2020年成都市典型臭氧污染过程特征及敏感性

2020年4月24日至5月6日成都市臭氧(O3)和细颗粒物(PM2.5)复合污染过程期间,在成都市城区开展大气臭氧及其前体物(NO,、VOCs)和气象参数观测实验,基于观测数据采用OBM模型对市区臭氧敏感性和主控因子进行识别,并采用PMF模型对关键VOCs物种进行来源解析.结果表明,臭氧超标日各污染物浓度均有所上升,VOCs物种中芳香烃和含氧(氮)化合物上升幅度较大;成都市城区O3超标天对应的臭氧处于显著VOCs控制区,芳香烃和烯烃对O3生成最为敏感,且存在削减NOx的不利效应;结合VOCs来源解析,城区VOCs主要来源:移动源(22.4％)、餐饮及生物质燃烧源(21.8％)、工业源(15.1％)和溶剂使用源(9.3％),臭氧超标天溶剂使用源、餐饮及生物质类燃烧源贡献率明显上升.成都市城区春季应以VOCs减排为重点,并加大芳香烃和烯烃相关源控制力度.     

曝气生物滤池内的自养反硝化作用

采用多孔介质——火山岩为载体的上向流曝气生物滤池(BAF),研究了限制供氧条件下,无有机碳源时反应器的硝化反硝化特性.结果表明,在 10～30℃范围内,20℃为临界点,低于20℃时,硝化速率缓慢;高于 20℃后,硝化速率加快.温度从 20℃升高到 30℃,硝化速率增长仅为10%,这一特性与悬浮生长反应器内温度对硝化速率的影响完全不同.此外,稳定运行的 BAF 内存在大量氮流失现象,分析认为,限制供氧和无有机碳源时,生物膜内发生了以 Anammox反应为主的自养反硝化作用,大量的氮以 N₂的形式流失.     

南响堂石窟表面粉尘特征及对石雕影响的研究

从对石窟石雕表面所覆盖的粉尘进行的物、化性能测试分析入手,对粉尘的特征、来源进行了系统地研究,指出粉尘主要由水泥尘、粘土尘、烟及煤炭尘组成,其来源为石窟周边的工业污染源.同时对粉尘与碳酸盐岩石雕表面所发生的各种反应进行了讨论,提出该工业粉尘是导致石窟石雕表面破损的一个不可忽视的重要因素.      

珠海2019年秋季一次大气污染过程的特征、 成因及来源分析

2019年秋季在珠三角典型沿海城市珠海观测到一次中重度污染过程,本文对此次过程的污染特征、形成机制和来源进行了研究.通过 采集PM_2.5样品,分析了9种水溶性无机离子（WSIIs）、有机碳（OC）、元素碳（EC）和水溶性有机碳（WSOC）等化学组分的浓度水平和污染特征;进一步结合污染过程中的不利天气形势、72 h后向气流轨迹及PM_2.5的潜在源贡献因子（WPSCF）和浓度权重轨迹（WCWT）等方法分析了污染的形成机制和来源.结果表明,有机物（OM）是污染时期PM_2.5中增长最快的组分,其次是占WSIIs约82.46%的SO₄^2-、NO₃^-和NH₄⁺（SNA）. NO₃^-/SO₄^2-均值为0.20,表明珠海以固定源污染为主;硫氧化率（SOR）均值为0.65,氮氧化率（NOR）均值为0.08,高温高湿的气象条件可能是 造成珠海比中国其他城市SOR偏高而NOR偏低的原因.在污染时段,二次有机碳（SOC）明显增加,WSOC/SOC随污染物的升高而降低并趋近于1,因此, 污染时期的WSOC可能主要是二次生成的.副高控制型、台风外围型和高压出海型等天气形势控制着整个珠三角地区时,不利于污染物的传输和扩散,使污染加剧.后向气流轨迹分析表明,污染时期的气团轨迹主要来自于高污染的内陆地区,这可能是造成此次污染形成的重要原因和来源.WPSCF和WCWT的高值区主要集中在江西、广东等内陆地区,因此,珠海在控制本地排放的同时,也应该关注上风向临近省市的污染排放.     

Integrated Modular Modeling of Water and Nutrients From Point and Nonpoint Sources in the Patuxent River Watershed1

Abstract: We present a simple modular landscape simulation model that is based on a watershed modeling framework in which different sets of processes occurring in a watershed can be simulated separately with different models. The model consists of three loosely coupled submodels: a rainfall‐runoff model (TOPMODEL) for runoff generation in a subwatershed, a nutrient model for estimation of nutrients from nonpoint sources in a subwatershed, and a stream network model for integration of point and nonpoint sources in the routing process. The model performance was evaluated using monitoring data in the watershed of the Patuxent River, a tributary to the Chesapeake Bay in Maryland, from July 1997 through August 1999. Despite its simplicity, the landscape model predictions of streamflow, and sediment and nutrient loads were as good as or better than those of the Hydrological Simulation Program‐Fortran model, one of the most widely used comprehensive watershed models. The landscape model was applied to predict discharges of water, sediment, silicate, organic carbon, nitrate, ammonium, organic nitrogen, total nitrogen, organic phosphorus, phosphate, and total phosphorus from the Patuxent watershed to its estuary. The predicted annual water discharge to the estuary was very close to the measured annual total in terms of percent errors for both years of the study period (≤2%). The model predictions for loads of nutrients were also good (20‐30%) or very good (<20%) with exceptions of sediment (40%), phosphate (36%), and organic carbon (53%) for Year 1.     

Streambank Soil and Phosphorus Losses Under Different Riparian Land‐Uses in Iowa1

Abstract: Phosphorus and sediment are major nonpoint source pollutants that degrade water quality. Streambank erosion can contribute a significant percentage of the phosphorus and sediment load in streams. Riparian land‐uses can heavily influence streambank erosion. The objective of this study was to compare streambank erosion along reaches of row‐cropped fields, continuous, rotational and intensive rotational grazed pastures, pastures where cattle were fenced out of the stream, grass filters and riparian forest buffers, in three physiographic regions of Iowa. Streambank erosion was measured by surveying the extent of severely eroding banks within each riparian land‐use reach and randomly establishing pin plots on subsets of those eroding banks. Based on these measurements, streambank erosion rate, erosion activity, maximum pin plot erosion rate, percentage of streambank length with severely eroding banks, and soil and phosphorus losses per unit length of stream reach were compared among the riparian land‐uses. Riparian forest buffers had the lowest streambank erosion rate (15‐46 mm/year) and contributed the least soil (5‐18 tonne/km/year) and phosphorus (2‐6 kg/km/year) to stream channels. Riparian forest buffers were followed by grass filters (erosion rates 41‐106 mm/year, soil losses 22‐47 tonne/km/year, phosphorus losses 9‐14 kg/km/year) and pastures where cattle were fenced out of the stream (erosion rates 22‐58 mm/year, soil losses 6‐61 tonne/km/year, phosphorus losses 3‐34 kg/km/year). The streambank erosion rates for the continuous, rotational, and intensive rotational pastures were 101‐171, 104‐122, and 94‐170 mm/year, respectively. The soil losses for the continuous, rotational, and intensive rotational pastures were 197‐264, 94‐266, and 124‐153 tonne/km/year, respectively, while the phosphorus losses were 71‐123, 37‐122, and 66 kg/km/year, respectively. The only significant differences for these pasture practices were found among the percentage of severely eroding bank lengths with intensive rotational grazed pastures having the least compared to the continuous and rotational grazed pastures. Row‐cropped fields had the highest streambank erosion rates (239 mm/year) and soil losses (304 tonne/km/year) and very high phosphorus losses (108 kg/km/year).     

Method to Partition Between Attached and Unattached E. coli in Runoff From Agricultural Lands1

Abstract: Remediation of waters impaired by bacterial indicators is usually dictated by total maximum daily load plans, which are heavily dependent on fate and transport modeling of bacterial indicators. Nonpoint source pollution models are most frequently used to assess bacterial transport to surface waters and most models typically simulate bacterial transport as a dissolved pollutant. Previous studies have found that cells preferentially attach to sediments; however, a variety of techniques have been used to assess attachment including filtration, fractional filtration, and centrifugation. In addition, a variety of chemical and physical dispersion techniques are used to release attached and bioflocculated cells from particulates. Here we developed and validated an easy‐to‐replicate laboratory procedure for separation of unattached from attached E. coli which will also identify particle sizes to which E. coli preferentially attach. Physical and chemical dispersion techniques were evaluated and a combined hand shaker treatment for 10 min followed by dilutions in 1,000 mg/l of Tween 85 significantly increased total E. coli concentrations by 31% when compared with a control. In order to separate unattached from attached fractions, two commonly used techniques, fractional filtration, and centrifugation were combined. The filtration and centrifugation treatments did not reduce E. coli concentrations when compared with a control (p > 0.05), indicating that damage was not inflicted upon the E. coli cells during the separation procedure.     

Kosetice, Czech Republic--ten years of air pollution monitoring and four years of evaluating the origin of persistent organic pollutants

The regional observatory Kosetice is a central European background station. Unique continuous monitoring from 1988 on is held here. POP (persistent organic pollutant) concentration values of air samples from Kosetice taken between 1996 and 2005 were statistically processed. Values of Czech ambient air quality standards were not exceeded. Concentrations of polycyclic aromatic hydrocarbons reached two maxima, in 1996 and 2001-2002. Polychlorinated biphenyls concentrations reached the highest values in 1997 and 1998 and hexachlorocyclohexanes concentrations in 1998. DDTs, hexachlorobenzene and pentachlorobenzene were analysed as well. Long-range transport of pollutants between 2002 and 2005 was evaluated using the Potential Source Contribution Function hybrid receptor model. Indicated potential source areas of PCBs coincide with many well-known urban and industrialised areas, while the indicated potential source areas of HCHs and DDTs coincide with many agricultural and/or forested regions and the potential source areas of HCB comprise all land use types.     

Field monitoring of volatile organic compounds using passive air samplers in an industrial city in Japan

Highly portable, sensitive, and selective passive air samplers were used to investigate ambient volatile organic compound (VOC) levels at multiple sampling sites in an industrial city, Fuji, Japan. We determined the spatial distributions of 27 species of VOCs in three campaigns: Mar (cold season), May (warm season), and Nov (mild season) of 2004. In all campaigns, toluene (geometric mean concentration, 14.0microg/m3) was the most abundant VOC, followed by acetaldehyde (4.76microg/m3), and formaldehyde (2.58microg/m3). The spatial distributions for certain VOCs showed characteristic patterns: high concentrations of benzene and formaldehyde were typically found along major roads, whereas high concentrations of toluene and tetrachloroethylene (PCE) were usually found near factories. The spatial distribution of PCE observed was extremely consistent with the diffusion pattern calculated from Pollutant Release and Transfer Register data and meteorological data, indicated that passive air samplers are useful for determining the sources and distributions of ambient VOCs.     

Diffusion pollution from livestock and poultry rearing in the Yangtze Delta,China

BACKGROUND: The Yangtze Delta is one of the most developed regions in China and includes Shanghai, eight cities in Jiangsu province and eight cities in Zhejiang province. Meat consumption in this region has increased with economic growth, and most of the consumed meat is produced locally. The water quality of surface waters has deteriorated in recent years. An example was the huge blue-green algae bloom in Tai Lake in late May 2007, which affected millions of people's daily drinking water. However, animal husbandry is considered to be one of the main pollution sources. METHODS: Pollutants (NH3-N, total phosphorus (TP), and total nitrogen (TN)) excreted by livestock and poultry, and the resultant COD (chemical oxygen demand) and BOD (biochemical oxygen demand), were estimated using two different methods based on different data sets. RESULTS: The number of livestock and poultry has remained stable in the Yangtze Delta over the four years from 1999 to 2002, with the average number of pigs, cattle, sheep and poultry being 21.1 M, 0.4 M, 7.7 M and 597.6 M, respectively. Pollutants in livestock and poultry excreta estimated by Method I were: 0.12 Mt NH3-N, 0.11 Mt TP and 0.29 Mt TN, resulting in COD and BOD of 1.34 Mt and 1.30 Mt, respectively, while the estimations based on Method II were: 0.18 Mt NH3-N, 0.15 Mt TP and 0.40 Mt TN, resulting in COD and BOD of 1.95 Mt and 1.80 Mt, respectively. DISCUSSION: Pollutants excreted annually by livestock and poultry in the Yangtze Delta are estimated to be: 0.17 Mt NH3-N, 0.16 Mt TP and 0.42 Mt TN, giving rise to a COD of 1.86 Mt and a BOD of 1.72 Mt. Approximately 25% of this pollution was estimated to enter water bodies, which means that the annual pollutant load is 43,700 t NH3-N, 39,400 tTP, 104,600t TN with a COD of 465,000 tand a BOD of 430,100 t. Pollutants from animal husbandry were similar in magnitude to those from industrial wastewater. Pigs produced the most pollution, followed by poultry, cattle and sheep. The pollution load from animal husbandry in the Yangtze Delta is about twice the average level of the whole of China. CONCLUSIONS: Domestic wastewater was the main pollution source in the Yangtze Delta, followed by pollution from raising livestock and poultry and from industrial wastewater. The pollution load in Shanghai and Jiaxing were the greatest, followed by 7 cities of Jiangsu province (except Suzhou) and other cities of Zhejiang province and Suzhou. Pigs and poultry produced about 90% of the total pollutants from animal husbandry. RECOMMENDATIONS AND PERSPECTIVES: The local governments, especially in Shanghai and Jiaxing, should focus their attention on the pollution produced by livestock and poulrry. Controlling pollution from pigs and poultry will have the greatest impact in this region. Control of pollution will be facilitated by the development of large-scale livestock and poultry farming units and a shift away from small scale husbandry.