剩余污泥热水溶性有机物的提取方法优化研究

热水溶性有机物含量和组成是表征剩余污泥(简称为污泥)中有机质生物可利用性的重要手段.分析了不同热水淬时间(1~24h)和不同ρ(污泥)(0.7~36.0g/L)对热水溶性蛋白质和碳水化合物等溶出的影响,据此对剩余污泥中热水溶性有机物的提取方法进行了优化. 结果表明:污泥在60℃水淬8h时,水溶性蛋白质和碳水化合物的溶出率达到最大,分别为34.6%和36.1%;但是,随着水淬时间的延长,部分蛋白质被转化成氨氮,部分碳水化合物也发生了转化和降解,致使二者的浓度降低. 考虑测试分析的时间效率和溶出率稳定性,污泥热水溶性有机物最优水淬时间建议设置为5h. 研究结果表明,热水溶性有机物的溶出率随ρ(污泥)降低呈升高趋势,当ρ(污泥)为0.7g/L时,热水淬5h后蛋白质和碳水化合物的溶出率最大,二者分别为52.9%和36.6%.      

污泥浓度对双重后置反硝化工艺脱氮除磷的影响

利用城市实际污水考察了ρ(MLSS)在2 400、3 350、4 300和5 250 mg/L 4种工况下SBR反应器(厌氧/好氧/缺氧/再好氧/沉淀/排水/预缺氧运行模式)的脱氮除磷效果,并分析了反应器单个周期内有机物、氮和磷的转化过程及污泥产量. 结果表明:ρ(MLSS)由2 400 mg/L升至5 250 mg/L时,系统TN去除率由52.5%升至66.6%;后续缺氧及预缺氧工序的脱氮比例(该工序TN去除量占系统TN总去除量的比例)由12.7%增至23.1%;ρ(MLSS)为4 300 mg/L时系统TP去除率(75.6%)达到最大. 后续缺氧及预缺氧工序中,ρ(MLSS)与内源反硝化速率呈正相关(R2=0.703 7);提高ρ(MLSS)可使PAOs(聚磷菌)在下一个周期内获得更多的碳源,使厌氧释磷量由1.62 mg/L升至9.10 mg/L,但PAOs吸磷动力会减弱,对除磷不利. 在后置反硝化、污泥衰减、能量解偶联等减量机制共同作用下,ρ(MLSS)为4 300 mg/L时系统污泥减量可提高24.4%. 从脱氮除磷及污泥减量效果综合考虑,ρ(MLSS)是双重后置反硝化工艺重要的控制参数,在该研究条件下控制在4 300 mg/L最优.      

Effects of dissolved organic matter on the desorption of Cd in freeze–thaw treated Cd-contaminated soils

Lab-scale experiments were conducted to investigate the effects of dissolved organic matter (DOM) on the desorption of Cd in freeze–thaw treated Cd-contaminated soils. The results indicated that DOM significantly facilitated the desorption of Cd from freeze–thaw treated soils when comparing with that of non-frozen soils. Effects of DOM on the Cd desorption were highly dependent on the soil type and contamination concentration. The maximum desorption ratios of Cd by DOM generated from straw and sludge were 15.6% and 13.65%, respectively, in brown soils, and the maximum desorption ratios reached 14.7% and 9.3%, respectively, when using black soils through the same treatment. The higher the Cd contamination concentration in soils, the higher the ratio of Cd desorption by DOM. This was because of the integrated effects of the soil properties changed by the freeze–thaw treatment and the species transformation of Cd. The characteristics of DOM, such as its concentration and properties, had shown obvious impacts on the Cd desorption by DOM. The desorption was promoted with the increased DOM concentration and the hydrophilic fraction, and lowered pH and the low-molecular-weight of DOM.     

几种捕集高比电阻粉尘的电收尘器的机理

详细论述了影响电收尘器收尘效率的主要因素,指出常规电收尘器在捕集高比电阻粉尘时产生反晕现象,从而使收尘效率大大降低,并且提出几种适用于捕集高比电阻粉尘的电除尘结构,对开发新型电收尘器有一定的指导作用。     

硫酸铝渣和硫铁矿烧渣制聚硅酸硫酸铁的研究

研究硫酸铝渣和硫铁矿烧渣制聚硅酸硫酸铁的工艺流程及其主要参数.提取硫酸铝渣中的SiO2得到Na2SiO3溶液,提取硫铁矿烧渣中铁得到FeSO4结晶.用FeSO4结晶制备聚合硫酸铁.用含3.5% SiO2的Na2SiO3溶液,控制pH=4.0,制得聚硅酸,将聚合硫酸铁加入聚硅酸制得聚硅酸硫酸铁絮凝剂.红外光谱分析表明,聚硅酸硫酸铁结合了SO2-4.检测了聚硅酸硫酸铁对模拟浊水和垃圾填埋场渗滤液的絮凝效果,用铁和硅物质的量比为0.5、用量0.5 mL/L的聚硅酸硫酸铁,处理模拟浊水,除浊率可达90%以上.用铁和硅物质的量比为1.5、用量4.0 mL/L的聚硅酸硫酸铁处理垃圾填埋场渗滤液生化处理尾水,CODCr去除率可达60%.     

轧钢污泥综合利用的技术研究

阐述了一种轧钢污泥的回收处理技术,该技术可把轧钢污泥有效地分离成氧化铁粉和混合油,实现综合利用,减少铁素资源浪费,有良好的经济效益和环境效益.     

磁性载体生物膜反应器处理生活污水的试验研究

选取天然多孔矿物-浮石、网络状塑料外壳、磁铁为材料,开发出一种新型磁性载体,并将该载体应用于生物膜反应器中进行废水处理试验,结果表明:该磁性载体生物膜反应器在载体的挂膜性能及主要污染物去除功能上均优于非磁性载体生物膜反应器.磁性载体可在5d内完成挂膜,而非磁性载体则需8d,磁性载体生物膜反应器对COD、NH+ 4-N的去除率比非载体生物膜反应器分别高出5%和20%左右.在载体中心磁场强度为200Gs,水中溶解氧DO为2.0~3.5mg/L,水力停留时间HRT为5h的条件下,校园生活污水经磁性载体生物膜反应器处理后,出水中COD稳定在20mg/L左右, NH4+-N在5mg/L以下,两者的去除率均在90%左右,出水总氮为15mg/L,去除率在50%以上.实验结果还表明:连续运行60d后,磁性载体反应器内的生物膜量和悬浮污泥量仅为非磁性载体反应器的70%,说明磁场的存在有利于污泥减量化.磁载体生物膜反应器中载体外表面附着污泥及生物膜的SOUR值均大于非磁载体生物膜反应器,表明一定的磁场强度可以提高微生物活性.     

Continuous biohydrogen production from diluted molasses in an anaerobic contact reactor

An anaerobic contact reactor (ACR) system comprising a continuous flow stirred tank reactor (CSTR) with settler to decouple the hydraulic retention time (HRT) from solids retention time (SRT) was developed for fermentative hydrogen production from diluted molasses by mixed microbial cultures. The ACR was operated at various volumetric loading rates (VLRs) of 20–44 kgCOD·m^-3·d^-1 with constant HRT of 6 h under mesophilic conditions of 35°C. The SRT was maintained at about 46–50 h in the system. At the initial VLR of 20 kgCOD·m^-3·d^-1, the hydrogen production rate dropped from 22.6 to 1.58 L·d^-1 as the hydrogen was consumed by the hydrogentrophic methanogen. After increasing the VLR to 28 kgCOD·m^-3·d^-1 and discharging the sludge for 6 consecutive times, the hydrogentrophic methanogens were eliminated, and the hydrogen content reached 36.4%. As the VLR was increased to 44 kgCOD·m^-3·d^-1, the hydrogen production rate and hydrogen yield increased to 42.1 L·d^-1 and 1.40 mol H₂·molglucose-consumed^-1, respectively. The results showed that a stable ethanol-type fermentation that favored hydrogen production in the reactor was thus established with the sludge loading rate (SLR) of 2.0–2.5 kgCOD·kgMLVSS^-1·d^-1. It was found that the ethanol increased more than other liquid fermentation products, and the ethanol/acetic acid (mol/mol) ratio increased from 1.27 to 2.45 when the VLR increased from 28 to 44 kgCOD·m^-3·d^-1, whereas the hydrogen composition decreased from 40.4% to 36.4%. The results suggested that the anaerobic contact reactor was a promising bioprocess for fermentative hydrogen production.     

Co-fermentation of waste activated sludge with food waste for short-chain fatty acids production: effect of pH at ambient temperature

Effect of pH ranging from 4.0 to 11.0 on co-fermentation of waste activated sludge (WAS) with food waste for short-chain fatty acids (SCFAs) production at ambient temperature was investigated in this study. Experimental results showed that the addition of food waste significantly improved the performance of WAS fermentation system, which resulted in the increases of SCFAs production and substrate reduction. The SCFAs production at pH 6.0, 7.0, 8.0, and 9.0 and fermentation time of 4 d was respectively 5022.7, 6540.5, 8236.6, and 7911.7 mg COD·L^-1, whereas in the blank tests (no pH adjustment, pH 8.0 (blank test 1), no food waste addition, pH 8.0 (blank test 2), and no WAS addition (blank test 3)) it was only 1006.9, 971.1, and 1468.5 mg COD·L^-1, respectively. The composition of SCFAs at pH from 6.0 to 9.0 was also different from other conditions and propionic acid was the most prevalent SCFA, which was followed by acetic and n-butyric acids, while acetic acid was the top product under other conditions. At pH 8.0 a higher volatile suspended solids (VSS) reduction of 16.6% for the mixture of WAS and food waste than the sole WAS indicated a synergistic effect existing in fermentation system with WAS and food waste. The influence of pH on the variations of nutrient content was also studied during anaerobic fermentation of the mixture of WAS and food waste at different pH conditions. The release of NH4+-N increased with fermentation time at all pH values investigated except 4.0, 5.0 and in blank test one. The concentrations of soluble phosphorus at acidic pHs and in the blank test one were higher than those obtained at alkaline pHs. Ammonia and phosphorus need to be removed before the SCFAs-enriched fermentation liquid from WAS and food waste was used as the carbon source.     

The correlation of total and extractable heavy metals from soil and domestic sewage sludge and their transfer to maize ( Zea mays L.) plants

A study to understand the mobility and transport of heavy metals (HMs) from soil and soil amended with sewage sludge to maize plants was carried out. The total and ethylenediaminetetraaceticacid (EDTA)-extractable HMs in agricultural soil and untreated domestic sewage sludge samples, and the correlation between the total and extractable metals in soil and sewage sludge were carried out. Pot experiments were performed to study the transfer of HMs to maize grains, grown in soil (control) and in soil amended with sewage sludge (test samples). The total and extractable HMs in soil, sewage sludge, and maize grains were analysed by FAAS/ETAAS (flame atomic absorption spectrometer/electrothermal atomic absorption spectrometer) after digestion in microwave oven. Statistically significant correlations were obtained between the total contents of Cu, Cd, As and their respective extractable fractions in soil, while in domestic wastewater sludge (DWS) the better correlation was observed only for Ni and Cd. The edible part of maize plants (grains) from test samples presented high concentration of Zn, Pb, Ni, Cd, Cu, As, and Cr concentrations (80.7–85.6, 3.8–3.95, 2.35–2.5, 0.75–0.82, 3.21–3.29, 0.23–0.27, and 0.22–0.29?mg?kg^?1, respectively). Good correlations were found between metals in exchangeable fractions of both soil and DWS and total metals in control and test samples of maize grains. The transfer factor of all HMs from DWS to maize grains was also determined.