应降解PCP;超声波...     

锐钛矿-金红石混合晶型TiO2降解气相苯

用溶胶-凝胶法并通过控制煅烧温度合成不同晶相比的混合晶型纳米TiO_2,在紫外光光照下降解气相苯。考察了苯初始质量浓度、紫外灯光照强度和催化剂加入量对苯去除率的影响;探究了光催化降解气相苯的动力学特征。结果表明:450℃煅烧制备的催化剂降解苯效率最高,此催化剂金红石相质量分数为6.30%;在苯初始质量浓度为74.39 mg/m~3、催化剂加入量为7 g、光照强度为2.18 klux的最佳条件下反应84 min,苯去除率达99.73%;光催化降解率与光照强度之间符合0.5级动力学特征;当催化剂加入量为3 g时,单位时间单位质量催化剂降解苯的质量最多;苯的光催化降解反应均符合一级动力学方程。     

壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B动力学研究

采用仿生矿化法制备了壳聚糖/纳米CdS复合颗粒光催化剂,并用于可见光光催化降解猩红B染料模拟废水,研究了猩红B初始浓度、pH、催化剂投加量和催化剂重复使用次数等因素对猩红B光催化降解的影响.X射线衍射(XRD)分析表明,壳聚糖能有效负载CdS纳米微晶.采用Langmuir-Hinshelwood模型描述壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B反应动力学行为,在猩红B初始质量浓度较低(≤20 mg/L)时,光催化降解过程符合假一级动力学方程.降低猩红B初始浓度和溶液pH都可显著增大光催化降解速率常数;催化剂投加量小于0.7 g/L时,光催化降解速率随其增加而增大,但催化剂投加量过大会使光催化降解速率减小;催化剂重复使用第5次时,猩红B光催化降解速率常数仍为第1次使用时的63.4%.     

高锰酸钾降解地下水中PCE的研究

以氯代有机污染物中常见的PCE为目标污染物,以自制高锰酸钾溶液为氧化剂,采用批实验方法,探讨了高锰酸钾降解PCE的反应动力学、影响因素以及反应机理。反应结果表明,高锰酸钾降解PCE的反应符合一级动力学方程,反应活化能E为57.119 kJ/mol,在30℃条件下,反应速率常数为0.0076 min^-1,半衰期为91.20 min。在pH在3～10,离子强度在0～0.1030 mol/L之间变化时,反应速率不受明显影响。     

Removal of arsenic from wastewater using iron compound: Comparing two different types of adsorbents in the context of LCA

A study was carried out in order to compare the environmental performance of two different types of adsorbents in removing arsenic (As) from wastewater. A FeCl₃-based adsorbent and a poly-Fe-based adsorbent were first synthesized and their abilities in adsorbing As from wastewater were investigated in terms of the adsorption density and the rate of adsorption. Here, it should be noted that the main material being used in the synthesis of the poly-Fe-based adsorbent was a waste product, known as polyferric sulfate or poly-Fe in short, which exits the manufacturing process of titanium dioxide.Both adsorbents were then compared in the context of life-cycle assessment (LCA). In other words, the experimental results (i.e. the value of the adsorption density and the rate of adsorption) were input into the LCA model in order to assess the environmental performance of each adsorbent in removing arsenic. An estimate for the environmental burden of each option was finally calculated as the sum of the depletion of abiotic resources (ADP), the global warming potential (GWP), the acidification potential (AP), the photo-oxidant formation potential (POCP), the eutrophication potential (EP), and the human toxicity potential (HTP). The main finding of this study was that the adsorption of arsenic by using the poly-Fe-based adsorbent is more attractive treatment option in the environmental protection point of view than the adsorption by using the FeCl₃-based adsorbent, which generates a relatively larger environmental burden.