BOD5测定方法的研究

通过对比实验，对BOD5的测定方法进行研究，探索用氧电极法测定BOD5的可能性和可行性，对其不足之处提出相应的解决措施，使之能更适用于科研、监测教学等方面的需要。     

利用多次回归拟合水的饱和蒸气压与温度的关系表达式

在使用于湿球测定锅炉烟气含湿量的过程中,需要查找水的饱和蒸气压,非常不方便.利用D-196和<化工原理>上册中取得部分数据,用多次线性回归的方法,拟合出水在0～200℃范围内的饱和蒸气压与温度的关系表达式;并对该表达式的误差进行了分析,误差均值为0.2‰,最大值也只有0.8‰,完全可以满足环境监测中数据处理的精度要求.     

Membrane fouling control by ultrasound in an anaerobic membrane bioreactor

In this study, ultrasound was used to control the membrane fouling online in an anaerobic membrane bioreactor (AMBR). Short-term running experiments were carried out under different operating conditions to explore feasible ultrasonic parameters. The experimental results indicated that when the crossflow velocity was more than 1.0 m/s, membrane fouling could be controlled effectively only by hydrodynamic methods without ultrasound. When ultrasound was applied, an ultrasonic power range of 60–150 W was suitable for the membrane fouling control in the experimental system. The experimental results showed that the membrane fouling was controlled so well that membrane filtration resistance (ΣR) could stay at 5 × 10¹¹ m⁻¹ for more than a week with the crossflow velocity of 0.75 m/s, which equaled the effect of crossflow velocity of more than 1.0 m/s without ultrasound. Translated from Techniques and Equipment for Environmental Pollution Control, 2006, 7(4): 25–29 [译自: 环境污染治理技术与设备]     

半球形件粘性介质压力成形的数值模拟研究

粘性压力成形技术是金属板材成形领域里新近出现的一种先进的加工工艺。对双面施放粘性介质的板材胀形进行了模拟研究 ,在双面施放介质的板材粘性介质胀形时 ,排放孔位置分布对毛坯成形过程有明显的影响。排放孔位置分布的不同造成模腔内介质的速度场不同 ,进而导致板材不同部位的流动速度的方向大小发生变化 ,最终使成形件的厚度分布不同     

利用合成氨二段转化气联产甲醇技术的可行性分析

通过对国内外不同甲醇合成生产工艺技术概况及能耗指标的分析，探讨合成氨化肥企业利用现有工艺技术进行改造的可行性，以提高企业对市场的适应性。     

石脑油罐压力安全阀泄漏的隐患治理

石脑油罐压力安全阀泄漏，严重威胁生产与施工的安全进行。通过拆检，弄清了安全阀泄漏的原因，采取了相应措施，彻底解决了这一重大安全隐患。     

A／O-化学除磷工艺中DMBR动态膜成膜条件研究

根据动态膜原理，将0．1mm孔径无纺布为膜材的动态膜反应器（Dynamic Membrane BioReactor，DMBR）应用于A／O-化学除磷工艺之中，在动态膜反应器内完成泥水分离。试验测试了曝气强度、初始膜通量和污泥浓度对动态膜成膜的影响。结果表明，曝气强度和初始膜通量是影响成膜的关键性参数。当曝气强度≥60m^3／m^2·h或初始膜通量≥70L／m^2·h，2h内均不能形成截留性能良好的动态膜。在VSS／SS较低的污泥系统中，适宜的成膜条件为：曝气强度≤40m^3／m^2·h；初始膜通量≤40L/m^2·h。     

生物膜反应器处理洗涤污水的试验

介绍了采用生物膜反应器处理洗涤污水的试验研究方法，研究了COD、LAS和NH3-N的去除效果。试验结果表明：整个系统出水稳定，水质良好（COD〈38．7mg／L、NH3-N〈1．1mg／L、LAS〈0．9mg／L，且无色无味、无SS），符合国家建设部生活杂用水回用水质标准，且具有较强的抗冲击负荷能力。在生物膜反应器中，微生物对污染物的去除起主要作用，而中空纤维膜对维持系统的稳定出水起重要作用。     

陶瓷微滤膜过滤黑液的清洗与再生

对无机陶瓷微滤膜过滤草桨黑液的膜清洗及再生的方法进行了研究。考察了物理和化学方法的再生效果、单种清洗剂的清洗效果、复合方法的清洗效果和效果的可重复性。结果表明物理冲洗、高温灼烧、单一的化学清洗剂清洗均可以提高陶瓷膜的再生通量；但是复合方法对陶瓷微滤膜的再生效果较好，其中按氢氧化钠溶液清洗、硝酸溶液清洗、次氯酸钠溶液清洗的实验步骤，膜的再生渗透通量高．且重复性强，可望在工业生产的在线清洗中应用。     

Fulvic acid removal by nanoparticle TiO2 using a submerged membrane photocatalysis reactor

The degradation of fulvic acid（FA） by nanoparticle TiO2 in a submerged membrane photocatalysis（SMPC） reactor was studied. In this reactor, photocatalytic oxidation and membrane separation co-occured. The continuous air supplier provided O2 for the photocatalytical reaction and mixed the solution through an airflow controller. The particle TiO2 could automatically settle due to gravity without particle agglomeration so it could be easily separated by microfiltration（MF） membrane. It was efficient to maintain high flux of membranes. The effects of operational parameters on the photocatalytic oxidation rate of FA were investigated. Results indicated that photocatalyst at 0.5 g/L and airflow at 0.06 m^3/h were the optimum condition for the removal of fulvic acid, the removal efficiency was higher in acid media than that in alkaline media. The effects of different filtration duration on permeate flux rate of MF with P25 powder and with nanoparticle TiO2 were compared. Experimental results indicated that the permeate flux rate of MF was improved and the membrane fouling phenomenon was reduced with the addition of nanoparticle TiO2 catalyst compared with conventional P25 powder. Therefore, this submerged membrane photocatalysis reactor can faciliate potential application of photocatalytic oxidation process in drinking water treatment.