二氧化氯催化氧化处理直接大红染料

研究了ClO2化学氧化体系和ClO2催化氧化体系。实验结果表明:单用ClO2化学氧化处理COD为3 400mg/L的直接大红染料配制废水时,最佳反应pH值为1,氧化剂ClO2经济用量为400 mg/L废水,反应时间为10 min,COD去除率可达85.9%,氧化指数(COD削减量∶ClO2投加量)=7。当ClO2与自制催化剂所组成的催化氧化体系用于对直接大红染料配制废水的处理时,最佳反应pH值为2左右,氧化剂ClO2经济用量为600 mg/L废水,反应时间为6 min,COD去除率可达96.6%,氧化指数=6。结果表明,ClO2催化氧化法是一种新型高效的处理难降解废水的技术,有着广阔的应用前景。     

Landfill leachate treatment methods: A review

Landfilling of municipal waste is still a major issue of the waste management system in Europe. The generated leachate must be appropriately treated before being discharged into the environment. Technologies meant for leachate treatment can be classified as follows (i) biological methods, (ii) chemical and physical methods. Here we review briefly the main processes currently used for the landfill leachates treatments.     

沿面放电氧化液相亚硫酸铵

为了解决湿式氨法烟气脱硫生成不稳定亚硫酸铵（（NH4）2SO3）副产物的问题,设计了以不锈钢弹簧和溶液分别作为高压和低压电极的沿面放电系统,对液相（NH4）2SO3的氧化进行了研究。空气从反应器上方进入后经放电区域形成活性物质,再由底部的曝气头鼓入溶液并与（NH4）2SO3发生反应。比较了沿面放电处理与传统曝气处理的氧化效率,考察了放电电压、载气气量和初始浓度等因素对（NH4）2SO3氧化的影响。结果表明,沿面放电对（NH4）2SO3有显著的氧化效果;优化条件下的（NH4）2SO3氧化率接近100%;溶液中（NH4）2SO4与（NH4）2SO3的浓度比小于1时有利于（NH4）2SO3的氧化。     

深型地下土壤渗滤系统中氮的去除途径

为了系统研究氮在深型地下土壤渗滤系统中的去除途径,本次实验采用直径30cm,高200cm的有机玻璃柱模拟地下土壤渗滤系统;柱内分层装填取自北京顺义的土壤。在水力负荷为8cm／d的条件下,取得了较好的脱氮效果;氨氮去除率为99．80％;TN去除率为83．68％。通过观察氮沿土柱深度的变化规律发现,在1．30m以上的区域随着氨氮浓度的降低硝氮浓度逐渐增大,同时总氮浓度也在不断降低,约有30．55％在此区域被去除;通过氮元素质量平衡证明这部分氮是通过厌氧氨氧化反应去除的。在1．30m以下反硝化反应是脱氮的主要途径,在此过程中难降解有机物被利用。     

CNTs/TiO2/CS光降解苯的动力学

综合光催化氧化苯的动力学过程、光辐射场模型和质量守恒定律,采用平板型反应器建立了碳纳米管/二氧化钛/壳聚糖(CNTs/TiO2/CS)催化薄膜光催化氧化气相苯的数学模型;该模型考虑了光强、相对湿度、初始浓度与气体流速对气相苯光降解的影响。结果表明,建立的数学模型与实验结果吻合较好。     

Fenton氧化水中间氯硝基苯的动力学与机制研究

结合Fenton氧化反应动力学模型研究了Fenton氧化水中间氯硝基苯(m-ClNB)的影响因素和降解机制.结果表明:(1)反应初始pH、H2O2浓度、Fe2+浓度、污染物初始浓度和反应温度对m-ClNB的降解均有明显影响.在反应初始pH为3.5、m-ClNB初始摩尔浓度为0.444mmol/L、H2O2摩尔浓度为21.55mmol/L、Fe2+摩尔浓度为0.054mmol/L、反应温度为(25土1)℃的条件下,m-ClNB的去除效果较好.(2)建立了Fenton氧化m-ClNB的准一级反应动力学模型,且m-ClNB的降解与该模型拟合良好.基于不同反应温度时的准一级反应速率常数(kap),得到了m-ClNB降解的阿累尼乌斯公式,且活化能为36.51kJ/mol.(3)气相色谱(GC)/质谱(MS)和高效液相色谱(HPLC)/MS分析表明,Fenton氧化m-ClNB的主要产物有4-氯-2-硝基苯酚及其同分异构体、羟基乙酸、草酸、丁二酸、丙二酸、6-氯己酸、乙醛酸、2,2-二羟基丙二酸和2-乙基丙二酸等.     

城市污水条件下ASBR厌氧氨氧化的启动与脱氮性能

采用ASBR在城市污水条件下进行厌氧氨氧化的启动与脱氮性能研究。实验接种好氧硝化污泥,在温度为(35±1)℃、HRT为24 h、pH为7.3～8.5的条件下经过130 d的培养,成功启动了厌氧氨氧化反应。实验结果表明,厌氧氨氧化反应稳定运行时,TN容积负荷平均为0.179 kg/(m3.d),NH4+-N、NO2--N和TN去除率分别达到了95.30%、91.30%和76.28%。启动期和稳定运行期NH4+-N、NO2--N去除量和NO3--N生成量的比值分别达到1∶1.54∶0.25和1∶1.27∶0.27;稳定运行期进出水pH差值由启动时的0.85下降到0.24。启动期反硝化和厌氧氨氧化反应同时存在而在稳定运行期厌氧氨氧化发展成为主导反应。MLSS和MLVSS/MLSS先减少后增加,反映了启动过程中硝化细菌、反硝化细菌的衰亡和厌氧氨氧化菌逐渐富集的过程,这与反应器的宏观运行效果相一致。     

Modeling photocatalytic destruction of the organic contaminants in continuous stir flow reactor

Thin-film technique is becoming an industry standard for the preparation of TiO₂-based photocatalyst for organic destruction. The catalyst provides several advantages over the conventional powder TiO₂ in the treatment of wastewater and groundwater. In this study, a continuous stir flow reactor model is developed capable of describing the photocatalytic process. The model incorporates the following fundamental mechanisms: adsorption, diffusion, liquid-film transfer, UV attenuation, and photocatalytic reaction. All of the simulation results indicate that there exists a highly nonlinear relation between each of these parameters and the destruction rate. Various incident light intensities also are incorporated to simulate the energy efficiency. The simulations illustrate that the photocatalytic model can be used to elucidate the effect of process variables. It is also possible to “custom-design” a catalyst for the treatment of a particular waste stream.     

TiO2-Cu2O/蒙脱土复合光催化剂的制备与性能

以钠基蒙脱土（MMT）为载体,先采用溶胶-凝胶法将纳米TiO₂引入到MMT层间,再采用化学沉积法将纳米Cu₂O负载在TiO₂/MMT上,制备出TiO₂-Cu₂O/MMT纳米复合光催化剂。采用XRD、SEM、紫外-可见漫反射技术对催化剂进行了表征。以甲基橙为目标污染物,考察了催化剂的光催化性能。表征结果显示：TiO₂与Cu₂O均匀分布在MMT的表面与片层孔隙中;TiO₂-Cu₂O/MMT结合了TiO₂和Cu₂O的特性,拓宽了催化剂的光吸收范围。实验结果表明,在光源为可见光、初始甲基橙质量浓度为20 mg/L、光催化剂加入量为2 g/L的条件下,TiO₂-Cu₂O/MMT纳米复合光催化剂对甲基橙的光催化降解效果明显优于单一负载的Cu₂O/MMT和TiO₂/MMT,大幅提高了催化剂的光催化效率,反应300 min时TiO₂-Cu₂O/MMT对甲基橙溶液的脱色率达到93%。     

Multi-response optimization of Fenton process for applicability assessment in landfill leachate treatment

Fenton process, as a pretreatment method, was found to be effective in the primary treatment of mature/medium landfill leachate. However, the main problem of the process is the large amount of produced sludge that requires an accurate feasibility evaluation for operational applications. In this study, the response surface methodology was applied for the modeling and optimization of Fenton process in three target responses, (1) overall COD removal, (2) sludge to iron ratio (SIR) and (3) organics removal to sludge ratio (ORSR), where the latter two were new self-defined responses for prediction of sludge generation and applicability assessment of the process, respectively. The effective variables included the initial pH, [H₂O₂]/[Fe²⁺] ratio and Fe²⁺ dosage. According to the statistical analysis, all the proposed models were adequate (with adjusted R² of 0.9116–0.9512) and had considerable predictive capability (with prediction R² up to 0.9092 and appropriate adequate precision). It was found that all the variables had significant effects on the responses, specifically by their observed role in dominant oxidation mechanism. The optimum operational conditions obtained by overlay plot, were found to be initial pH of 5.7, [H₂O₂]/[Fe²⁺] ratio of 17.72 and [Fe²⁺] of 195 mM, which led to 69% COD removal, 2.4 (l sludge/consumed mole Fe²⁺) of SIR and 16.5 (gCOD removed/l produced sludge) for ORSR in verification test, in accordance with models-predicted values. Finally, it was observed that [H₂O₂]/[Fe²⁺] ratio and Fe²⁺ dosage had significant influence on COD removal, while Fe²⁺ dosage and [H₂O₂]/[Fe²⁺] ratio had remarkable effects on SIR and ORSR responses, respectively.