吹脱-捕集气相色谱法测定底质中易挥发性有机物

研究并建立了利用吹脱－捕集气相色谱法测定底质中易挥发性有机物的分析方法。该方法对底质中２５种易挥发性有机物进行测定。方法回收率在９６％－１０５％,最低检出浓度在０．３－１４．５μｇ／ｋｇ,变异系数在２．７％－５．３％。     

鳌山湾沉积物间隙水营养盐的含量及其分布

根据2004年6月中旬鳌山湾的调查资料,分析了鳌山湾海域5项营养盐NO2-N,NO3-N,NH4-N,PO4-P,SiO3-Si的浓度分布特征。得知间隙水中NO2-N浓度分布在1.01￣48.86μmol·L-1,NO3-N为2.1￣108.16μmol·L-1,NH4-N为3.02￣18.28μmol·L-1,PO4-P为0.13￣1.42μmol·L-1,SiO3-Si为70￣168μmol·L-1之间,并将间隙水浓度与底层水相比较。结果表明:间隙水营养盐的浓度远远高于底层水营养盐的浓度,揭示了间隙水与上覆水体之间营养物质的交换并不是十分强烈。     

Acoustic Observations of Bottom Surge From Dredged Material Discharge in the Open Ocean

Abstract

Bottom surges generated from dredged material discharges in the open ocean have been observed using high frequency acoustic concentration profilers in several field studies during the past five years. the locations, water depths, bottom slopes, oceanographic conditions, and dredged material composition differed from study to study. Observed surges at three dredged material disposal sites may develop more than one surge peak for a single discharge. for water depths of the order of 10 m, surge height of the leading peak was estimated to be about one quarter of the water depth. for water of greater depth, of the order of 100 m, surge height reached 70 m, about 70% of the water depth. Surge height is established instantaneously when dredged material hits the bottom, and remains relatively constant as the surge advances horizontally. Total surge length reached 150 m for water depths of 10 m when measured from the impact point to the leading edge. for water depths of more than 100 m, the surge length reached more than 100 m. Length of the leading surge peak was as large as 45 m at this water depth.

Dimensional analysis was applied to relate the surge height of the leading surge peak to discharge parameters and oceanographic conditions. Results showed that the ratio of surge height to water depth was proportional to 1/10 power of the ratio of discharge volume to the third power of water depth.     

Enrichment of elements in industrial waste incineration bottom ashes obtained from three different types of incinerators,as studied by ICP-AES and ICP-MS

The elemental composition of the industrial waste incineration bottom ash (IWIBA) samples collected from three different types of incinerator with different kinds of wastes were compared. The major-to-ultratrace elements in the IWIBA samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). As a result, ca. 40 elements in the concentration range from milligrams per gram to submicrograms per gram could be determined with relative standard deviations of less than 5%. The IWIBA sample from petrochemical wastes contained lower concentrations of the elements, because fewer mineral constituents were contained in the input waste materials. On the contrary, the elemental concentrations in the IWIBA sample from industrial solid wastes provided the highest values for most elements, while the elemental compositions of the IWIBA sample from food wastes were similar to those of municipal solid waste incineration bottom ash. In addition, it was found from the analytical results that the levels of various heavy metals such as Cr, Mn, Fe, Ni, Cu, As, Zr, Mo, Sb, Ba, and Pb were higher in the IWIBA samples than in municipal solid waste incineration bottom ash. The enrichment factors of the elements in the IWIBA samples were estimated from the analytical results to compare the elemental distributions in incineration bottom ashes in relation to their mining influence factors, which are the indices for human use of the elements.     

Impact of variable nitrogen fertilisation on arthropods in cotton in Georgia, USA

Reducing fertiliser applications can reduce production costs for cotton (Gossypium hirsutum L.) growers, as well as nitrogen (N) leaching into the soil and contamination of surface and ground water. But altered N fertilisation may also affect pests and their natural enemies. In this study, plots with four different levels of fertiliser input (0, 45, 90 and 135 kg ha⁻¹ N) were used to investigate the influence of N on cotton pest and beneficial arthropod populations, and on cotton yield in Tifton, GA, USA. We predicted that (1) N fertilisation will correlate positively with cotton plant growth; (2) increased N fertilisation will increase pest populations because plants with more N will be more nutritious for and attractive to herbivores; (3) populations of beneficial arthropods and predation of pests will decline with increased N fertilisation because of reduced plant signaling; (4) increased N fertilisation will increase pest mortality due to parasitoids because of increased host quality. Cotton plant growth was enhanced by N fertilisation but yield was unaffected. N fertilisation significantly affected some pest arthropods but inconsistently. Mirids were most abundant in the high N treatment in 1 year of the study and cotton aphids were most abundant in the highest N treatment in the other year of the study. Arthropod predators were generally more abundant in the high N treatment but only spiders and Geocoris spp. were significantly affected by N treatment, with highest numbers present in the highest N treatment but the significant differences were each only in a single year. The greatest mortality of sentinel pest eggs (Spodoptera exigua) due to predation occurred under low N conditions. N fertilisation had no significant effects on parasitism of feral or sentinel caterpillars.     

Bench-scale synthesis of zeolite A from subbituminous coal ashes with high crystalline silica content

In this present work, fly ash and bottom ash with high crystalline silica content were obtained from the coal-fired boilers within the paper industries in Thailand. These coal ashes were used as the basic raw materials for synthetic zeolite production. The crystal type and crystallinity, specific surface area and pore size, and textural properties of zeolite products were characterized by using X-ray diffraction spectroscopy (XRD), N₂ sorption analysis, and Scanning Electron Microscopy (SEM), respectively. It was found that sodalite octahydrate was selectively formed via the direct conventional (one-step) synthesis, whereas through a two-step, sodium silicate preparation and consecutive zeolite A synthesis process, 94 and 72 wt.% zeolite A products could be produced from the fly ash and bottom ash, respectively. The cation-exchange capacity (CEC) of fly ash and bottom ash-derived zeolite A products were closely similar to that of the commercial grade zeolite A.     

Current status and perspectives of accelerated carbonation processes on municipal waste combustion residues

The increasing volumes of municipal solid waste produced worldwide are encouraging the development of processes to reduce the environmental impact of this waste stream. Combustion technology can facilitate volume reduction of up to 90%, with the inorganic contaminants being captured in furnace bottom ash, and fly ash/APC residues. The disposal or reuse of these residues is however governed by the potential release of constituent contaminants into the environment. Accelerated carbonation has been shown to have a potential for improving the chemical stability and leaching behaviour of both bottom ash and fly ash/APC residues. However, the efficacy of carbonation depends on whether the method of gas application is direct or indirect. Also important are the mineralogy, chemistry and physical properties of the fresh ash, the carbonation reaction conditions such as temperature, contact time, CO₂ partial pressure and relative humidity. This paper reviews the main issues pertaining to the application of accelerated carbonation to municipal waste combustion residues to elucidate the potential benefits on the stabilization of such residues and for reducing CO₂ emissions. In particular, the modification of ash properties that occur upon carbonation and the CO₂ sequestration potential possible under different conditions are discussed. Although accelerated carbonation is a developing technology, it could be introduced in new incinerator facilities as a “finishing step” for both ash treatment and reduction of CO₂ emissions.