添加H2O2加速低合金钢海水腐蚀的主要影响因素研究

采用极化曲线、旋转圆盘电极试验和失重（质量损失）法研究了低合金钢在添加了H。o：的海水中腐蚀加速的主要影响因素。结果发现低合金钢在添加H2O2的海水中腐蚀加速主要受到了H2O2浓度、温度、搅拌速度和H2O2添加周期的影响。研究表明,搅拌速度不变、H2O2添加周期相同的条件下,在H2O2浓度为0．8mol／L的70℃海水中,低合金铜的腐蚀加速最显著;在试验的转速范围内,加速作用随搅拌速度增大变得更为显著;H2O2加入后350min内加速作用较明显。     

抗滑桩细观受力特征的数值模拟研究

抗滑桩是滑坡防治工程中一种非常有效的支挡措施,其受力特征直接关系到滑坡防治效果,因此开展抗滑桩细观受力特征的数值模拟研究具有重要的工程应用价值。基于有限元数值模拟方法,采用ANSYS软件中的分离式模型,以SOLID65单元和LINK8单元分别模拟钢筋混凝土抗滑桩中的混凝土和钢筋,研究了不同荷载作用下抗滑桩的细观受力特征。结果表明:在相同荷载作用下,抗滑桩在高度较小阶段,其高度与抗滑桩的变形呈非线性变化,随着抗滑桩高度的增加,其高度与抗滑桩的变形趋于线性关系;有限元数值模拟能较好地反映钢筋混凝土抗滑桩的细观受力特征。该研究可以为抗滑桩工程的设计提供借鉴与参考。     

火灾下钢框架结构热-力耦合模拟与性能分析

基于"自然火灾安全概念"(NFSC)的基本思想,提出了火灾下钢结构热-力耦合模拟方法。利用ANSYS的参数化设计语言,建立了ANSYS软件与OZone火灾分析软件的数据接口,实现了火灾分析软件与大型有限元软件的耦合运用。基于火灾模拟软件OZone的分析结果,利用APDL语言,对钢框架结构进行了真实火灾场景下的热-力耦合模拟。研究表明:钢框架结构在真实火灾场景下,受非均匀变热流影响,结构内部将产生热应力梯度和应力牵移现象;同时钢框架中钢梁固接时,火灾初期变形较小,当达到某个关键时间点后将开始大的变形破坏,其主要原因是钢框架内部产生塑性铰,即钢梁由固接变为铰接,释放了对钢梁的约束。     

Effect of oxide-based fluxes on mechanical and metallurgical properties of Dissimilar Activating Flux Assisted-Tungsten Inert Gas Welds

Present investigation is to study the “Effect of Activating Fluxes on Mechanical and Metallurgical Properties of Dissimilar Activated Flux-Tungsten Inert Gas Welds”. Effect of current, welding speed, joint gap and electrode diameter on weld bead dimensions on 6 mm thick dissimilar weld between carbon steel to stainless steel, was studied under Activated Flux-Tungsten Inert Gas Welding process. During this investigation three different types of oxide powders were used-TiO₂, ZnO and MnO₂. After welding samples were subject to mechanical testing, in addition to characterization via micro hardness and microstructures of Normal Tungsten Inert Gas Welds and Activated Flux-Tungsten Inert Gas Welds. Activating fluxes TiO₂ and ZnO are effective fluxes for Activated Flux-Tungsten Inert Gas Welding of dissimilar weld between CS to SS. Highest depth/width (D/W) ratio reported under TiO₂ and ZnO fluxes compare to Normal-Tungsten Inert Gas Welds. Lowest angular distortion was observed under TiO₂ flux compare to Normal-Tungsten Inert Gas Welds. Mechanical properties, Joint Efficiency of Activated Flux-Tungsten Inert Gas Welds are higher than normal-Normal Tungsten Inert Gas Welds. Tensile Test specimens of both the processes failed from the parent metal (carbon steel side). Carbon migration from CS to SS, had occurred which led to failure of weld joints from CS side.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

45~#钢在西双版纳大气环境下的腐蚀研究

目的研究西双版纳热带雨林地区大气环境下材料的初期腐蚀行为。方法使用45#碳钢在西双版纳大气环境下进行1年的大气暴露腐蚀试验,并利用质量损失分析、SEM、XRD和FTIR等技术,分析45#碳钢在西双版纳大气环境下暴露1年的腐蚀行为。结果 45#碳钢的腐蚀产物以γ-FeOOH,Fe(OH)3和Fe3O4为主,并有少量的α-FeOOH。结论西双版纳大气环境腐蚀性为C2级。在暴露1年的时间内,锈层化学稳定性随试验时间的延长逐渐增强,对基体的保护性逐渐加大。     

某大型钢结构项目喷涂废气污染防治措施可行性分析研究

钢结构建筑是一种新型的节能环保的建筑体系,大多数大型钢结构产品在生产过程中均需要进行抛丸除锈、喷涂处理,使用油漆进行喷涂过程中将不可避免地产生含TVOC(主要为甲苯、二甲苯和非甲烷总烃)的有机废气。大型钢构类生产项目喷涂废气的收集和处理尤为困难。文章结合某大型钢结构生产企业实际采取的喷涂废气治理方法进行喷涂废气污染防治可行性分析,旨在为同类项目喷涂废气污染治理及进一步改良涂装废气治理工艺和技术提供参考依据。     

双层板桁钢梁应力分析

以跨度最大的双层斜拉桥闵浦大桥为背景,研究了双层板桁钢梁桥面板的受力特性,阐述了精细壳单元与梁单元结合的整体有限元模型,并分析了上、下桥面间腹杆的受力特性与桥面板的应力分布特性;采用桥面纵横梁间带U肋精细桥面模型,分析了桥面板和U肋在车辆荷载作用下的应力分布.研究表明,上、下层桥面横桥向应力小于纵桥向应力,并且横桥向应...     

设置限位器双向隔震铁路桥梁车桥耦合动力响应研究

对铅芯橡胶双向隔震铁路桥梁在列车荷载作用下的力学性能进行了研究,针对双向隔震铁路桥梁中存在的问题,提出了设置限位器的解决方案,并对设置限位器的双向隔震铁路桥梁进行了车桥耦合动力响应分析.研究结果表明,采用常规隔震设计方法的铅芯橡胶支座在横桥向的初始刚度和屈服强度均不能满足规范要求,设置限位器后,双向隔震铁路桥梁的力学性...     

不同构造措施的钢管混凝土边框钢板剪力墙抗震性能试验研究

钢管混凝土边框钢板剪力墙是一种新型抗震剪力墙,为了比较不同构造措施对该新型剪力墙抗震性能的影响,进行了3个剪跨比为1.5的钢管混凝土边框钢板剪力墙低周反复荷载试验.其中,试验模型1为墙体钢板与边框柱钢管焊接,试验模型2为墙体钢板与边框柱钢管螺栓连接,试验模型3为墙体钢板开孔并与边框柱钢管焊接.通过试验研究,比较了各剪力...