温度对生物强化除磷工艺反硝化除磷效果的影响

以处理城市污水的中试规模生物强化除磷A2/O活性污泥工艺系统为研究对象,考察了温度对系统COD去除和脱氮除磷效果的影响,特别是温度对活性污泥反硝化除磷性能的影响.结果表明,当温度从(30.9±0.8)℃降低到(9.1±0.6)℃时,A2/O系统的脱氮除磷效果显著下降,系统对TN和TP的污泥去除负荷明显下降.通过污泥反硝化除磷活性实验发现,随着温度的降低,系统中活性污泥的最大厌氧释磷速率、最大好氧吸磷速率和最大缺氧吸磷速率都降低.活性污泥中反硝化除磷菌(DPB)占聚磷菌(PAOs)总量的比例随温度降低稍有下降,但平均值仍维持在47.5％左右.用阿伦尼乌斯公式对实验结果进行拟合,得到系统中活性污泥聚磷菌厌氧释磷反应活化能Ea1为148.0 kJ· mol-1,聚磷菌好氧吸磷反应活化能Ea2为228.8 kJ·mol-1,发生在缺氧条件下反硝化除磷菌的吸磷反应活化能Ea3为315.8 kJ·mol-1.对不同温度下污泥絮体粒径分析结果表明,随温度降低,粒径分布更加集中,系统中活性污泥絮体颗粒平均粒径减小,不利于污泥絮体内部反硝化除磷缺氧微环境的形成.     

高岭土负载纳米Fe/Ni同时去除水中Cu2+和NO3-

工业废水常含有不同污染物如重金属离子和无机阴离子,而如何有效去除复合污染物就成为环境科学前沿研究的挑战性课题.这些污染物因化学性质不同而导致去除机理和途径也不同.本文采用合成高岭土负载纳米双金属Fe/Ni(K-Fe/Ni)同步去除水中Cu2+和NO-3.结果表明K-Fe/Ni能有效去除水中Cu2+和NO-3,但它们的去除效果却会相互受到影响.在Cu2+浓度为200mg·L-1时,NO-3的去除率达到42.5%;而未加入Cu2+时,NO-3的去除率仅有26.9%,说明Cu2+的存在提高了NO-3降解效率.同样,水中NO-3的存在也影响Cu2+的去除(Cu2+去除率从99.7%降到96.5%).但NO-3浓度对去除Cu2+的影响小于Cu2+浓度对NO-3的影响.通过BET比表面积、X射线衍射(XRD)、扫描电镜(SEM)、X射线能量散射(EDS)和X射线光电分析(XPS)对K-Fe/Ni表征的结果显示,反应后K-Fe/Ni的表面存在铁的氧化物、Ni0和被还原的Cu0.基于以上结果,我们发现K-Fe/Ni同步去除水中Cu2+和NO-3的机理是:高岭土负载下的纳米Fe0作为还原剂,在Ni0的催化产氢作用下将Cu2+还原成Cu0并沉积在K-Fe/Ni上而形成纳米Fe/Ni/Cu三金属催化剂,从而加速催化水中NO-3降解.     

呼和浩特市可镇污水处理厂工程设计

呼和浩特市可镇污水处理厂近期建设规模1.0×104m3/d,远期总规模2.5×104m3/d。污水处理主体工艺采用组合式A2/O生化池+砂滤,污泥处理采用污泥贮池+带式浓缩脱水一体机,尾水采用液氯消毒,设计出水水质执行GB 18918—2002《城镇污水处理厂污染物排放标准》一级A排放标准。介绍了该工程的工艺流程、设计参数,总结分析了工艺设计的技术特点。同时阐述了针对低温条件下的运行保障措施和要求,为寒冷地区同类污水处理厂的设计提供参考和借鉴。     

FY2 号气象卫星估算地面太阳辐射研究

综合考虑太阳因素、地形因素、地表积雪覆盖情况、云量以及非均质大气对太阳辐射的影响,基于FY2 号静止卫星构建晴空太阳总辐射计算模型,并利用山西省3 个辐射观测站2011 年逐时、逐日、逐月太阳总辐射观测资料对其估算结果进行检验。研究结果显示：逐时误差在±1 MJ·m^-2之间,逐日误差在±5 MJ·m^-2之间,表明模型计算的太阳辐射误差较小,稳定性较好;逐月误差结果显示,三个站模拟值都大于实测值,且误差趋势一致,均表现为冬季误差高于夏季;进一步对模拟值和实测值进行相关性分析,三站线性拟合度均在0.86～0.92 之间,且相关系数均达到显著相关水平,表明模型计算的太阳辐射准确性和精度较高,且在数值拟合上较好地反映了实际的太阳总辐射量,证实该模型应用于FY2 号气象卫星的可行性。     

金属离子对δ-MnO2 去除对叔辛基酚抑制作用的研究

研究了pH 4.0的水溶液中各种金属离子对合成的δ-MnO2去除对叔辛基酚(4-t-OP)的影响.实验表明反应150 min时,δ-MnO2对4-t-OP的去除率达到100%,但当反应体系中含有金属离子时,去除效果受到抑制.抑制效果随金属离子浓度的增加而增大,并随金属离子的不同表现出较大的差异.在pH 4.0条件下,Pb2+和Mn2+的抑制效果最强,其次为过渡金属离子,再次是碱土金属离子,而碱金属离子基本上不产生抑制作用.还比较了δ-MnO2对多种金属离子的吸附能力,其对Pb2+的吸附作用最强,在其余的金属离子中,对过渡金属离子的吸附量稍大于碱土金属离子.结果表明,金属离子所产生抑制作用的源于其占据了δ-MnO2表面反应位点并与4-t-OP形成竞争,而抑制作用大小的差异主要来源于δ-MnO2与金属离子间吸附作用强弱的差别,MnO2表面结构的变化,以及溶液中自由态金属离子的分布比例及其离子半径的不同.     

UV和H2 O2联合消毒灭活饮用水中大肠杆菌研究

以大肠杆菌为研究对象,对单独紫外线(UV)、H2O2及两者不同组合方式的灭活效果进行了分析.结果表明,单独H2O2对大肠杆菌基本无灭活效果,加入浓度为20 mg·L-1的H2O2接触时间为30 min时,灭活率仅为0.02个对数级;单独UV工艺可在一定程度上灭活大肠杆菌,紫外线剂量为10 mJ·cm-2时,灭活率可达到4.51个对数级.紫外线和H2O2联合消毒在一定程度上提高了消毒效果,且不同的组合方式对灭活效果有很大的影响.先UV后H2O2消毒效果优于先H2O2后UV,当紫外线剂量为5 mJ·cm-2时,加入H2O2分别反应2.5、5、10、20 min后,两者的灭活率分别较单独UV消毒增加0.09、0.35、0.38、0.68和0.01、0.07、0.14、0.53个对数级.而UV与H2O2同时消毒效果优于UV与H2O2顺序消毒,当紫外线剂量为5 mJ·cm-2时,加入H2O2反应20 min后,灭活率较UV-H2O2和H2O2-UV工艺分别增加了0.43和0.58个对数级.随着紫外线强度的增加,大肠杆菌的灭活效果不断提高.     

泥龄对A~2O工艺去除多环麝香的影响

研究了A2O工艺不同污泥龄(Sludge retention time,SRT)条件下中佳乐麝香(Galaxolide,HHCB)与吐纳麝香(Tonalide,AHTN)的去除和迁移的变化情况。采用固相萃取与气相质谱联用的方法对各池中水相与泥相中HHCB和AHTN的浓度进行分析。结果发现:A2O工艺对HHCB的去除效果好于AHTN。高SRT条件(15,20 d)下HHCB、AHTN的总去除率明显小于低SRT条件(5,10 d)下的总去除率。     

Adsorption of 2-mercaptobenzothiazole from aqueous solution by organo-bentonite

The adsorption behavior of 2-mercaptobenzothiazole onto organo-bentonite was investigated.Natural bentonite from Gaozhou in Guangdong Province,China was collected.Organo-bentonite was prepared by intercalation of cetyltrimethyl ammonium bromide into the natural bentonite.The physicochemical properties of the prepared organo-bentonite were characterized by X-ray diffraction,N2 adsorption-desorption isotherm and Fourier transform infrared spectroscopy.The results showed that montmorillonite is the main component of the natural bentonite.The basal spacing of the natural bentonite is 1.47 nm,which increased to 1.98 nm on intercalation with cetyltrimethyl ammonium bromide.Moreover,both the surface area and pore volume increased with intercalation.Clear CH2 stretching(3000-2800 cm-1) and scissoring(1480-1450 cm-1) modes of the intercalated surfactants were observed for organobentonite.Compared with the pseudo first-order kinetic model,the pseudo second-order kinetic model is more suitable to describe the adsorption kinetics of 2-mercaptobenzothiazole onto organo-bentonite.The adsorption capacity of 2-mercaptobenzothiazole onto organo-bentonite increased with increasing initial concentration of 2-mercaptobenzothiazole,but decreased with increasing adsorbent dosage.The adsorption isotherm of 2-mercaptobenzothiazole onto organo-bentonite fits well with the Langmuir model.The maximum adsorption capacity of organo-bentonite for 2-mercaptobenzothiazole was 33.61 mg/g,indicating that organo-bentonite is a promising adsorbent for 2-mercaptobenzothiazole.     

Effects of physical and chemical characteristics of surface sediments in the formation of shallow lake algae-induced black bloom

Surface sediments are closely related to lake black blooms. The dissolved oxygen （DO） distribution and its penetration depth in surface sediments as well as the migration and transformation of redox sensitive elements such as Fe and S at the sediment-water interface are important factors that could influence the formation of the black bloom. In this study, dredged and undredged sediment cores with different surface properties were used to simulate black blooms in the laboratory. The Micro Profiling System was employed to explore features of the DO and ∑H2S distribution at the sediment-water interface. Physical and chemical characteristics in sediments and pore waters were also analyzed. The results showed that sediment dredging effectively suppressed the black blooms. In the undredged treatment, DO penetration depth was only 50 μm. Fe^2＋ concentrations, ∑H2S concentrations, and ∑H2S production rates were remarkably higher in surface sediments and pore waters compared to control and dredged treatments. Furthermore, depletion of DO and accumulation of Fe^2＋ and ∑H2S in surface sediments and pore waters provided favorable redox environments and necessary material sources for the blooms. The study results proved that physical and chemical characteristics in surface sediments are important factors in the formation of the black bloom, and could provide scientific guidance for emergency treatment and long-term pre-control of black blooms.     

Formic acid as an alternative reducing agent for the catalytic nitrate reduction in aqueous media

Formic acid was used for the nitrate reduction as a reductant in the presence of Pd:Cu/γ-alumina catalysts. The surface characteristics of the bimetallic catalyst synthesized by wet impregnation were investigated by SEM, TEM-EDS. The metals were not distributed homogeneously on the surface of catalyst, although the total contents of both metals in particles agreed well with the theoretical values. Formic acid decomposition on the catalyst surface, its influence on solution pH and nitrate removal efficacy was investigated. The best removal of nitrate (50 ppm) was obtained under the condition of 0.75 g/L catalyst with Pd:Cu ratio (4:1) and two fold excess of formic acid. Formic acid decay patterns resembled those of nitrate removal, showing a linear relationship between kf (formic acid decay) and k (nitrate removal). Negligible amount of ammonia was detected, and no nitrite was detected, possibly due to buffering effect of bicarbonate that is in situ produced by the decomposition of formic acid, and due to the sustained release of H2 gas.