水体中甲基汞光化学降解特征研究

为探究水体中甲基汞（MMHg）的光化学行为,采用室内模拟实验,以不同波长紫外灯及室内可见光为光源,探讨紫外光波长、光强度等因素对MMHg光降解的影响,并根据生成物Hg0的量变化分析MMHg光降解反应历程.研究表明,MMHg光降解最终产物中含有Hg0,且光照条件对MMHg光降解速率、Hg0的产量有影响.在反应器暴露于紫外光条件下时,MMHg光降解速率随紫外光波长的变短而增加,随紫外光强度的提高而增加,且MMHg光降解呈一级动力学反应,速率常数分别为KUVA 0.403～0.562 h-1、KUVB 0.961 h-1、KUVC 1.221 h-1和KVL＋UVA＋UVB 1.346 h-1;Hg0释放通量为0.166～0.392 ng·min-1.当反应器暴露于可见光条件下时,反应器内MMHg浓度下降速率较慢,KVL0.061 h-1;Hg0释放通量为0.008 ng·min-1.而在黑暗条件下没有发现反应器内MMHg浓度下降,无Hg0生成.可见紫外光是导致MMHg降解的主要原因,光波波长与强度对MMHg的环境地球化学行为有重要影响.     

umu试验研究饮用水氯和氯胺消毒过程中遗传毒性的变化以及消毒条件的影响

采用umu遗传毒性测试方法考察了消毒剂投加量、反应时间和消毒剂氯氮比对某饮用水厂臭氧-生物活性炭出水加氯或氯胺消毒前后遗传毒性的影响.结果表明,炭后水具有一定的遗传毒性(20～70 ng/L),加氯或氯胺消毒后遗传毒性增加.反应时间为24 h,在相同投加量下氯消毒遗传毒性(40～95 ng/L)高于氯胺消毒遗传毒性(20～40 ng/L);当氯初始投加量从0 mg/L增加到10 mg/L时,炭后水的遗传毒性先迅速增加,在0.5～1 mg左右达到极大值,然后再降低,在3～5 mg左右达到极小值后缓慢上升,但是氯胺消毒后水样遗传毒性变化规律不如氯消毒的明显.当投加量为3 mg/L时,随着反应时间从0 h延长至72 h,无论是氯消毒还是氯胺消毒,炭后水遗传毒性均是先迅速增加,在2 h时达到极大值后再下降,在18 h左右达到极小值然后缓慢上升,而且任意反应时间内,氯胺消毒的遗传毒性(20～62 ng/L)均小于氯消毒(83～120 ng/L).本试验还研究了消毒剂氯氮比对炭后水氯消毒后遗传毒性的影响.在本试验条件下,从遗传毒性的角度看,对于饮用水消毒氯胺比氯更安全,而且2种消毒方式的遗传毒性的变化规律均不同于总HAAs的变化规律.     

微波消毒技术在医疗废物处理中的应用

本文通过对微波技术的调查,全面总结了医疗废物微波消毒系统的机理、设备组成、影响消毒效果的主要因素、设备的优越性和人体保护注意事项等。     

水中天然有机物的分类特性及其卤代活性

利用XAD树脂对原水中的天然有机物进行富集分类 ,将其分为腐植酸、富里酸、亲水酸和其它亲水物质等 4种有机组分 .考察了原水中各有机组分的分布及其在加氯消毒过程中的三卤甲烷生成量、生成速度及耗氯量情况 .研究结果表明 ,原水中的主要成分是富里酸 ,占有机物总量的50.7% ,其它3种成分所占比例相对较小 ;原水具有较高的三卤甲烷生成能力 ,富里酸是生成三卤甲烷的主要有机组分 ;对各有机组分卤代活性的研究表明 ,腐植酸、富里酸和亲水酸具有较高的卤代活性 ,其它亲水物质的卤代活性较低 ;从各有机组分的三卤甲烷生成速度及与氯反应速度来看 ,腐植酸、富里酸及亲水酸具有较快的三卤甲烷生成速度 ,与氯的反应速度也较快 ,而其它亲水物质的三卤甲烷生成速度及与氯的反应速度均较低 .     

臭氧耦合陶瓷膜过滤对膜性能及出水消毒副产物的影响

利用臭氧（O₃）-陶瓷膜过滤（CMF）处理常规工艺出水,研究了不同O₃-CMF耦合方式对膜性能和消毒副产物（DBPs）的影响.结果表明,与单独CMF相比,异位O₃-CMF和原位O₃-CMF均可以有效缓解膜污染,原位O₃-CMF控制效果最佳.异位O₃-CMF对进水（常规工艺出水） DOC去除率（26.25%）略高于原位O₃-CMF（22.31%）,但是其SUVA去除率（83.91%）明显低于原位O₃-CMF（93.10%）.羟基自由基（·OH）生成特征表明原位O₃-CMF可促进O₃产生更多的·OH.在O₃、·OH氧化和陶瓷膜截留协同作用下,异位O₃-CMF和原位O₃-CMF出水中总荧光响应强度和相对分子质量大于0.3×10³,有机物含量降低,进而使得出水中含碳消毒副产物（C-DBPs）生成量分别降低了21.86%和32.35%,含氮消毒副产物（N-DBPs）生成量分别降低了16.16%和19.13%.但O₃和·OH氧化后生成的小分子有机物因难以被CM截留导致其在出水中含量增加,进而增加了卤代酮（HKs）、水合氯醛（CH）和三卤硝基甲烷（THNMs）的产生.本研究对于不同O₃-CMF方式下O₃与CM的协同机制的探讨,改善膜性能和提升DBPs前体物的去除具有一定指导意义.     

Comparison of inclined plate sedimentation and dissolved air flotation for the minimisation of subsequent nitrogenous disinfection by-product formation

The formation of disinfection by-products (DBPs), including both nitrogenous disinfection by-products (N-DBPs) and carbonaceous disinfection by-products (C-DBPs), was investigated upon chlorination of water samples following two treatment processes: (i) coagulation-inclined plate sedimentation (IPS)-filtration and (ii) coagulation-dissolved air flotation (DAF)-filtration. The removal of algae, dissolved organic nitrogen (DON), dissolved organic carbon (DOC) and UV₂₅₄ by coagulation-DAF-filtration was superior to coagulation-IPS-filtration. On average, 53%, 53% and 31% of DOC, DON and UV₂₅₄ were removed by coagulation-DAF-filtration process, which were higher than 47%, 31% and 27% of that by coagulation-IPS-filtration process. Additionally, coagulation-IPS-filtration performed less well at removing the low molecular weight organics than coagulation-DAF-filtration process. The concentrations of chloroform, dichloroacetamide (DCAcAm) and dichloroacetonitrile (DCAN) formed during chlorination after coagulation-DAF-filtration reached their maximum values of 13, 1.5 and 4.7 μg L⁻¹, respectively, and were lower than those after coagulation-IPS-filtration with the maximum detected levels of 17, 2.9 and 6.3 μg L⁻¹. However, the trichloronitromethane (TCNM) concentration after the two processes was similar, suggesting that DON may have less of a contribution to TCNM formation than DCAcAm and DCAN.     

Escherichia coli inactivation by pressurized CO2 treatment methods at room temperature: Critical issues

This study aims to increase the inactivation efficiency of CO_2 against Escherichia coli under mild conditions to facilitate the application of pressurized CO_2 technology in water disinfection. Based on an aerating-cycling apparatus, three different treatment methods(continuous aeration, continuous reflux, and simultaneous aeration and reflux) were compared for the same temperature, pressure(0.3–0.7 MPa), initial concentration, and exposure time(25 min). The simultaneous aeration and reflux treatment(combined method) was shown to be the best method under optimum conditions, which were determined to be 0.7 MPa, room temperature, and an exposure time of 10 min. This treatment achieved 5.1-log reduction after 25 min of treatment at the pressure of 0.3 MPa and 5.73-log reduction after 10 min at 0.7 MPa. Log reductions of 4.4 and 5.0 occurred at the end of continuous aeration and continuous reflux treatments at 0.7 MPa, respectively.Scanning electron microscopy(SEM) images suggested that cells were ruptured after the simultaneous aeration and reflux treatment and the continuous reflux treatment. The increase of the solubilization rate of CO_2 due to intense hydraulic conditions led to a rapid inactivation effect. It was found that the reduction of intracellular p H caused by CO_2 led to a more lethal bactericidal effect.     

Method to assess component contribution to toxicity of complex mixtures: Assessment of puberty acquisition in rats exposed to disinfection byproducts

A method based on regression modeling was developed to discern the contribution of component chemicals to the toxicity of highly complex, environmentally realistic mixtures of disinfection byproducts(DBPs). Chemical disinfection of drinking water forms DBP mixtures.Because of concerns about possible reproductive and developmental toxicity, a whole mixture(WM) of DBPs produced by chlorination of a water concentrate was administered as drinking water to Sprague–Dawley(S–D) rats in a multigenerational study. Age of puberty acquisition,i.e., preputial separation(PPS) and vaginal opening(VO), was examined in male and female offspring, respectively. When compared to controls, a slight, but statistically significant delay in puberty acquisition was observed in females but not in males. WM-induced differences in the age at puberty acquisition were compared to those reported in S–D rats administered either a defined mixture(DM) of nine regulated DBPs or individual DBPs. Regression models were developed using individual animal data on age at PPS or VO from the DM study. Puberty acquisition data reported in the WM and individual DBP studies were then compared with the DM models. The delay in puberty acquisition observed in the WM-treated female rats could not be distinguished from delays predicted by the DM regression model, suggesting that the nine regulated DBPs in the DM might account for much of the delay observed in the WM. This method is applicable to mixtures of other types of chemicals and other endpoints.     

溶解性有机氮乙酰胺氯化生成饮用水THMs的影响因素研究

氯化消毒可以有效杀灭细菌,但同时会产生危害人体健康的消毒副产物(DBPs).溶解性有机氮(DON)是DBPs的重要前体物,为考察DON对THMs的影响,首次选取乙酰胺(AcAm)作为前体物DON的代表物质,采用Plackett-Burman和Box-Behnken方法设计试验,考察了AcAm初始浓度、加氯量、pH、温度、溴离子浓度和反应时间等因素对三卤甲烷(THMs)生成的影响.结果表明,在AcAm生成THMs的过程中,AcAm初始浓度、pH和反应温度3个因素的影响程度较小,溴离子、有效氯和反应时间3因素的影响较大,其中溴离子的影响最为显著.溴离子浓度一定时,改变有效氯的含量,生成的THMs总量变化不大,溴离子对THMs的生成有一定的催化作用,控制溴离子的浓度是减少AcAm生成THMs的有效措施.在有效氯为8.77 mg/Ｌ、溴离子为0.77 mg/Ｌ及接触时间为6.20 h的条件下,THMs存在最大生成量为45.82 μg/L.随着反应时间的推移,溴分配系数n呈上升趋势,控制消毒反应时间,是减少THMs致癌风险的有效方法.同时探讨了AcAm生成THMs的反应路径,表述了溴离子的催化作用机制.     

鲁西北太阳紫外线辐射特征分析

通过对地处鲁西北德州地区2003～2006年紫外线观测数据分析,结果表明:德州地区属于紫外线高辐射地区,紫外线辐射等级为"强"和"很强"的级别共占56%,其中"很强"的天数约占全年的1/3;在季节分布上,春季和夏季紫外线辐射最强,秋季次之,冬季最弱。