内排压脚与边坡稳定性的关系

为了研究边坡角及边坡形状与边坡稳定性的关系,采用有限元软件ANSYS模拟了不同边坡角对应的稳定系数,以及不同平盘宽度和压脚高度所形成的等储备强度边坡的稳定系数。模拟中假设材料符合相关联的理想弹塑性本构关系,强度准则符合Drucker-Prager准则,用计算收敛性作为边坡稳定性的准则,用强度折减法得出边坡的稳定系数。为了形成等储备强度边坡,由下到上分步骤进行压脚。先在平面边坡最下台阶压脚,这样提高了边坡稳定系数,在边坡进入临界状态时,最下两台阶的塑性状态相同,则压脚停止;再在最下两台阶同时压脚,在边坡进入临界状态时,最下3个台阶的塑性状态相同,则压脚停止;以此类推,在最下边n个台阶同时压脚,在边坡进入临界状态时,压到与第n+1个台阶的塑性状态相同为止。结果表明,边坡总是从坡脚开始形成塑性区,在重力加载过程中,塑性区以弧形条带向坡顶扩展,形成滑带。最有效的内排压脚是从最下台阶开始形成等储备强度边坡的压脚。     

天津市夏季PM10浓度及组成元素垂直分布特征

通过天津市气象局大气边界层观测站高255 m的气象铁塔,获得了10m、40m、120m和220 m 4个高度共80个PM10样品,分析了PM10的日均质量浓度及其元素的垂直分布特征.结果表明,4个高度处PM10质量浓度时序变化基本一致;PM10质量浓度及其组成元素总量随高度增加递减;10 m、40m和120m3个高度处的PM10质量浓度时间序列分布的相关性较好,组分分歧系数较小,而220 m处的PM10质量浓度时间序列分布与其他3个高度处的相关性较差,组分分歧系数较大.样品中元素质量浓度由高到低依次是Si、Al、Ca、Fe、Na、Mg、K、Zn、Ti、Cu、Mn、Pb、Cr、Ni、Co、V、As、Cd和Hg.其中,Si、Al、Na、K质量分数随高度变化不大;Ca、Fe、Mg质量分数随高度增加递减明显;Zn、Cu、Mn、Pb、Cr在10m、40m和120 m3个高度处质量分数接近,而在220m处明显降低;Ti元素在4个高度处的质量浓度接近,质量分数总体上随高度增加递增;Ni、Co、V、As、Cd、Hg质量分数随高度的变化不同,其中与燃煤有密切关系的Hg在120 m处质量分数明显高于其他高度处,而在220m处最低.Al、Fe、Na、K等元素相对富集因子小于或接近1,其质量浓度与PM10质量浓度时序分布的相关性较好,其中Al、Na相关系数随高度增加显著递减;Zn,Cu、Pb、Cr、As、Ni的相对富集因子显著大于1,其质量浓度与PM10质量浓度时序分布的相关性较差,相关系数随高度增加变化不大.     

储罐硫腐蚀产物标志性气体的监测

含硫油品储罐内的腐蚀产物与油品中的活性硫反应生成硫化物,而此类硫腐蚀产物氧化自燃是导致储油罐发生火灾、爆炸事故的重要原因.通过试验考察了氧气体积比对硫腐蚀产物氧化自燃过程的影响,探索了铁锈模拟物在氧化过程中SO2气体的释放规律.结果表明:氧气浓度越高,硫腐蚀产物的自燃危险性越大;随着O2浓度增加,氧化反应中SO2的浓度越大,SO2气体析出速度越快,当氧化反应的温度为40℃时,SO2气体浓度达到最大.     

生物表面活性剂产生菌处理水体石油污染物的研究

为研究水体石油污染物的生物处理方法,通过富集培养、蓝色凝胶平板分离初筛、摇瓶复筛等方法从长期被石油污染的油泥中筛选生物表面活性剂产生菌.采用薄层层析显色法和红外光谱法鉴定该菌所产表面活性剂种类,测定表面活性剂的乳化性能、表面张力和临界胶束浓度等性能,并对菌株降解水体石油污染物的影响因素及效果进行了研究.结果表明,筛选出的生物表面活性剂高产菌株LJ2所产表面活性剂为糖脂,其乳化指数为33％,25℃下可将水的表面张力从71.14 mN/m降至27.22 mN/m,临界胶束质量浓度为5 mg/L;当表面活性剂水溶液质量浓度为100 mg/L时,其乳化指数可达50％.温度、降解时间以及NaCl质量分数对菌株LJ2处理水体石油污染效果影响很大.在34℃条件下处理5d,菌株LJ2对质量浓度为2 g/L的水体石油污染物的降解率高达99.5％.研究表明,生物表面活性剂产生菌L J2对水体石油污染物有良好的降解效果,而且该菌还对水体中较高浓度的NaCl有一定的耐受性.     

落石冲击作用下架设油气管道响应分析

针对影响油气管道安全运营的落石冲击问题,基于弹塑性力学、Cowper-Symonds本构模型和有限元方法,建立了球形落石冲击油气管道的计算模型,对管道动态响应过程进行了数值模拟。对冲击速度、落石半径、管道内压力和落石冲击位置进行了参数敏感性分析,研究了各参数对管道冲击变形的影响规律。结果表明:落石的冲击能量主要用于管道塑性变形;冲击过程中,落石与管道的接触区域由初始的椭圆斑逐渐变成了椭圆环;管道塑性变形随着冲击速度和落石半径的增大而增大,随内压和落石偏移度的增大而减小。该研究工作为油气管道的安全评价及防护工程的设计提供了参考依据,对保障油气安全运输具有重要的工程意义。     

绿灯倒计时信号对驾驶行为的影响

为揭示绿灯倒计时信号对交叉口交通安全的影响,针对不同交通负荷与信号控制方式下的驾驶行为开展研究。选择大连市内的倒计时信号交叉口与非倒计时信号交叉口各2处,开展车辆行驶速度及不良驾驶行为调查。用数理统计方法,对比分析2类交叉口在平峰与高峰时段的车辆行驶速度特性,同时对比分析上述不同条件下闯黄灯及违规变道行为的发生数量。研究表明,绿灯倒计时信号在绿灯时间末期,会诱发一部分驾驶员加速行驶通过交叉口;绿灯倒计时信号在平峰时段对闯黄灯行为数量的影响较小,而对违规变道行为的数量有显著影响。     

Influence of concentration distribution of hydrogen in air on measured flammability limits

There is a clear difference between exiting data on the measured flammability limits of hydrogen-air mixture. The non-uniformity of concentration distribution of hydrogen in air is a contributor to deviations of the upper flammability limit (UFL) and the lower flammability limit (LFL) measured in different experiments. This paper presents a numerical model to simulate the gas mixing process from start to stability, to predict the concentration distribution, and to research the influence of concentration distribution of hydrogen in air on measured UFLs and LFLs. The commercial software package Fluent was used to carry out the numerical simulation for the concentration distribution of hydrogen in air in the vessels with length-to-diameter ratios (L: D) of 1:1, 3:1, 5:1 and 7:1 respectively. Based on the numerical simulation and analysis, the influence of concentration distribution on measured flammability limits was demonstrated for hydrogen in air in the vessel. It is found that the deviations of measured flammability limits of hydrogen in air are the minimum in the vessel with length-to-diameter ratio of 1:1, and augment with the augmentation of vessel length-to-diameter ratio. Moreover, it is presented that the deviations of measured flammability limits of hydrogen in the center of the vessel are lower than that in the top and the bottom.     

Gas flame acceleration in long ducts

In many practical situations, a flame may propagate along a pipe, accelerate and perhaps transform into a devastating detonation. This phenomenology has been known, more or less qualitatively, for a long time and mitigation techniques were proposed to try and avoid this occurrence (flame arresters, vents,...). A number of parameters need to be known and in particular the “distance to detonation” and more generally the flame acceleration characteristic scales. Very often, the ratio between the detonation run-up distance and the pipe diameter is used without any strong justification other that using a non-dimensional parameter (L/D). In this paper, novel experimental evidence is presented on the basis of relatively large scale experiments using 10 cm and 25 cm inner diameter duct with a length between 7 and 40 m. Homogeneous C₂H₄-air, CH₄-air, C₃H₈-air and H₂-air mixtures were used and different ignition sources. The interpretation suggests that the self-acceleration mechanism of the flame may be much better represented by flame instabilities than by turbulence build-up. One consequence would be that the maximum flame velocity and, following, the maximum explosion overpressure, would be rather linked with the run-up distance than with the L/D ratio.     

The Kinetics of Interesterfication on Waste Cooking Oil (Sunflower Oil) for the Production of Fatty Acid Alkyl Esters using a Whole Cell Biocatalyst (Rhizopus oryzae) and Pure Lipase Enzyme

Recent research and technology have provided promising outcomes to rely on biodiesel as the alternative and conventional source of fuel. The use of renewable sources constitutes the main stream of research. Waste Cooking Oil (WCO) was used for biodiesel production in this study. Lipase enzyme producing fungi Rhizopus oryzae 262 and commercially available pure lipase enzyme were used for comparative study in the production of FAAE. The whole cell biocatalyst and pure enzyme were immobilized using calcium alginate beads. It was prepared by optimizing with different molar ratios of calcium chloride and different percent sodium alginate. Entrapment immobilization was done for whole cell biocatalyst. PE was also immobilized by entrapment for the transesterification reaction. Four different solvents methanol, ethanol, n-propanol, n-butanol were used as the acyl acceptors. The reaction parameters like temperature, molar ratio, reaction time, and amount of enzyme to be used were also optimized for methanol alone. The same parameters were adopted for the other acyl acceptors too. Among the different acyl acceptors, methanol whose reaction parameters were optimized showed maximum conversion of triglycerides to FAAE - 94% with PE and 84% with WCB. On the whole, PE showed better catalytic converting ability with all the acyl acceptor compared to WCB, further study, it was observed that three consecutive and reversible reactions occurred in the interesterification of triglycerides. So, a kinetic model based on Michaelis-Menten equation with competitive substrate inhibition was used to find the maximum reaction rate V_i for the four solvents using pure enzyme and WCB.     

基于卫星遥感的浙北平原气溶胶光学特性长期变化分析

利用MOD04 C051气溶胶产品,以浙江北部平原为主要研究区,开展区域气溶胶光学特性长期(2000年3月—2013年12月)变化分析.长期逐月时间序列显示,区域气溶胶光学特性具有年内周期性变化规律,AOD(Aerosol Optical Depth)峰值多出现在5月或6月;Angstrom Exponent(α指数)峰值多出现在3月或4月.在空间分布上,研究区中部地区气溶胶污染较重且粗粒子成分较高.研究区气溶胶光学特性长期变化特征主要体现在:1气溶胶污染总体减轻但细粒子成分增加,复合污染加重;2008年以来区域AOD年均值总体呈下降趋势;2007—2013年α指数年均值显著高于2000—2006年;区域α指数月均值增长趋势显著,近14年的总倾向率为0.125(p0.05);2AOD和α指数的季节差异呈减小趋势,AOD的季节变化规律由2000年的春夏≈冬秋转变为2013年的春冬秋≥夏;α指数虽仍以夏秋季高于冬春季,但春秋两季α指数相对增大;3以污染较轻的湖州市和污染较重的嘉兴市为例的原因分析显示,AOD变化与SO2排放量具有一定相关性,α指数变化与民用汽车拥有量变化趋势一致,相关性较高.