A full-scale sequencing batch reactor system for swine wastewater treatment

A full-scale sequencing batch reactor (SBR) system was evaluated for its ability to remove carbon and nitrogen from swine wastewater. The SBR was operated on four, six-hour cycles each day, with each cycle consisting of 4.5 hours of “React,” 0.75 hours of “Settling”, 0.75 hours for “Draw” and “Fill.” Within each cycle, an amount of wastewater equivalent to about 5% of the reactor volume (5,500 litres) was removed and added. The SBR system was able to remove 82% of biochemical oxygen demand (BOD) and more than 75% of nitrogen. Even though the SBR effluent, with an average effluent BOD₅ of about 588 mg L^{? 1}, did not meet the discharge criteria, it enabled a reduction of the land base required for land application of swine wastewater by about 75%. Results indicated that the SBR system was a viable method for the treatment of swine wastewater.     

Treatment of wastewater from red and tropical fruit wine production by zeolite anaerobic fluidized bed reactor

A study of the anaerobic treatment of wastewaters derived from red (RWWW) and tropical fruit wine (TFWWW) production was carried out in four laboratory-scale fluidized bed reactors with natural zeolite as bacterial support. These reactors operated at mesophilic temperature (35°C). Reactors R1 and R2 contained Chilean natural zeolite, while reactors R3 and R4 used Cuban natural zeolite as microorganism support. In addition, reactors R1 and R3 processed RWWW, while reactors R2 and R4 used TFWWW as substrate. The biomass concentration attached to zeolites in the four reactors studied was found to be in the range of 44–46 g volatile solids (VS)/L after 90 days of operation time. Both types of zeolites can be used indistinctly in the fluidized bed reactors achieving more than 80%–86% chemical oxygen demand (COD) removals for organic loading rates (OLR) of up to at least 20 g COD/L d. pH values remained within the optimal range for anaerobic microorganisms for OLR values of up to 20 and 22 g COD/L d for RWWW and TFWWW, respectively. Toxicity and inhibition levels were observed at an OLR of 20 g COD/L d in reactors R1 and R3 while processing RWWW, whereas the aforementioned inhibitory phenomena were not observed at an OLR of 24 g COD/L d in R2 and R4, treating TFWWW as a consequence of the lower phenolic compound content present in this substrate. The volatile fatty acid (VFA) levels were always lower in reactors processing TFWWW (R2 and R4) and these values (< 400 mg/L, as acetic acid) were lower than the suggested limits for digester failure. The specific methanogenic activity (SMA) was twice as high in reactors R2 and R4 than in R1 and R3 after 120 days of operation when all reactors operated at an OLR of 20 g COD/L d.     

微电解预处理靛蓝牛仔布印染废水

靛蓝牛仔布印染废水组分复杂,浓度高、水量大,属于难处理的工业废水,为了有效降低后续生物处理单元的负荷,采用铁炭微电解工艺对该废水进行预处理;通过正交实验考察pH、反应时间及铁炭比处理效果的影响规律及COD去除反应动力学,并对各因素作了单因素影响实验,确定了最佳工艺条件.结果表明,铁炭微电解法是预处理靛蓝牛仔布印染废水的一种有效方法,在Fe/C为2:1、pH为3的条件下反应90 min,铁炭微电解出水COD的去除率在49.2％,色度去除率达到80％,该印染废水经微电解处理后,BOD5/COD比值可从原来的0.248上升至0.436,可生化性明显提高.此外,微电解预处理靛蓝牛仔布印染废水中COD的去除反应符合二级反应动力学规律.     

Fenton氧化法深度处理抗生素废水二级出水

采用Fenton氧化法对青霉素和土霉素混合废水二级处理出水进行深度处理,通过正交和单因素实验研究了废水初始反应pH值、H2O2投加量、Fe2+/H2O2摩尔比及反应时间等因素对废水处理效果的影响。实验结果表明,Fenton氧化法处理的最佳反应条件为:初始pH值4、H2O2(30%)投加量50 mL/L、Fe2+/H2O2摩尔比1/20和反应时间60 min,处理后出水COD小于120 mg/L,COD去除率在75%以上,急性毒性(HgCl2毒性当量)小于0.07 mg/L,满足《发酵类制药工业水污染物排放标准》(GB21903-2008)表2标准要求。     

工业废水中多金属离子的吸附净化

以含有Si、Al、Ca、C元素的矿物材料作为基质,经特定条件处理后造粒成型加工成轻质多孔Si-Al-Ca-C结构的吸附材料。研究了该吸附材料对工业废水中多种金属离子的吸附性能,探讨了影响吸附性能的因素。研究结果表明,在一定条件下,Si-Al-Ca-C吸附材料对工业废水中Al3+、Ca2+、Mn2+、Cu2+、Fe3+、Mg2+、As3+和Zn2+的净化率分别高达99.34%、99.82%、98.26%、98.16%、97.76%、97.01%、100%和89.09%。金属离子残留浓度分别为0.152、0.07、0.012、0.02、0.119、0.311、0和0.259 mg/L,均低于国家污水综合排放标准(GB8978-1996)一级标准。     

萃取净化电镀含镉废水

研究了二壬基萘磺酸(DNNSA)形成的微乳液从模拟含镉废水中萃取镉离子的工艺条件。分别考察了相体积比(O/A)、萃取时间、温度及萃取剂浓度对废水中镉离子萃取的影响。结果表明,萃取平衡时间为10 mim,降低温度及增加萃取剂浓度均有利于萃取。紫外光谱证实当DNNSA萃取镉时,所形成萃合物对萘环的结构无影响,且不会破坏微乳相的结构;分子荧光光谱表明镉离子对配体DNNSA有荧光猝灭作用。     

三维电极法深度处理维生素生产废水

采用三维电极法对维生素废水进行深度处理,分别以钛涂钌铱板、铁板和不锈钢板作为电极阳极,石墨板作为电极阴极,柱状活性炭作为粒子电极,结果表明,当以钛涂钌铱板作为阳极,以粒径为1 mm的柱状活性炭作为粒子电极时电解效果最好,COD和色度去除率最高。实验选择电解电压、电极板间距、电解时间和初始pH值作为主要影响因素进行正交实验,实验研究证明,各因素的影响大小为电解电压>电极板间距>电解时间>初始pH值,得到的最佳参数组合分别为:电解电压为10 V,电极板间距为8 cm,电解时间为20 min,初始pH值为4,得到COD和色度最大去除率分别为59.5%和93.57%。     

SBR处理模拟氯苯废水

在SBR中利用光合细菌球形红细菌污泥颗粒进行模拟氯苯废水处理的初步研究,结果表明,采用球形红细菌污泥颗粒处理模拟氯苯废水的SBR系统是可行的,其降解氯苯过程符合Monod一级反应动力学方程。当进水氯苯浓度在125～187.5 mg/L变化时,处理效率都能稳定在90.5%～95.6%之间;其最佳工艺条件为反应时间6 h、DO 4.75～5.0 mg/L、沉淀时间1.5 h、污泥颗粒浓度4 000～6 000 mg/L。在污泥颗粒浓度4 000 mg/L、DO 5.0 mg/L、反应时间6 h的最佳条件下,当进水COD为748.1 mg/L、氯苯浓度100 mg/L时,COD的去除率达90.9%,处理后出水COD满足国家一级排放标准要求。     

Fenton氧化-序批式膜生物反应器耦合处理干法腈纶废水

采用Fenton氧化-序批式膜生物反应器(SBMBR)组合工艺处理干法腈纶废水。结果表明,在废水初始pH值为3.0,H2O2投加量为90.0 mmol/L,Fe2+投加量为20.0 mmol/L,反应时间为2.0 h的条件下,Fenton氧化预处理对腈纶生产废水的COD去除率达到47.0%以上,COD由1 091 mg/L降至560 mg/L,废水的BOD5/COD由0.32升至0.69,废水的可生化性得到显著提高。Fenton处理出水与丙烯腈废水等比例混合后,采用SBMBR进行生化处理,在水力停留时间为24 h,90 min缺氧/150 min好氧交替运行的条件下,COD、NH4+-N和TN的平均去除率分别为71.7%、97.2%和47.4%,碳源不足是限制TN去除效果的主要影响因素。在无外加碳源的条件下,组合工艺处理后出水COD和NH4+-N浓度分别为117 mg/L和1.7 mg/L,出水水质可以稳定达到国家一级排放标准(GB8978-1996)。     

混凝沉淀去除丙烯酸丁酯废水浊度物质

采用混凝沉淀法去除丙烯酸丁酯废水中的浊度物质,比较6种混凝剂的去除效率,确定聚合氯化铝为适宜混凝剂,并选用阳离子型聚丙烯酰胺作为助凝剂。研究结果表明,聚合氯化铝和阳离子型聚丙烯酰胺的优化投加量分别为150 mg/L和20 mg/L,优化pH值为4～5,水温20～40℃,快速搅拌速度200～400 r/min,搅拌时间1～3 min,慢速搅拌速度50～80 r/min,搅拌时间5～15 min。在以上条件下,可使出水浊度从3 000 NTU左右降至1 NTU左右,同时也实现了废水中胶体物质的大量去除。