The Thermal Discharges From Nuclear Power Plants in Taiwan

The increasing use of sea water for industrial cooling presents a real threat to the ecological environment in the ocean. in Taiwan where many electric power plants along the coast take sea water for cooling, people are concerned seriously about nuclear power plants. There are three nuclear power plants in Taiwan. Each plant has two units for generating power. the first two are located along the northern coast of Taiwan. the third is located in Kenting National Park along the coast of southernmost Taiwan. the plants take sea water for cooling, and discharge their heated effluents to the ocean surface from the coast. the thermal effluents have variable effects on the ecological environment near the plants. Fishermen living near the power plants complain that the heated water affects the inshore fishery catch. in addition, the thermal water from the second plant is easily accumulated near the coastal zone to influence the nearby swimming area in the summer-time. the thermal water from the third plant bleaches or kills some corals in shallow water near the outlet, and this conflicts with the interests of Kenting National Park.     

垃圾焚烧烟气中HCl与消石灰的反应机理研究

测试了两种消石灰与垃圾焚烧烟气中HCl的反应率,得出了消石灰的反应率与反应时间的反应曲线,分析了消石灰与HCl的反应机理及影响消石灰最终反应率的因素。试验结果表明,消石灰与HCl反应初期按灰层扩散控制进行,两种消石灰的最终反应率分别为16％和36％。     

铝系混凝剂优势形态分析及其混凝特性

聚合氯化铝（PACl）是常用的水处理混凝剂,在应用过程中通常表现出比传统铝盐更为优异的效果.研究表明,这种优异性能主要得益于其特殊的组成,特别是高分子聚合物Al₁₃和Al₃₀独特的物化特性.Al₁₃和Al₃₀是铝离子水解过程中的中间产物,在地球科学和环境化学等领域有着重要的研究价值.于水处理而言,二者的结构和分子特性是研究者关注的重点,大量研究基于此展开,很多重要的发现为实际应用奠定了基础.基于对PACl及其组成性质的研究,本文对PACl的混凝特性及其优势形态分子的分析进行了综合阐述.     

深圳市秋季大气臭氧立体分布特征

利用大气O₃探测激光雷达在深圳市东部生态区和西部城区同步开展垂直观测,探究了2018年深圳市O₃立体分布在秋季光化学污染活跃期至冬季非活跃期的演变过程.结果表明：光化学反应活跃的10月,东部地面O₃浓度相对于西部地面高出约128%;地面向上至450m,O₃浓度在东部生态区发生快速降低,而在西部城区由于存在“滴定效应”,O₃浓度随高度升高而升高;450m~2km,东、西部O₃浓度均随高度升高而降低,西部城区O₃浓度水平超过东部生态区约30%;2km以上高空,东、西部O₃浓度趋同（70μg/m³）,并保持稳定,为具深圳市秋季O₃污染过程提供了较高的大气背景浓度.高污染期间,深圳市大气边界层内O₃浓度变化较为一致,西部高空的O₃区域传输作用更加显著.秋季至冬季光化学反应逐渐减弱,深圳市O₃浓度的水平和垂直空间差异逐渐减小,冬季的深圳市O₃污染基本受大气背景控制.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

石英灯辐射加热条件下低密度碳/酚醛复合材料高温响应及分析

目的研究低密度碳/酚醛复合材料在不同地面加热实验测试响应的差异性,指导材料在实际应用环境下的高温响应分析。方法对低密度碳/酚醛复合材料开展了热流为400 kW/m~2的单侧石英灯辐射加热实验,利用热电偶测温系统测量试件在加热过程中不同位置的温度时间历程,并对试件的烧蚀形貌和微观结构进行观测。同时与热流为464k W/m~2的氧乙炔加热陶瓷板辐射加热实验结果进行对比分析,并且采用有限元方法对材料的传热传质多场耦合计算进行分析。结果对于石英灯辐射加热,在测量点升温到接近200℃时,温度响应拐点都依次出现。由于加热的辐射热源不同,在不同的辐射波段下,多孔材料吸收和发射的热量不同,短时间内氧乙炔加热陶瓷板辐射加热使材料内部升温速率比石英灯辐射加热实验的要快,但长时间加热时现象刚好相反。结论进行传热传质多场耦合计算材料高温响应时,合理确定材料宏观性能随温度的变化至关重要。     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

包装箱用碳纤维增强复合材料贮存寿命研究

目的研究碳纤维增强复合材料贮存条件下的性能变化趋势和寿命评估。方法对碳纤维增强复合材料开展四个不同温度条件下的热氧老化试验,按试验周期定期取样开展冲击性能测试,对试验数据采用寿命预估方法进行处理,对材料性能进行预估。结果通过数据计算分别得到我国热带海洋、干热沙漠等典型气候条件下的碳纤维增强复合材料贮存寿命分别为17.21~35.89年。结论碳纤维增强复合材料具有较好的贮存性能,在较为严酷的热带海洋气候和给定的失效判据条件下,寿命预计为17.21年。试验和数据处理方法可以较好地预计材料的性能变化趋势和开展寿命评估。     

Estimation of the Thermal Sensitivity of a Dwelling to Variations in Architectural and Behavioural Parameters

The provision of energy for households is a major contributor to greenhouse gas emissions in the domestic sector. There is significant scope for energy savings and thus emission reduction in this sector. This paper constructs a bridge between thermal analysis and environmental assessment in the occupancy stage of the dwelling life cycle, approaching both methods as being on a common system Environment–Dwelling–Inhabitant. The importance of the local level in the thermal analysis and assessment of either a dwelling or an inhabitant's behaviour is demonstrated. It is shown that the researcher can choose between natural experiment, computer experiment and mathematical modelling to analyze the system. Such a choice is discussed for two particular methods of thermal analysis. Thermal Nomograms are the result of mathematical modelling, and the Energy Score Sheet is the result of a computer experiment in energy rating. Despite being developed for the purpose of thermal analysis, these methods can also be utilized for environmental assessment at the local level. The discussion centres on Australian conditions where the majority of the population resides in a relatively benign climate wherein behavioural alterations have significant potential for energy savings and environmental impact. The purpose of the paper is to emphasise benefits apart from energy minimisation to promote the use of energy efficient housing strategies.