生物矿化针铁矿吸附铬的机理探讨

针铁矿在自然界中广泛存在,对重金属离子在地表的迁移和转化有重要影响.利用天然生物矿化针铁矿进行了Cr(Ⅲ)吸附研究,并利用扫描电子显微镜(SEM)和X射线光电子能谱(XPS)等对吸附后的样品进行表征,发现样品中铬的含量随着Al2O3含量的增加而增加,说明表面带负电荷的含高岭土等的粘土较针铁矿对Cr(Ⅲ)有更强的吸附能力.样品的XPS研究表明,NO3-也参与了反应,且促进了Cr(Ⅲ)的氧化.研究还发现,Cr(Ⅲ)在针铁矿上的吸附不均匀,与文献报道的情况不同.     

Photoelectrocatalytic degradation of Rose Bengal

An innovative photoelectrode, TiO2/T1 mesh electrode, was prepared by galvanostaticanodisation. The morphology and the crystalline texture of the TiO2 film on mesh electrode were examined by scanning electronic microscopy and Raman spectroscopy respectively. The examination results indicated that the structure and properties of the film depended on anodisation rate, and the anatase was the dominant component under the controlled experimental conditions. Degradation of Rose Bengal (RB) in photocatalytic (PC) and photoelectrocatalytic (PEC) reaction was investigated, the results demonstrated that electric biasing could improve the efficiency of photecatalytic reaction. The measurement results of TOC in photoelectrocatalytic degradation showed that the mineralisation of RB was complete relatively. The comparison between the degradation efficiency of RB in PEC process and that in aqueous TiO2 dispersion was conducted. The results showed that the apparent first-order rate constant of RB degradation in PEC process was larger than that in aqueous dispersion with 0.1%--0.3% TiO2 powder, but was smaller than that in aaueaus disverslon with 1.0% TiO2.     

A comparative study and evaluation of sulfamethoxazole adsorption onto organo-montmorillonites

Three organo-montmorillonites were prepared using surfactants, and their adsorption behaviors toward sulfamethoxazole（SMX） were investigated. The surfactants used were cetyltrimethyl ammonium bromide（CTMAB）, 3-（N,N-dimethylhexadecylammonio） propane sulfonate（HDAPS） and 1,3-bis（hexadecyldimethylammonio）-propane dibromide（BHDAP）. The properties of the organo-montmorillonites were characterized by X-ray diffraction, scanning electron microscopy and N2adsorption–desorption isotherm measurements. Results showed that the interlayer spacing of montmorillonite was increased and the surface area as well as the morphology were changed. Batch adsorption experiments showed that the surfactant loading amount had a great effect on the adsorption of SMX. The adsorption process was p H dependent and the maximum adsorption capacity was obtained at p H 3 for HDAPS-Mt, while CTMAB-Mt and BHDAP-Mt showed a high removal efficiency at 3–11. The adsorption capacity increased with the initial SMX concentration and contact time but decreased with increasing solution ionic strength.Kinetic data were best described by the pseudo second-order model. Equilibrium data were best represented by the Langmuir model, and the Freundlich constant（n） indicated a favorable adsorption process. The maximum adsorption capacity of SMX was 235.29 mg/g for CTMAB-Mt, 155.28 mg/g for HDAPS-Mt and 242.72 mg/g for BHDAP-Mt. Thermodynamic parameters were calculated to evaluate the spontaneity and endothermic or exothermic nature. The adsorption mechanism was found to be dominated by electrostatic interaction,while hydrophobic interaction played a secondary role.     

Synthesis and characterisation of potassium polytitanate for photocatalytic degradation of crystal violet

Potassium titanate nanostructures were synthesised by hydrothermal treatment of TiO2 （P25） in KOH and H2O2. As-produced powders were characterised by scanning electron microscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy, X-ray diffraction, and nitrogen adsorption-desorption methods. Longitudinally-oriented-wire-like structures with a length up to several micrometres and diameters ranging from 10 to 30 nm were obtained. Larger size fibrous nanowires resulting from the hydrotherrnal treatment showed high affinity in adsorbing crystal violet （CV）, which was mainly due to their high surface area. The photocatalytic bleaching of CV solution revealed that the wires are photoactive under ultraviolet light irradiation. Macroporous nanowires are considered as effective adsorbents of CV, capable of photocatalvtic degradation, and they can be easily separated from the solution by settling.     

Graphene TiO2 nanocomposites with high photocatalytic activity for the degradation of sodium pentachlorophenol

A series of graphene–TiO2photocatalysts was synthesized by doping TiO2 with graphene oxide via hydrothermal treatment. The photocatalytic capability of the catalysts under ultraviolet irradiation was evaluated in terms of sodium pentachlorophenol（PCP-Na） decomposition and mineralization. The structural and physicochemical properties of these nanocomposites were characterized by X-ray diffraction, N2adsorption–desorption, transmission electron microscopy, scanning electron microscopy, Ultraviolet–visible diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, electron paramagnetic resonance spectra, and Fourier-transform infrared spectroscopy. The graphene–TiO2nanocomposites exhibited higher photocatalytic efficiency than commercial P25 for the degradation of PCP-Na, and 63.4% to 82.9% of the total organic carbon was fully mineralized. The improved photocatalytic activity may be attributed to the accelerated interfacial electron-transfer process and the significantly prolonged lifetime of electron-hole pairs imparted by graphene sheets in the nanocomposites. However,excessive graphene and the inhomogeneous aggregation of TiO2 nanoparticles may decrease photodegradation efficiency.     

Effects of shear force on formation and properties of anoxic granular sludge in SBR

This paper reports the effects of shear force on anoxic granular sludge in sequencing batch reactors （SBR）. The study was carried out in two SBRs （SBR1 and SBR2） in which sodium acetate （200mg COD·L^-1） was used as the sole substrate and sodium nitrate （40 mgNO3-N·L^-1） was employed as the electron acceptor. The preliminary objective of this study was to cultivate anoxic granules in the SBR in order to investigate the effects of shear force on the formation of anoxic granular sludge and to compare the properties of anoxic sludge in the SBR. This study reports new results for the values of average velocity gradient, a measure of the applied shear force, which was varied in the two SBRs （3.79 s^-1 and 9.76 s^-1 for SBR1 and SBR2 respectively）. The important findings of this research highlight the dual effects of shear force on anoxic granules. A low shear force can produce large anoxic granules with high activity and poor settling ability, whereas higher shear forces produce smaller granules with better settling ability and lower activity. The results of this study show that the anoxic granulation is closely related to the strength of the shear force. For high shear force, this research demonstrated that： 1） granules with smaller diameters, high density and good settling ability were formed in the reactor, and 2） granular sludge formed faster than it did in the low shear force reactor （41days versus 76 days）. Once a steady-state has been achieved, the nitrate and COD removal rates were found to be 98% and 80%, respectively. For low shear force, such as was applied in SBR1, this research demonstrated that： 1） the activity of anoxic granular sludge in low shear force was higher than that in high shear force, 2） higher amount of soluble microbial products （SMPs） were produced, and 3） large pores were observed inside the larger granules,which are beneficial for nitrogen gas diffusion. Electron microscopic examination of the anoxic granules in both reactors showed that the morphology of the granules was ellipsoidal with a clear outline. Coccus and rod-shaped bacteria were wrapped by filamentous bacteria on the surface of granule.     

Removal of clofibric acid from aqueous solution by polyethylenimine-modified chitosan beads

Polyethylenimine （PEI）-modified chitosan was prepared and used to remove clofibric acid （CA） from aqueous solution. PEI was chemically grafted on the porous chitosan through a crosslinking reaction, and the effects of PEI concentration and reaction time in the preparation on the adsorption of clofibric acid were optimized. Scanning electron microscopy （SEM） showed that PEI macromolecules were uniformly grafted on the porous chitosan, and the analysis of pore size distribution indicated that more mesopores were formed due to the crosslinking of PEI molecules in the macropores of chitosan. The PEI-modified chitosan had fast adsorption for CA within the initial 5 h, while this adsorbent exhibited an adsorption capacity of 349 mg· g^-1 for CA at pH 5.0 according to the Langmuir fitting, higher than 213 mg· g^-1 on the porous chitosan. The CA adsorption on the PEI- modified chitosan was pH-dependent, and the maximum adsorption was achieved at pH 4.0. Based on the surface charge analysis and comparison of different pharmaceu- ticals adsorption, electrostatic interaction dominated the sorption of CA on the PEI-modified chitosan. The PEI- modified chitosan has a potential application for the removal of some anionic rnicropollutants from water or wastewater.     

Recovery of NH 4 + by corn cob produced biochars and its potential application as soil conditioner

NH4^＋ ion, a main pollutant in aquatic systems, not only causes eutrophication in rivers and lakes but also contributes to fish toxicity. In this study, an eco-friendly biosorbent was prepared from the pyrolysis of corn cob, a low-cost agricultural residue. The biochars produced by pyrolysis of corn cob at 400℃ and 600℃ were characterized and investigated as adsorbents for NH4＋ -N from an aqueous solution. The biochars were characterized through elemental analysis, Brunauer-Emmett-Teller-N2 surface area analysis, scanning electron microscopy, and Fourier transform infrared spectroscopy. Batch experiments were conducted to investigate the NH4＋ adsorption process of the corn cob biochars. The Freundlich isotherm model fitted the adsorption process better than the Langmuir and Dubinin-Radushkevich isotherm models. Moreover, the adsorption process was well described by a pseudo-second-order kinetic model. Results of thermodynamic analysis suggested that adsorption was a nonspontaneous exothermic process. Biochars produced at 400℃ had higher adsorption capacity than those produced at 600℃ because of the presence of polar functional groups with higher acidity. The exhausted biochar can be potentially used as soil conditioner, which can provide 6.37 kg NH4＋-N-t^-1 （N fertilizer per ton of biochar）.     

Morphology of single inhalable particle inside public transit biodiesel fueled bus

In an urban-transit bus,fueled by biodiesel in Toledo,Ohio,single inhalable particle samples in October 2008 were collected and detected by scanning electron microscopy and energy dispersive X-ray spectrometry(SEM/EDS).Particle size analysis found bimodal distribution at 0.2 and 0.5 μm.The particle morphology was characterized by 14 different shape clusters:square,pentagon,hexagon,heptagon,octagon,nonagon,decagon,agglomerate,sphere,triangle,oblong,strip,line or stick,and unknown,by quantitative order.The square particles were common in the samples.Round and triangle particles are more,and pentagon,hexagon,heptagon,octagon,nonagon,decagon,strip,line or sticks are less.Agglomerate particles were found in abundance.The surface of most particles was coarse with a fractal edge that can provide a suitable chemical reaction bed in the polluted atmospheric environment.The three sorts of surface patterns of squares were smooth,semi-smooth,and coarse.The three sorts of square surface patterns represented the morphological characteristics of single inhalable particles in the air inside the bus in Toledo.The size and shape distribution results were compared to those obtained for a bus using ultra low sulfur diesel.     

Paper sludge as a feasible soil amendment for the immobilization of Pb^2＋

The possibility of amending Pb 2+ contaminated soil (S) with paper sludge (P) was investigated through adsorption and desorption experiments. The adsorption process of Pb 2+ in soil containing paper sludge (SP) could be well described by pseudo second-order kinetic model and the Langmuir isotherm model. After P addition, the equilibrium time decreased greatly (from 28 to 8 hr) and the Pb 2+ maximum adsorbed amount (Q max ) increased by a factor of more than three to 102.04 mg/g. Q max reached its maximum as...